Hi Vladimir,
Happy New Year!
On Fri, Dec 22, 2017 at 12:22:09PM +0200, Vladimir Zapolskiy wrote:
> Hi Simon,
>
> On 12/22/2017 10:40 AM, Simon Horman wrote:
> > On Fri, Dec 22, 2017 at 09:32:03AM +0100, Simon Horman wrote:
> >> On Thu, Dec 21, 2017 at 05:18:58PM +0200, Vladimir Zapolskiy wrote:
> >>> From: Bogdan Mirea <Bogdan-Stefan_Mirea@xxxxxxxxxx>
> >>>
> >>> The present change is a bug fix for AVB link iteratively up/down.
> >>>
> >>> Steps to reproduce:
> >>> - start AVB TX stream (Using aplay via MSE),
> >>> - disconnect+reconnect the eth cable,
> >>> - after a reconnection the eth connection goes iteratively up/down
> >>> without user interaction,
> >>> - this may heal after some seconds or even stay for minutes.
> >>>
> >>> As the documentation specifies, the "renesas,no-ether-link" option
> >>> should be used when a board does not provide a proper AVB_LINK signal.
> >>> There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
> >>> and ULCB starter kits since the AVB_LINK is correctly handled by HW.
> >>>
> >>> Choosing to keep or remove the "renesas,no-ether-link" option will
> >>> have impact on the code flow in the following ways:
> >>> - keeping this option enabled may lead to unexpected behavior since
> >>> the RX & TX are enabled/disabled directly from adjust_link function
> >>> without any HW interrogation,
> >>> - removing this option, the RX & TX will only be enabled/disabled after
> >>> HW interrogation. The HW check is made through the LMON pin in PSR
> >>> register which specifies AVB_LINK signal value (0 - at low level;
> >>> 1 - at high level).
> >>>
> >>> In conclusion, the present change is also a safety improvement because
> >>> it removes the "renesas,no-ether-link" option leading to a proper way
> >>> of detecting the link state based on HW interrogation and not on
> >>> software heuristic.
> >>>
> >>> Fixes: d25e8ff0d5aa ("arm64: dts: renesas: Extract common Salvator-X board support")
> >>
> >> The above shuffles the code around but does not introduce the problem
> >> as far as I can see. Instead I think we should use:
> >>
> >> Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
> >> Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
> >>
> >>> Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@xxxxxxxxxx>
> >>> Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@xxxxxxxxxx>
> >
> > I have applied this a fix for v4.15 with the updated Fixes tags above.
> >
>
> thank you, I was unsure if you expected to get changes which can be used
> as a base without patch application conflicts (my done choice) or changes,
> which originally intorduced the bug, but formally require slightly
> different fixes due to code changes in the middle. If it would be needed,
> hopefully linux-stable maintainers can resolve the trivial conflicts.
>
> Also you may find this information from the cover letter useful,
> someone may want to check the relevant board schematics and send
> similar fixes (if applicable after schematics review and testing):
>
> Note that DTS files for V3M Starter Kit, Draak and Eagle boards
> contain the same property, the files are untouched due to unavailable
> schematics to verify if the fix applies to these boards as well.
Thanks. I took a quick look and my findings so far are:
* Eagle: This approach seems applicable as AVB_LINK appears to be hooked up
* V3M Starter Kit: This approach seems applicable as AVB0_LINK appears to be
hooked up
* Draak: I don't seem to be able to locate documentation at this time
Are you interested in creating follow-up patches?
