On 06/27/2017 05:03 PM, Kieran Bingham wrote:
From: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
---
v2:
- Implement DT parsing
- adv748x: Add CSI2 entity
- adv748x: Rework pad allocations and fmts
- Give AFE 8 input pads and move pad defines
- Use the enums to ensure pads are referenced correctly.
- adv748x: Rename AFE/HDMI entities
Now they are 'just afe' and 'just hdmi'
- Reorder the entity enum and structures
- Added pad-format for the CSI2 entities
- CSI2 s_stream pass through
- CSI2 control pass through (with link following)
v3:
- dt: Extend DT documentation to specify interrupt mappings
- simplify adv748x_parse_dt
- core: Add banner to header file describing ADV748x variants
- Use entity structure pointers rather than global state pointers where
possible
- afe: Reduce indent on afe_status
- hdmi: Add error checking to the bt->pixelclock values.
- Remove all unnecessary pad checks: handled by core
- Fix all probe cleanup paths
- adv748x_csi2_probe() now fails if it has no endpoint
- csi2: Fix small oneliners for is_txa and get_remote_sd()
- csi2: Fix checkpatch warnings
- csi2: Fix up s_stream pass-through
- csi2: Fix up Pixel Rate passthrough
- csi2: simplify adv748x_csi2_get_pad_format()
- Remove 'async notifiers' from AFE/HDMI
Using async notifiers was overkill, when we have access to the
subdevices internally and can register them directly.
- Use state lock in control handlers and clean up s_ctrls
- remove _interruptible mutex locks
v4:
- all: Convert hex 0xXX to lowercase
- all: Use defines instead of hardcoded register values
- all: Use regmap
- afe, csi2, hdmi: _probe -> _init
- afe, csi2, hdmi: _remove -> _cleanup
- afe, hdmi: Convert pattern generator to a control
- afe, hdmi: get/set-fmt refactor
- afe, hdmi, csi2: Convert to internal calls for pixelrate
- afe: Allow the AFE to configure the Input Select from DT
- afe: Reduce indent on adv748x_afe_status switch
- afe: Remove ununsed macro definitions AIN0-7
- afe: Remove extraneous control checks handled by core
- afe: Comment fixups
- afe: Rename error label
- afe: Correct control names on the SDP
- afe: Use AIN0-7 rather than AIN1-8 to match ports and MC pads
- core: adv748x_parse_dt references to nodes, and catch multiple
endpoints in a port.
- core: adv748x_dt_cleanup to simplify releasing DT nodes
- core: adv748x_print_info renamed to adv748x_identify_chip
- core: reorganise ordering of probe sequence
- core: No need for of_match_ptr
- core: Fix up i2c read/writes (regmap still on todo list)
- core: Set specific functions from the entities on subdev-init
- core: Use kzalloc for state instead of devm
- core: Improve probe error reporting
- core: Track unknown BIT(6) in tx{a,b}_power
- csi2: Improve adv748x_csi2_get_remote_sd as adv748x_csi2_get_source_sd
- csi2: -EPIPE instead of -ENODEV
- csi2: adv_dbg, instead of adv_info
- csi2: adv748x_csi2_set_format fix
- csi2: remove async notifier and sd member variables
- csi2: register links from the CSI2
- csi2: create virtual channel helper function
- dt: Remove numbering from endpoints
- dt: describe ports and interrupts as optional
- dt: Re-tab
- hdmi: adv748x_hdmi_have_signal -> adv748x_hdmi_has_signal
- hdmi: fix adv748x_hdmi_read_pixelclock return checks
- hdmi: improve adv748x_hdmi_set_video_timings
- hdmi: Fix tmp variable as polarity
- hdmi: Improve adv748x_hdmi_s_stream
- hdmi: Clean up adv748x_hdmi_s_ctrl register definitions and usage
- hdmi: Fix up adv748x_hdmi_s_dv_timings with macro names for register
- hdmi: Add locking to adv748x_hdmi_g_dv_timings
writes and locking
- hdmi: adv748x_hdmi_set_de_timings function added to clarify DE writes
- hdmi: Use CP in control register naming to match component processor
- hdmi: clean up adv748x_hdmi_query_dv_timings()
- KConfig: Fix up dependency and capitalisation
v5:
- afe,hdmi: _set_pixelrate -> _propagate_pixelrate
- hdmi: Fix arm32 compilation failure : Use DIV_ROUND_CLOSEST_ULL
- core: remove unused link functions
- csi2: Use immutable links for HDMI->TXA, AFE->TXB
v6:
- hdmi: Provide EDID support
- afe: Fix InLock inversion bug
- afe: Prevent autodetection of input format except in querystd
- afe,hdmi: Improve pattern generator control strings
- hdmi: Remove interlaced support capability (it's untested)
drivers/media/i2c/Kconfig | 11 +-
drivers/media/i2c/Makefile | 1 +-
drivers/media/i2c/adv748x/Makefile | 7 +-
drivers/media/i2c/adv748x/adv748x-afe.c | 545 ++++++++++++++++-
drivers/media/i2c/adv748x/adv748x-core.c | 831 ++++++++++++++++++++++++-
drivers/media/i2c/adv748x/adv748x-csi2.c | 327 +++++++++-
drivers/media/i2c/adv748x/adv748x-hdmi.c | 769 ++++++++++++++++++++++-
drivers/media/i2c/adv748x/adv748x.h | 425 ++++++++++++-
8 files changed, 2916 insertions(+)
create mode 100644 drivers/media/i2c/adv748x/Makefile
create mode 100644 drivers/media/i2c/adv748x/adv748x-afe.c
create mode 100644 drivers/media/i2c/adv748x/adv748x-core.c
create mode 100644 drivers/media/i2c/adv748x/adv748x-csi2.c
create mode 100644 drivers/media/i2c/adv748x/adv748x-hdmi.c
create mode 100644 drivers/media/i2c/adv748x/adv748x.h
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 121b3b5394cb..7641667c00ab 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -204,6 +204,17 @@ config VIDEO_ADV7183
To compile this driver as a module, choose M here: the
module will be called adv7183.
