Hi Laurent,
On Tue, Jan 02, 2018 at 01:45:30PM +0200, Laurent Pinchart wrote:
> Hi Jacopo,
>
> Thank you for the patch.
>
> On Thursday, 28 December 2017 16:01:13 EET Jacopo Mondi wrote:
> > Add bindings documentation for Renesas Capture Engine Unit (CEU).
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > ---
> > .../devicetree/bindings/media/renesas,ceu.txt | 85 +++++++++++++++++++
> > 1 file changed, 85 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt
> > b/Documentation/devicetree/bindings/media/renesas,ceu.txt new file mode
> > 100644
> > index 0000000..f45628e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
> > @@ -0,0 +1,85 @@
> > +Renesas Capture Engine Unit (CEU)
> > +----------------------------------------------
> > +
> > +The Capture Engine Unit is the image capture interface found on Renesas
> > +RZ chip series and on SH Mobile ones.
>
> "ones" sound a bit weird. How about "... found in the Renesas SH Mobil and RZ
> SoCs." ?
>
> > +The interface supports a single parallel input with data bus width up to
> > +8/16 bits.
>
> What do you mean by "up to 8/16 bits" ?
The input bus width can be 8 or 16 bit.
On a general note: I always assumed DT bindings should describe the
hardware capabilities. In this case the hardware supports 8 or 16 bits
as input width, but the driver only cares about the 8 bits case. Which
one should I describe here?
I will fix all of yours and Geert's remarks in V3.
Thanks
j
>
> > +Required properties:
> > +- compatible
> > + Must be one of:
> > + - "renesas,ceu"
> > + - "renesas,r7s72100-ceu"
>
> This is unclear, as Geert pointed out renesas,ceu sounds like a fallback. I
> think this could be clarified if you explained how you plan to support other
> SoCs (in particular the SH Mobile series, when/if it will receive DT support).
>
> > +- reg
> > + Physical address base and size.
>
> The standard practice, if I'm not mistaken, is to document properties with the
> description starting on the same line as the property name.
>
> - reg: Physical address base and size.
>
> And nitpicking again, I'd write "register" instead of "physical" to clarify
> what the properties contains (even if its name should make it clear).
>
> > +- interrupts
> > + The interrupt specifier.
> > +- pinctrl-names, pinctrl-0
> > + phandle of pin controller sub-node configuring pins for CEU operations.
>
> pinctrl-names isn't a phandle. If you want to document those properties (not
> all DT bindings do, I'm not sure what is best) you should document them both,
> possibly on two separate lines. There are plenty of examples in the upstream
> DT bindings.
>
> > +- remote-endpoint
> > + phandle to an 'endpoint' subnode of a remote device node.
>
> As Geert pointed out this isn't a top-level property. I wouldn't document it
> as such, but instead reference Documentation/devicetree/bindings/media/video-
> interfaces.txt (see Documentation/devicetree/bindings/display/renesas,du.txt
> or Documentation/devicetree/bindings/media/renesas,drif.txt for examples).
>
> > +CEU supports a single parallel input and should contain a single 'port'
>
> s/CEU/The CEU/
>
> > subnode
> > +with a single 'endpoint'. Optional endpoint properties applicable to
> > parallel
> > +input bus described in "video-interfaces.txt" supported by this driver are:
> > +
> > +- hsync-active
> > + active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> > +- vsync-active
> > + active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> > +
> > +Example:
> > +
> > +The example describes the connection between the Capture Engine Unit and an
> > +OV7670 image sensor sitting on bus i2c1.
>
> Maybe s/sitting on/connected to/ ?
>
> > +ceu: ceu@e8210000 {
> > + reg = <0xe8210000 0x209c>;
> > + compatible = "renesas,ceu";
> > + interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vio_pins>;
> > +
> > + status = "okay";
> > +
> > + port {
> > + ceu_in: endpoint {
> > + remote-endpoint = <&ov7670_out>;
> > +
> > + hsync-active = <1>;
> > + vsync-active = <0>;
> > + };
> > + };
> > +};
> > +
> > +i2c1: i2c@fcfee400 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c1_pins>;
> > +
> > + status = "okay";
> > +
> > + clock-frequency = <100000>;
> > +
> > + ov7670: camera@21 {
> > + compatible = "ovti,ov7670";
> > + reg = <0x21>;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vio_pins>;
> > +
> > + reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
> > + powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
> > +
> > + port {
> > + ov7670_out: endpoint {
> > + remote-endpoint = <&ceu_in>;
> > +
> > + hsync-active = <1>;
> > + vsync-active = <0>;
> > + };
> > + };
> > + };
> > +};
>
> --
> Regards,
>
> Laurent Pinchart
>
