Hi Jacopo,
Thank you for the patch.
On Tuesday, 10 April 2018 13:54:06 EEST Jacopo Mondi wrote:
> Enable HDMI output on Renesas R-Car V3M Eagle board.
>
> The HDMI output is enabled connecting the DU LVDS output to the
> transparent LVDS converter THC63LVD1024, and successively routing its
> RGB output to the ADV7511W HDMI encoder.
>
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> [for THC63LVD1024: ]
> Reviewed-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
>
> ---
> v1 -> v2:
> - Squash patches [5/7], [6/7] and [7/7] of v1 in a single patch as
> suggested by Laurent
> - Remove DU pinmuxing as it is used for DU parallel RGB output only used
> by Eagle's display expander board not enabled by this series.
> ---
> arch/arm64/boot/dts/renesas/r8a77970-eagle.dts | 93 +++++++++++++++++++++++
> 1 file changed, 93 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
> b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts index 3c5f598..1e2191d
> 100644
> --- a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
> +++ b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
> @@ -31,6 +31,51 @@
> /* first 128MB is reserved for secure area. */
> reg = <0x0 0x48000000 0x0 0x38000000>;
> };
> +
> + hdmi-out {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_out: endpoint {
> + remote-endpoint = <&adv7511_out>;
> + };
> + };
> + };
> +
> + d3p3: regulator-fixed {
> + compatible = "regulator-fixed";
> + regulator-name = "fixed-3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + thc63lvd1024: lvds-decoder {
Nitpicking, no need for a label, you never reference it.
Apart from that, you can keep my Reviewed-by.
> + compatible = "thine,thc63lvd1024";
> +
> + vcc-supply = <&d3p3>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + thc63lvd1024_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + thc63lvd1024_out: endpoint {
> + remote-endpoint = <&adv7511_in>;
> + };
> + };
> + };
> + };
> };
>
> &avb {
> @@ -68,6 +113,38 @@
> gpio-controller;
> #gpio-cells = <2>;
> };
> +
> + hdmi@39 {
> + compatible = "adi,adv7511w";
> + reg = <0x39>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
> +
> + adi,input-depth = <8>;
> + adi,input-colorspace = "rgb";
> + adi,input-clock = "1x";
> + adi,input-style = <1>;
> + adi,input-justification = "evenly";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + adv7511_in: endpoint {
> + remote-endpoint = <&thc63lvd1024_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + adv7511_out: endpoint {
> + remote-endpoint = <&hdmi_con_out>;
> + };
> + };
> + };
> + };
> };
>
> &pfc {
> @@ -93,3 +170,19 @@
>
> status = "okay";
> };
> +
> +&du {
> + status = "okay";
> +};
> +
> +&lvds0 {
> + status = "okay";
> +
> + ports {
> + port@1 {
> + lvds0_out: endpoint {
> + remote-endpoint = <&thc63lvd1024_in>;
> + };
> + };
> + };
> +};
--
Regards,
Laurent Pinchart