+config VIDEO_ADV748X
+ tristate "Analog Devices ADV748x decoder"
+ depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
+ depends on OF
+ ---help---
+ V4L2 subdevice driver for the Analog Devices
+ ADV7481 and ADV7482 HDMI/Analog video decoders.
+
+ To compile this driver as a module, choose M here: the
+ module will be called adv748x.
+
config VIDEO_ADV7604
tristate "Analog Devices ADV7604 decoder"
depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 2c0868fa6034..30e856c02422 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o
obj-$(CONFIG_VIDEO_ADV7183) += adv7183.o
obj-$(CONFIG_VIDEO_ADV7343) += adv7343.o
obj-$(CONFIG_VIDEO_ADV7393) += adv7393.o
+obj-$(CONFIG_VIDEO_ADV748X) += adv748x/
obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o
obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o
obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o
diff --git a/drivers/media/i2c/adv748x/Makefile b/drivers/media/i2c/adv748x/Makefile
new file mode 100644
index 000000000000..c0711e076f1d
--- /dev/null
+++ b/drivers/media/i2c/adv748x/Makefile
@@ -0,0 +1,7 @@
+adv748x-objs := \
+ adv748x-afe.o \
+ adv748x-core.o \
+ adv748x-csi2.o \
+ adv748x-hdmi.o
+
+obj-$(CONFIG_VIDEO_ADV748X) += adv748x.o
diff --git a/drivers/media/i2c/adv748x/adv748x-afe.c b/drivers/media/i2c/adv748x/adv748x-afe.c
new file mode 100644
index 000000000000..f19b05e2780d
--- /dev/null
+++ b/drivers/media/i2c/adv748x/adv748x-afe.c
@@ -0,0 +1,545 @@
+/*
+ * Driver for Analog Devices ADV748X 8 channel analog front end (AFE) receiver
+ * with standard definition processor (SDP)
+ *
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/v4l2-dv-timings.h>
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-dv-timings.h>
+#include <media/v4l2-ioctl.h>
+
+#include "adv748x.h"
+
+/* -----------------------------------------------------------------------------
+ * SDP
+ */
+
+#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM 0x0
+#define ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM_PED 0x1
+#define ADV748X_AFE_STD_AD_PAL_N_NTSC_J_SECAM 0x2
+#define ADV748X_AFE_STD_AD_PAL_N_NTSC_M_SECAM 0x3
+#define ADV748X_AFE_STD_NTSC_J 0x4
+#define ADV748X_AFE_STD_NTSC_M 0x5
+#define ADV748X_AFE_STD_PAL60 0x6
+#define ADV748X_AFE_STD_NTSC_443 0x7
+#define ADV748X_AFE_STD_PAL_BG 0x8
+#define ADV748X_AFE_STD_PAL_N 0x9
+#define ADV748X_AFE_STD_PAL_M 0xa
+#define ADV748X_AFE_STD_PAL_M_PED 0xb
+#define ADV748X_AFE_STD_PAL_COMB_N 0xc
+#define ADV748X_AFE_STD_PAL_COMB_N_PED 0xd
+#define ADV748X_AFE_STD_PAL_SECAM 0xe
+#define ADV748X_AFE_STD_PAL_SECAM_PED 0xf
+
+static int adv748x_afe_read_ro_map(struct adv748x_state *state, u8 reg)
+{
+ int ret;
+
+ /* Select SDP Read-Only Main Map */
+ ret = sdp_write(state, ADV748X_SDP_MAP_SEL,
+ ADV748X_SDP_MAP_SEL_RO_MAIN);
+ if (ret < 0)
+ return ret;
+
+ return sdp_read(state, reg);
+}
+
+static int adv748x_afe_status(struct adv748x_afe *afe, u32 *signal,
+ v4l2_std_id *std)
+{
+ struct adv748x_state *state = adv748x_afe_to_state(afe);
+ int info;
+
+ /* Read status from reg 0x10 of SDP RO Map */
+ info = adv748x_afe_read_ro_map(state, ADV748X_SDP_RO_10);
+ if (info < 0)
+ return info;
+
+ if (signal)
+ *signal = info & ADV748X_SDP_RO_10_IN_LOCK ?
+ 0 : V4L2_IN_ST_NO_SIGNAL;
+
+ if (!std)
+ return 0;
+
+ /* Standard not valid if there is no signal */
+ if (!(info & ADV748X_SDP_RO_10_IN_LOCK)) {
+ *std = V4L2_STD_UNKNOWN;
+ return 0;
+ }
+
+ switch (info & 0x70) {
+ case 0x00:
+ *std = V4L2_STD_NTSC;
+ break;
+ case 0x10:
+ *std = V4L2_STD_NTSC_443;
+ break;
+ case 0x20:
+ *std = V4L2_STD_PAL_M;
+ break;
+ case 0x30:
+ *std = V4L2_STD_PAL_60;
+ break;
+ case 0x40:
+ *std = V4L2_STD_PAL;
+ break;
+ case 0x50:
+ *std = V4L2_STD_SECAM;
+ break;
+ case 0x60:
+ *std = V4L2_STD_PAL_Nc | V4L2_STD_PAL_N;
+ break;
+ case 0x70:
+ *std = V4L2_STD_SECAM;
+ break;
+ default:
+ *std = V4L2_STD_UNKNOWN;
+ break;
+ }
+
+ return 0;
+}
+
+static void adv748x_afe_fill_format(struct adv748x_afe *afe,
+ struct v4l2_mbus_framefmt *fmt)
+{
+ memset(fmt, 0, sizeof(*fmt));
+
+ fmt->code = MEDIA_BUS_FMT_UYVY8_2X8;
+ fmt->colorspace = V4L2_COLORSPACE_SMPTE170M;
+ fmt->field = V4L2_FIELD_INTERLACED;
+
+ fmt->width = 720;
+ fmt->height = afe->curr_norm & V4L2_STD_525_60 ? 480 : 576;
+}
+
+static int adv748x_afe_std(v4l2_std_id std)
+{
+ if (std == V4L2_STD_PAL_60)
+ return ADV748X_AFE_STD_PAL60;
+ if (std == V4L2_STD_NTSC_443)
+ return ADV748X_AFE_STD_NTSC_443;
+ if (std == V4L2_STD_PAL_N)
+ return ADV748X_AFE_STD_PAL_N;
+ if (std == V4L2_STD_PAL_M)
+ return ADV748X_AFE_STD_PAL_M;
+ if (std == V4L2_STD_PAL_Nc)
+ return ADV748X_AFE_STD_PAL_COMB_N;
+ if (std & V4L2_STD_NTSC)
+ return ADV748X_AFE_STD_NTSC_M;
+ if (std & V4L2_STD_PAL)
+ return ADV748X_AFE_STD_PAL_BG;
+ if (std & V4L2_STD_SECAM)
+ return ADV748X_AFE_STD_PAL_SECAM;
+
+ return -EINVAL;
+}
+
+static void adv748x_afe_set_video_standard(struct adv748x_state *state,
+ int sdpstd)
+{
+ sdp_clrset(state, ADV748X_SDP_VID_SEL, ADV748X_SDP_VID_SEL_MASK,
+ (sdpstd & 0xf) << ADV748X_SDP_VID_SEL_SHIFT);
+}
+
+static int adv748x_afe_s_input(struct adv748x_afe *afe, unsigned int input)
+{
+ struct adv748x_state *state = adv748x_afe_to_state(afe);
+
+ return sdp_write(state, ADV748X_SDP_INSEL, input);
+}
+
+static int adv748x_afe_g_pixelaspect(struct v4l2_subdev *sd,
+ struct v4l2_fract *aspect)
+{
+ struct adv748x_afe *afe = adv748x_sd_to_afe(sd);
+
+ if (afe->curr_norm & V4L2_STD_525_60) {
+ aspect->numerator = 11;
+ aspect->denominator = 10;
+ } else {
+ aspect->numerator = 54;
+ aspect->denominator = 59;
+ }
+
+ return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * v4l2_subdev_video_ops
+ */
+
+static int adv748x_afe_g_std(struct v4l2_subdev *sd, v4l2_std_id *norm)
+{
+ struct adv748x_afe *afe = adv748x_sd_to_afe(sd);
+
+ *norm = afe->curr_norm;
+
+ return 0;
+}
+
+static int adv748x_afe_s_std(struct v4l2_subdev *sd, v4l2_std_id std)
+{
+ struct adv748x_afe *afe = adv748x_sd_to_afe(sd);
+ struct adv748x_state *state = adv748x_afe_to_state(afe);
+ int afe_std = adv748x_afe_std(std);
+
+ if (afe_std < 0)
+ return afe_std;
+
+ mutex_lock(&state->mutex);
+
+ adv748x_afe_set_video_standard(state, afe_std);
+ afe->curr_norm = std;
+
+ mutex_unlock(&state->mutex);
+
+ return 0;
+}
+
+static int adv748x_afe_querystd(struct v4l2_subdev *sd, v4l2_std_id *std)
+{
+ struct adv748x_afe *afe = adv748x_sd_to_afe(sd);
+ struct adv748x_state *state = adv748x_afe_to_state(afe);
+ int ret;
+
+ mutex_lock(&state->mutex);
+
+ if (afe->streaming) {
+ ret = -EBUSY;
+ goto unlock;
+ }
+
+ /* Set auto detect mode */
+ adv748x_afe_set_video_standard(state,
+ ADV748X_AFE_STD_AD_PAL_BG_NTSC_J_SECAM);
+
+ msleep(100);
+
+ /* Read detected standard */
+ ret = adv748x_afe_status(afe, NULL, std);
Shouldn't you restore the video standard at this point after changing it above?
