Re: [PATCH v10 01/30] rcar-vin: add Gen3 devicetree bindings documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Niklas,

Thank you for the patch.

On Monday, 29 January 2018 18:34:06 EET Niklas Söderlund wrote:
> Document the devicetree bindings for the CSI-2 inputs available on Gen3.
> 
> There is a need to add a custom property 'renesas,id' and to define
> which CSI-2 input is described in which endpoint under the port@1 node.
> This information is needed since there are a set of predefined routes
> between each VIN and CSI-2 block. This routing table will be kept
> inside the driver but in order for it to act on it it must know which
> VIN and CSI-2 is which.
> 
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>

Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>

> ---
>  .../devicetree/bindings/media/rcar_vin.txt         | 118 +++++++++++++++---
>  1 file changed, 106 insertions(+), 12 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt
> b/Documentation/devicetree/bindings/media/rcar_vin.txt index
> c60e6b0a89b67a8c..90d92836284b7f68 100644
> --- a/Documentation/devicetree/bindings/media/rcar_vin.txt
> +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt
> @@ -2,8 +2,12 @@ Renesas R-Car Video Input driver (rcar_vin)
>  -------------------------------------------
> 
>  The rcar_vin device provides video input capabilities for the Renesas R-Car
> -family of devices. The current blocks are always slaves and suppot one
> input -channel which can be either RGB, YUYV or BT656.
> +family of devices.
> +
> +Each VIN instance has a single parallel input that supports RGB and YUV
> video, +with both external synchronization and BT.656 synchronization for
> the latter. +Depending on the instance the VIN input is connected to
> external SoC pins, or +on Gen3 platforms to a CSI-2 receiver.
> 
>   - compatible: Must be one or more of the following
>     - "renesas,vin-r8a7743" for the R8A7743 device
> @@ -16,6 +20,8 @@ channel which can be either RGB, YUYV or BT656.
>     - "renesas,vin-r8a7793" for the R8A7793 device
>     - "renesas,vin-r8a7794" for the R8A7794 device
>     - "renesas,vin-r8a7795" for the R8A7795 device
> +   - "renesas,vin-r8a7796" for the R8A7796 device
> +   - "renesas,vin-r8a77970" for the R8A77970 device
>     - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 or RZ/G1 compatible
>       device.
>     - "renesas,rcar-gen3-vin" for a generic R-Car Gen3 compatible device.
> @@ -31,21 +37,38 @@ channel which can be either RGB, YUYV or BT656.
>  Additionally, an alias named vinX will need to be created to specify
>  which video input device this is.
> 
> -The per-board settings:
> +The per-board settings Gen2 platforms:
>   - port sub-node describing a single endpoint connected to the vin
>     as described in video-interfaces.txt[1]. Only the first one will
>     be considered as each vin interface has one input port.
> 
> -   These settings are used to work out video input format and widths
> -   into the system.
> +The per-board settings Gen3 platforms:
> 
> +Gen3 platforms can support both a single connected parallel input source
> +from external SoC pins (port0) and/or multiple parallel input sources
> +from local SoC CSI-2 receivers (port1) depending on SoC.
> 
> -Device node example
> --------------------
> +- renesas,id - ID number of the VIN, VINx in the documentation.
> +- ports
> +    - port 0 - sub-node describing a single endpoint connected to the VIN
> +      from external SoC pins described in video-interfaces.txt[1].
> +      Describing more then one endpoint in port 0 is invalid. Only VIN
> +      instances that are connected to external pins should have port 0.
> +    - port 1 - sub-nodes describing one or more endpoints connected to
> +      the VIN from local SoC CSI-2 receivers. The endpoint numbers must
> +      use the following schema.
> 
> -	aliases {
> -	       vin0 = &vin0;
> -	};
> +        - Endpoint 0 - sub-node describing the endpoint connected to CSI20
> +        - Endpoint 1 - sub-node describing the endpoint connected to CSI21
> +        - Endpoint 2 - sub-node describing the endpoint connected to CSI40
> +        - Endpoint 3 - sub-node describing the endpoint connected to CSI41
> +
> +Device node example for Gen2 platforms
> +--------------------------------------
> +
> +        aliases {
> +                vin0 = &vin0;
> +        };
> 
>          vin0: vin@e6ef0000 {
>                  compatible = "renesas,vin-r8a7790",
> "renesas,rcar-gen2-vin"; @@ -55,8 +78,8 @@ Device node example
>                  status = "disabled";
>          };
> 
> -Board setup example (vin1 composite video input)
> -------------------------------------------------
> +Board setup example for Gen2 platforms (vin1 composite video input)
> +-------------------------------------------------------------------
> 
>  &i2c2   {
>          status = "ok";
> @@ -95,6 +118,77 @@ Board setup example (vin1 composite video input)
>          };
>  };
> 
> +Device node example for Gen3 platforms
> +--------------------------------------
> 
> +        vin0: video@e6ef0000 {
> +                compatible = "renesas,vin-r8a7795";
> +                reg = <0 0xe6ef0000 0 0x1000>;
> +                interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
> +                clocks = <&cpg CPG_MOD 811>;
> +                power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> +                resets = <&cpg 811>;
> +                renesas,id = <0>;
> +
> +                ports {
> +                        #address-cells = <1>;
> +                        #size-cells = <0>;
> +
> +                        port@1 {
> +                                #address-cells = <1>;
> +                                #size-cells = <0>;
> +
> +                                reg = <1>;
> +
> +                                vin0csi20: endpoint@0 {
> +                                        reg = <0>;
> +                                        remote-endpoint= <&csi20vin0>;
> +                                };
> +                                vin0csi21: endpoint@1 {
> +                                        reg = <1>;
> +                                        remote-endpoint= <&csi21vin0>;
> +                                };
> +                                vin0csi40: endpoint@2 {
> +                                        reg = <2>;
> +                                        remote-endpoint= <&csi40vin0>;
> +                                };
> +                        };
> +                };
> +        };
> +
> +        csi20: csi2@fea80000 {
> +                compatible = "renesas,r8a7795-csi2";
> +                reg = <0 0xfea80000 0 0x10000>;
> +                interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> +                clocks = <&cpg CPG_MOD 714>;
> +                power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> +                resets = <&cpg 714>;
> +
> +                ports {
> +                        #address-cells = <1>;
> +                        #size-cells = <0>;
> +
> +                        port@0 {
> +                                reg = <0>;
> +                                csi20_in: endpoint {
> +                                        clock-lanes = <0>;
> +                                        data-lanes = <1>;
> +                                        remote-endpoint = <&adv7482_txb>;
> +                                };
> +                        };
> +
> +                        port@1 {
> +                                #address-cells = <1>;
> +                                #size-cells = <0>;
> +
> +                                reg = <1>;
> +
> +                                csi20vin0: endpoint@0 {
> +                                        reg = <0>;
> +                                        remote-endpoint = <&vin0csi20>;
> +                                };
> +                        };
> +                };
> +        };
> 
>  [1] video-interfaces.txt common video media interface


-- 
Regards,

Laurent Pinchart





[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux