Hi Olof, Hi Kevin, Hi Arnd, Please consider these Renesas ARM64 based SoC DT updates for v4.15. The following changes since commit 2bd6bf03f4c1c59381d62c61d03f6cc3fe71f66e: Linux 4.14-rc1 (2017-09-16 15:47:51 -0700) are available in the git repository at: https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.15 for you to fetch changes up to 2affee619d48d101831e83e74cadeb7c5200d9cb: arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node (2017-09-25 09:09:51 +0200) ---------------------------------------------------------------- Renesas ARM64 Based SoC DT Updates for v4.15 * r8a7795 (H3) - Use r8a7795-cpg-mssr and r8a7795-sysc bindings Hardcoded indicies are replaced with symbols now that they are available - Drop bogus HDMI node name suffixes Laurent Pinchart says: Node names should not use numerical suffixes if the nodes can be distinguished by unit-address - Update PFC node name to pin-controller Shimoda-san says the PFC node name is changed "from e6060000.pfc and pfc@e6060000 to e6060000.pin-controller and pin-controller@e6060000 like other Renesas SoCs." * r8a7795 (H3) ES1.0 - Drop extra zero from XHCI unit address This corrects a typo were ee0400000 rather than ee040000 was used as the unit address. * r8a7796 (M3-W) - Add FDP1 instance Laurent Pinchart says: The r8a7796 has a single FDP1 instance. * r8a7795 (H3) and r8a7796 (M3-W) SoCs - Add USB3.0 peripheral device nodes Shimoda-san says that this is not enabled on the Salvator-X/XS boards for now as: + we need a special cable (USB type-A to A cross cable). + we can swap the role by renesas_usb3 driver even if we use a normal cable and after usb3.0 host is running, but I think it's a special use case. * r8a7795 (H3) and r8a7796 (M3-W) ULCB boards - Enable display output Laurent Pinchart says: The DU is already wired up to the HDMI encoder, all we need to do is enable it. * r8a77995 (D3) Draak board - Enable EthernetAVB and , USB2.0 Host and PHY - Add serial console pins. This is safe to do now that r8a77995 PFC driver support is present * r8a77970 (V3M) - Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC in the Eagle board support for which is under review ---------------------------------------------------------------- Geert Uytterhoeven (6): arm64: dts: renesas: r8a7795-es1: Drop extra zero from usb unit address arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes arm64: renesas: Add Renesas R8A77970 Kconfig support arm64: dts: renesas: r8a77995: Use r8a7795-sysc binding definitions arm64: dts: renesas: r8a77995: Use r8a7795-cpg-mssr binding definitions arm64: dts: draak: Add serial console pins Laurent Pinchart (2): arm64: dts: renesas: r8a7796: Add FDP1 instance arm64: dts: renesas: ulcb: Enable display output Sergei Shtylyov (4): arm64: dts: renesas: initial R8A77970 SoC device tree arm64: dts: renesas: r8a77970: add SYS-DMAC support arm64: dts: renesas: r8a77970: add [H]SCIF support arm64: dts: renesas: r8a77970: add EtherAVB support Yoshihiro Shimoda (10): arm64: dts: renesas: r8a77995: update PFC node name to pin-controller arm64: dts: renesas: r8a77995: add GPIO device nodes arm64: dts: renesas: r8a77995: Add EthernetAVB device node arm64: dts: renesas: r8a77995: Add USB2.0 PHY device node arm64: dts: renesas: r8a77995: add USB2.0 Host (EHCI/OHCI) device node arm64: dts: renesas: r8a77995: draak: enable USB2.0 PHY arm64: dts: renesas: r8a77995: draak: enable USB2.0 Host (EHCI/OHCI) arm64: dts: renesas: r8a77995: draak: enable EthernetAVB arm64: dts: renesas: r8a7795: add USB3.0 peripheral device node arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node arch/arm64/Kconfig.platforms | 6 + arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi | 2 +- arch/arm64/boot/dts/renesas/r8a7795.dtsi | 15 +- arch/arm64/boot/dts/renesas/r8a7796.dtsi | 21 ++ arch/arm64/boot/dts/renesas/r8a77970.dtsi | 366 +++++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 55 ++++ arch/arm64/boot/dts/renesas/r8a77995.dtsi | 211 +++++++++++++- arch/arm64/boot/dts/renesas/ulcb.dtsi | 4 + 8 files changed, 669 insertions(+), 11 deletions(-) create mode 100644 arch/arm64/boot/dts/renesas/r8a77970.dtsi