+unlock:
+ mutex_unlock(&state->mutex);
+
+ return ret;
+}
<snip>
+int adv748x_afe_init(struct adv748x_afe *afe)
+{
+ struct adv748x_state *state = adv748x_afe_to_state(afe);
+ int ret;
+ unsigned int i;
+
+ afe->input = 0;
+ afe->streaming = false;
+ afe->curr_norm = V4L2_STD_ALL;
This isn't valid. Usually the initial standard is set to NTSC_M.
+
+ adv748x_subdev_init(&afe->sd, state, &adv748x_afe_ops,
+ MEDIA_ENT_F_ATV_DECODER, "afe");
+
+ /* Identify the first connector found as a default input if set */
+ for (i = ADV748X_PORT_AIN0; i <= ADV748X_PORT_AIN7; i++) {
+ /* Inputs and ports are 1-indexed to match the data sheet */
+ if (state->endpoints[i]) {
+ afe->input = i;
+ break;
+ }
+ }
+
+ adv748x_afe_s_input(afe, afe->input);
+
+ adv_dbg(state, "AFE Default input set to %d\n", afe->input);
+
+ /* Entity pads and sinks are 0-indexed to match the pads */
+ for (i = ADV748X_AFE_SINK_AIN0; i <= ADV748X_AFE_SINK_AIN7; i++)
+ afe->pads[i].flags = MEDIA_PAD_FL_SINK;
+
+ afe->pads[ADV748X_AFE_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&afe->sd.entity, ADV748X_AFE_NR_PADS,
+ afe->pads);
+ if (ret)
+ return ret;
+
+ ret = adv748x_afe_init_controls(afe);
+ if (ret)
+ goto error;
+
+ return 0;
+
+error:
+ media_entity_cleanup(&afe->sd.entity);
+
+ return ret;
+}
+
+void adv748x_afe_cleanup(struct adv748x_afe *afe)
+{
+ v4l2_device_unregister_subdev(&afe->sd);
+ media_entity_cleanup(&afe->sd.entity);
+ v4l2_ctrl_handler_free(&afe->ctrl_hdl);
+}
<snip>
diff --git a/drivers/media/i2c/adv748x/adv748x-hdmi.c b/drivers/media/i2c/adv748x/adv748x-hdmi.c
new file mode 100644
index 000000000000..6ab3f9791b4f
--- /dev/null
+++ b/drivers/media/i2c/adv748x/adv748x-hdmi.c
@@ -0,0 +1,769 @@
+/*
+ * Driver for Analog Devices ADV748X HDMI receiver and Component Processor (CP)
+ *
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/mutex.h>
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-dv-timings.h>
+#include <media/v4l2-ioctl.h>
+
+#include <uapi/linux/v4l2-dv-timings.h>
+
+#include "adv748x.h"
+
+/* -----------------------------------------------------------------------------
+ * HDMI and CP
+ */
+
+#define ADV748X_HDMI_MIN_WIDTH 640
+#define ADV748X_HDMI_MAX_WIDTH 1920
+#define ADV748X_HDMI_MIN_HEIGHT 480
+#define ADV748X_HDMI_MAX_HEIGHT 1200
+#define ADV748X_HDMI_MIN_PIXELCLOCK 0 /* unknown */
0 makes no sense. Something like 13000000 would work better (pixelclock rate for
V4L2_DV_BT_CEA_720X480I59_94 is 13500000).
+#define ADV748X_HDMI_MAX_PIXELCLOCK 162000000
You probably based that on the 1600x1200p60 format?
162MHz is a bit low for an adv receiver. The adv7604 and adv8742 have a max rate of 225 MHz.
This should be documented in the datasheet.
Besides, you need a bit of margin since detected pixelclock rates can be a bit off.
+
+static const struct v4l2_dv_timings_cap adv748x_hdmi_timings_cap = {
+ .type = V4L2_DV_BT_656_1120,
+ /* keep this initialization for compatibility with GCC < 4.4.6 */
+ .reserved = { 0 },
+ /* Min pixelclock value is unknown */
+ V4L2_INIT_BT_TIMINGS(ADV748X_HDMI_MIN_WIDTH, ADV748X_HDMI_MAX_WIDTH,
+ ADV748X_HDMI_MIN_HEIGHT, ADV748X_HDMI_MAX_HEIGHT,
+ ADV748X_HDMI_MIN_PIXELCLOCK,
+ ADV748X_HDMI_MAX_PIXELCLOCK,
+ V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT,
+ V4L2_DV_BT_CAP_PROGRESSIVE)
+};
+
+struct adv748x_hdmi_video_standards {
+ struct v4l2_dv_timings timings;
+ u8 vid_std;
+ u8 v_freq;
+};
+
+static const struct adv748x_hdmi_video_standards
+adv748x_hdmi_video_standards[] = {
+ { V4L2_DV_BT_CEA_720X480I59_94, 0x40, 0x00 },
+ { V4L2_DV_BT_CEA_720X576I50, 0x41, 0x01 },
Since adv748x_hdmi_timings_cap doesn't specify CAP_INTERLACED you shouldn't
add these interlaced timings in this list.
+ { V4L2_DV_BT_CEA_720X480P59_94, 0x4a, 0x00 },
+ { V4L2_DV_BT_CEA_720X576P50, 0x4b, 0x00 },
+ { V4L2_DV_BT_CEA_1280X720P60, 0x53, 0x00 },
+ { V4L2_DV_BT_CEA_1280X720P50, 0x53, 0x01 },
+ { V4L2_DV_BT_CEA_1280X720P30, 0x53, 0x02 },
+ { V4L2_DV_BT_CEA_1280X720P25, 0x53, 0x03 },
+ { V4L2_DV_BT_CEA_1280X720P24, 0x53, 0x04 },
+ { V4L2_DV_BT_CEA_1920X1080I60, 0x54, 0x00 },
+ { V4L2_DV_BT_CEA_1920X1080I50, 0x54, 0x01 },
+ { V4L2_DV_BT_CEA_1920X1080P60, 0x5e, 0x00 },
+ { V4L2_DV_BT_CEA_1920X1080P50, 0x5e, 0x01 },
+ { V4L2_DV_BT_CEA_1920X1080P30, 0x5e, 0x02 },
+ { V4L2_DV_BT_CEA_1920X1080P25, 0x5e, 0x03 },
+ { V4L2_DV_BT_CEA_1920X1080P24, 0x5e, 0x04 },
+ /* SVGA */
+ { V4L2_DV_BT_DMT_800X600P56, 0x80, 0x00 },
+ { V4L2_DV_BT_DMT_800X600P60, 0x81, 0x00 },
+ { V4L2_DV_BT_DMT_800X600P72, 0x82, 0x00 },
+ { V4L2_DV_BT_DMT_800X600P75, 0x83, 0x00 },
+ { V4L2_DV_BT_DMT_800X600P85, 0x84, 0x00 },
+ /* SXGA */
+ { V4L2_DV_BT_DMT_1280X1024P60, 0x85, 0x00 },
+ { V4L2_DV_BT_DMT_1280X1024P75, 0x86, 0x00 },
+ /* VGA */
+ { V4L2_DV_BT_DMT_640X480P60, 0x88, 0x00 },
+ { V4L2_DV_BT_DMT_640X480P72, 0x89, 0x00 },
+ { V4L2_DV_BT_DMT_640X480P75, 0x8a, 0x00 },
+ { V4L2_DV_BT_DMT_640X480P85, 0x8b, 0x00 },
+ /* XGA */
+ { V4L2_DV_BT_DMT_1024X768P60, 0x8c, 0x00 },
+ { V4L2_DV_BT_DMT_1024X768P70, 0x8d, 0x00 },
+ { V4L2_DV_BT_DMT_1024X768P75, 0x8e, 0x00 },
+ { V4L2_DV_BT_DMT_1024X768P85, 0x8f, 0x00 },
+ /* UXGA */
+ { V4L2_DV_BT_DMT_1600X1200P60, 0x96, 0x00 },
+};
+
+static void adv748x_hdmi_fill_format(struct adv748x_hdmi *hdmi,
+ struct v4l2_mbus_framefmt *fmt)
+{
+ memset(fmt, 0, sizeof(*fmt));
+
+ fmt->code = MEDIA_BUS_FMT_RGB888_1X24;
+ fmt->field = hdmi->timings.bt.interlaced ?
+ V4L2_FIELD_INTERLACED : V4L2_FIELD_NONE;
INTERLACED -> ALTERNATE.
+
+ /* The colorspace depends on the AVI InfoFrame contents */
+ fmt->colorspace = V4L2_COLORSPACE_SRGB;
+
+ fmt->width = hdmi->timings.bt.width;
+ fmt->height = hdmi->timings.bt.height;
+}
+
+static void adv748x_fill_optional_dv_timings(struct v4l2_dv_timings *timings)
+{
+ v4l2_find_dv_timings_cap(timings, &adv748x_hdmi_timings_cap,
+ 250000, NULL, NULL);
+}
+
+static bool adv748x_hdmi_has_signal(struct adv748x_state *state)
+{
+ int val;
+
+ /* Check that VERT_FILTER and DE_REGEN is locked */
+ val = hdmi_read(state, ADV748X_HDMI_LW1);
+ return (val & ADV748X_HDMI_LW1_VERT_FILTER) &&
+ (val & ADV748X_HDMI_LW1_DE_REGEN);
+}
+
+static int adv748x_hdmi_read_pixelclock(struct adv748x_state *state)
+{
+ int a, b;
+
+ a = hdmi_read(state, ADV748X_HDMI_TMDS_1);
+ b = hdmi_read(state, ADV748X_HDMI_TMDS_2);
+ if (a < 0 || b < 0)
+ return -ENODATA;
+
+ /*
+ * The high 9 bits store TMDS frequency measurement in MHz
+ * The low 7 bits of TMDS_2 store the 7-bit TMDS fractional frequency
+ * measurement in 1/128 MHz
+ */
+ return ((a << 1) | (b >> 7)) * 1000000 + (b & 0x7f) * 1000000 / 128;
+}
+
+/*
+ * adv748x_hdmi_set_de_timings: Adjust horizontal picture offset through DE
+ *
+ * HDMI CP uses a Data Enable synchronisation timing reference
+ *
+ * Vary the leading and trailing edge position of the DE signal output by the CP
+ * core. Values are stored as signed-twos-complement in one-pixel-clock units
+ *
+ * The start and end are shifted equally by the 10-bit shift value.
+ */
+static void adv748x_hdmi_set_de_timings(struct adv748x_state *state, int shift)
+{
+ u8 high, low;
+
+ /* POS_HIGH stores bits 8 and 9 of both the start and end */
+ high = ADV748X_CP_DE_POS_HIGH_SET;
+ high |= (shift & 0x300) >> 8;
+ low = shift & 0xff;
+
+ /* The sequence of the writes is important and must be followed */
+ cp_write(state, ADV748X_CP_DE_POS_HIGH, high);
+ cp_write(state, ADV748X_CP_DE_POS_END_LOW, low);
+
+ high |= (shift & 0x300) >> 6;
+
+ cp_write(state, ADV748X_CP_DE_POS_HIGH, high);
+ cp_write(state, ADV748X_CP_DE_POS_START_LOW, low);
+}
+
+static int adv748x_hdmi_set_video_timings(struct adv748x_state *state,
+ const struct v4l2_dv_timings *timings)
+{
+ const struct adv748x_hdmi_video_standards *stds =
+ adv748x_hdmi_video_standards;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(adv748x_hdmi_video_standards); i++) {
+ if (!v4l2_match_dv_timings(timings, &stds[i].timings, 250000,
+ false))
+ continue;
+ }
+
+ if (i >= ARRAY_SIZE(adv748x_hdmi_video_standards))
+ return -EINVAL;
+
+ /*
+ * When setting cp_vid_std to either 720p, 1080i, or 1080p, the video
+ * will get shifted horizontally to the left in active video mode.
+ * The de_h_start and de_h_end controls are used to centre the picture
+ * correctly
+ */
+ switch (stds[i].vid_std) {
+ case 0x53: /* 720p */
+ adv748x_hdmi_set_de_timings(state, -40);
+ break;
+ case 0x54: /* 1080i */
+ case 0x5e: /* 1080p */
+ adv748x_hdmi_set_de_timings(state, -44);
+ break;
+ default:
+ adv748x_hdmi_set_de_timings(state, 0);
+ break;
+ }
+
+ io_write(state, ADV748X_IO_VID_STD, stds[i].vid_std);
+ io_clrset(state, ADV748X_IO_DATAPATH, ADV748X_IO_DATAPATH_VFREQ_M,
+ stds[i].v_freq << ADV748X_IO_DATAPATH_VFREQ_SHIFT);
+
+ return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * v4l2_subdev_video_ops
+ */
+
+static int adv748x_hdmi_s_dv_timings(struct v4l2_subdev *sd,
+ struct v4l2_dv_timings *timings)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+ int ret;
+
+ if (!timings)
+ return -EINVAL;
+
+ if (v4l2_match_dv_timings(&hdmi->timings, timings, 0, false))
+ return 0;
+
+ if (!v4l2_valid_dv_timings(timings, &adv748x_hdmi_timings_cap,
+ NULL, NULL))
+ return -ERANGE;
+
+ adv748x_fill_optional_dv_timings(timings);
+
+ mutex_lock(&state->mutex);
+
+ ret = adv748x_hdmi_set_video_timings(state, timings);
+ if (ret)
+ goto error;
+
+ hdmi->timings = *timings;
+
+ cp_clrset(state, ADV748X_CP_VID_ADJ_2, ADV748X_CP_VID_ADJ_2_INTERLACED,
+ timings->bt.interlaced ?
+ ADV748X_CP_VID_ADJ_2_INTERLACED : 0);
+
+ mutex_unlock(&state->mutex);
+
+ return 0;
+
+error:
+ mutex_unlock(&state->mutex);
+ return ret;
+}
+
+static int adv748x_hdmi_g_dv_timings(struct v4l2_subdev *sd,
+ struct v4l2_dv_timings *timings)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+
+ mutex_lock(&state->mutex);
+
+ *timings = hdmi->timings;
+
+ mutex_unlock(&state->mutex);
+
+ return 0;
+}
+
+static int adv748x_hdmi_query_dv_timings(struct v4l2_subdev *sd,
+ struct v4l2_dv_timings *timings)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+ struct v4l2_bt_timings *bt = &timings->bt;
+ int pixelclock;
+ int polarity;
+
+ if (!timings)
+ return -EINVAL;
+
+ memset(timings, 0, sizeof(struct v4l2_dv_timings));
+
+ if (!adv748x_hdmi_has_signal(state))
+ return -ENOLINK;
+
+ pixelclock = adv748x_hdmi_read_pixelclock(state);
+ if (pixelclock < 0)
+ return -ENODATA;
+
+ timings->type = V4L2_DV_BT_656_1120;
+
+ bt->pixelclock = pixelclock;
+ bt->interlaced = hdmi_read(state, ADV748X_HDMI_F1H1) &
+ ADV748X_HDMI_F1H1_INTERLACED ?
+ V4L2_DV_INTERLACED : V4L2_DV_PROGRESSIVE;
+ bt->width = hdmi_read16(state, ADV748X_HDMI_LW1,
+ ADV748X_HDMI_LW1_WIDTH_MASK);
+ bt->height = hdmi_read16(state, ADV748X_HDMI_F0H1,
+ ADV748X_HDMI_F0H1_HEIGHT_MASK);
+ bt->hfrontporch = hdmi_read16(state, ADV748X_HDMI_HFRONT_PORCH,
+ ADV748X_HDMI_HFRONT_PORCH_MASK);
+ bt->hsync = hdmi_read16(state, ADV748X_HDMI_HSYNC_WIDTH,
+ ADV748X_HDMI_HSYNC_WIDTH_MASK);
+ bt->hbackporch = hdmi_read16(state, ADV748X_HDMI_HBACK_PORCH,
+ ADV748X_HDMI_HBACK_PORCH_MASK);
+ bt->vfrontporch = hdmi_read16(state, ADV748X_HDMI_VFRONT_PORCH,
+ ADV748X_HDMI_VFRONT_PORCH_MASK) / 2;
+ bt->vsync = hdmi_read16(state, ADV748X_HDMI_VSYNC_WIDTH,
+ ADV748X_HDMI_VSYNC_WIDTH_MASK) / 2;
+ bt->vbackporch = hdmi_read16(state, ADV748X_HDMI_VBACK_PORCH,
+ ADV748X_HDMI_VBACK_PORCH_MASK) / 2;
+
+ polarity = hdmi_read(state, 0x05);
+ bt->polarities = (polarity & BIT(4) ? V4L2_DV_VSYNC_POS_POL : 0) |
+ (polarity & BIT(5) ? V4L2_DV_HSYNC_POS_POL : 0);
+
+ if (bt->interlaced == V4L2_DV_INTERLACED) {
+ bt->height += hdmi_read16(state, 0x0b, 0x1fff);
+ bt->il_vfrontporch = hdmi_read16(state, 0x2c, 0x3fff) / 2;
+ bt->il_vsync = hdmi_read16(state, 0x30, 0x3fff) / 2;
+ bt->il_vbackporch = hdmi_read16(state, 0x34, 0x3fff) / 2;
+ }
+
+ adv748x_fill_optional_dv_timings(timings);
+
+ /*
+ * No interrupt handling is implemented yet.
+ * There should be an IRQ when a cable is plugged and the new timings
+ * should be figured out and stored to state.
+ */
+ hdmi->timings = *timings;
+
+ return 0;
+}
+
+static int adv748x_hdmi_g_input_status(struct v4l2_subdev *sd, u32 *status)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+
+ mutex_lock(&state->mutex);
+
+ *status = adv748x_hdmi_has_signal(state) ? 0 : V4L2_IN_ST_NO_SIGNAL;
+
+ mutex_unlock(&state->mutex);
+
+ return 0;
+}
+
+static int adv748x_hdmi_s_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+ int ret;
+
+ mutex_lock(&state->mutex);
+
+ ret = adv748x_txa_power(state, enable);
+ if (ret)
+ goto done;
+
+ if (adv748x_hdmi_has_signal(state))
+ adv_dbg(state, "Detected HDMI signal\n");
+ else
+ adv_dbg(state, "Couldn't detect HDMI video signal\n");
+
+done:
+ mutex_unlock(&state->mutex);
+ return ret;
+}
+
+static int adv748x_hdmi_g_pixelaspect(struct v4l2_subdev *sd,
+ struct v4l2_fract *aspect)
+{
+ aspect->numerator = 1;
+ aspect->denominator = 1;
+
+ return 0;
+}
+
+static const struct v4l2_subdev_video_ops adv748x_video_ops_hdmi = {
+ .s_dv_timings = adv748x_hdmi_s_dv_timings,
+ .g_dv_timings = adv748x_hdmi_g_dv_timings,
+ .query_dv_timings = adv748x_hdmi_query_dv_timings,
+ .g_input_status = adv748x_hdmi_g_input_status,
+ .s_stream = adv748x_hdmi_s_stream,
+ .g_pixelaspect = adv748x_hdmi_g_pixelaspect,
+};
+
+/* -----------------------------------------------------------------------------
+ * v4l2_subdev_pad_ops
+ */
+
+static int adv748x_hdmi_propagate_pixelrate(struct adv748x_hdmi *hdmi)
+{
+ struct v4l2_subdev *tx;
+ struct v4l2_dv_timings timings;
+ struct v4l2_bt_timings *bt = &timings.bt;
+ unsigned int fps;
+
+ tx = adv748x_get_remote_sd(&hdmi->pads[ADV748X_HDMI_SOURCE]);
+ if (!tx)
+ return -ENOLINK;
+
+ adv748x_hdmi_query_dv_timings(&hdmi->sd, &timings);
+
+ fps = DIV_ROUND_CLOSEST_ULL(bt->pixelclock,
+ V4L2_DV_BT_FRAME_WIDTH(bt) *
+ V4L2_DV_BT_FRAME_HEIGHT(bt));
+
+ return adv748x_csi2_set_pixelrate(tx, bt->width * bt->height * fps);
+}
+
+static int adv748x_hdmi_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index != 0)
+ return -EINVAL;
+
+ code->code = MEDIA_BUS_FMT_RGB888_1X24;
+
+ return 0;
+}
+
+static int adv748x_hdmi_get_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *sdformat)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct v4l2_mbus_framefmt *mbusformat;
+
+ if (sdformat->pad != ADV748X_HDMI_SOURCE)
+ return -EINVAL;
+
+ if (sdformat->which == V4L2_SUBDEV_FORMAT_TRY) {
+ mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad);
+ sdformat->format = *mbusformat;
+ } else {
+ adv748x_hdmi_fill_format(hdmi, &sdformat->format);
+ adv748x_hdmi_propagate_pixelrate(hdmi);
+ }
+
+ return 0;
+}
+
+static int adv748x_hdmi_set_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *sdformat)
+{
+ struct v4l2_mbus_framefmt *mbusformat;
+
+ if (sdformat->pad != ADV748X_HDMI_SOURCE)
+ return -EINVAL;
+
+ if (sdformat->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+ return adv748x_hdmi_get_format(sd, cfg, sdformat);
+
+ mbusformat = v4l2_subdev_get_try_format(sd, cfg, sdformat->pad);
+ *mbusformat = sdformat->format;
+
+ return 0;
+}
+
+static int adv748x_hdmi_get_edid(struct v4l2_subdev *sd, struct v4l2_edid *edid)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+
+ memset(edid->reserved, 0, sizeof(edid->reserved));
+
+ if (!hdmi->edid.present)
+ return -ENODATA;
+
+ if (edid->start_block == 0 && edid->blocks == 0) {
+ edid->blocks = hdmi->edid.blocks;
+ return 0;
+ }
+
+ if (edid->start_block >= hdmi->edid.blocks)
+ return -EINVAL;
+
+ if (edid->start_block + edid->blocks > hdmi->edid.blocks)
+ edid->blocks = hdmi->edid.blocks - edid->start_block;
+
+ memcpy(edid->edid, hdmi->edid.edid + edid->start_block * 128,
+ edid->blocks * 128);
+
+ return 0;
+}
+
+static inline int adv748x_hdmi_edid_write_block(struct adv748x_hdmi *hdmi,
+ unsigned int total_len, const u8 *val)
+{
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+ int err = 0;
+ int i = 0;
+ int len = 0;
+
+ adv_dbg(state, "%s: write EDID block (%d byte)\n",
+ __func__, total_len);
+
+ while (!err && i < total_len) {
+ len = (total_len - i) > I2C_SMBUS_BLOCK_MAX ?
+ I2C_SMBUS_BLOCK_MAX :
+ (total_len - i);
+
+ err = adv748x_write_block(state, ADV748X_PAGE_EDID,
+ i, val + i, len);
+ i += len;
+ }
+
+ return err;
+}
+
+static int adv748x_hdmi_set_edid(struct v4l2_subdev *sd, struct v4l2_edid *edid)
+{
+ struct adv748x_hdmi *hdmi = adv748x_sd_to_hdmi(sd);
+ struct adv748x_state *state = adv748x_hdmi_to_state(hdmi);
+ int err;
+
+ memset(edid->reserved, 0, sizeof(edid->reserved));
+
+ if (edid->start_block != 0)
+ return -EINVAL;
+
+ if (edid->blocks == 0) {
+ hdmi->edid.blocks = 0;
+ hdmi->edid.present = 0;
+
+ /* Fall back to a 16:9 aspect ratio */
+ hdmi->aspect_ratio.numerator = 16;
+ hdmi->aspect_ratio.denominator = 9;
+
+ /* Disable the EDID */
+ repeater_write(state, ADV748X_REPEATER_EDID_SZ,
+ edid->blocks << ADV748X_REPEATER_EDID_SZ_SHIFT);
+
+ repeater_write(state, ADV748X_REPEATER_EDID_CTL, 0);
+
+ return 0;
+ }
+
+ if (edid->blocks > 4) {
+ edid->blocks = 4;
+ return -E2BIG;
+ }
+
+ memcpy(hdmi->edid.edid, edid->edid, 128 * edid->blocks);
+ hdmi->edid.blocks = edid->blocks;
+ hdmi->edid.present = true;
+
+ hdmi->aspect_ratio = v4l2_calc_aspect_ratio(edid->edid[0x15],
+ edid->edid[0x16]);
+
+ err = adv748x_hdmi_edid_write_block(hdmi, 128 * edid->blocks,
+ hdmi->edid.edid);
+ if (err < 0) {
+ v4l2_err(sd, "error %d writing edid pad %d\n", err, edid->pad);
+ return err;
+ }
+
+ repeater_write(state, ADV748X_REPEATER_EDID_SZ,
+ edid->blocks << ADV748X_REPEATER_EDID_SZ_SHIFT);
+
+ repeater_write(state, ADV748X_REPEATER_EDID_CTL,
+ ADV748X_REPEATER_EDID_CTL_EN);
+
+ return 0;
+}
The new EDID code looks good! Thank you for doing this.
Regards,
Hans
