Hi Kieran,
Thank you for the patch.
On Wednesday 14 Jun 2017 20:58:13 Kieran Bingham wrote:
> From: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
>
> The Salvator boards use an ADV7482 receiver for HDMI and CVBS inputs.
>
> Provide ADV7482 node on the i2c4 bus, along with connectors for the
> hdmi and cvbs inputs, and link to the csi20 and csi40 nodes as outputs.
>
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
>
> v4:
> - dt: Rebase to dts/renesas/salvator-x.dtsi
> - dt: Use AIN0-7 rather than AIN1-8
>
> v5:
> - dt: Move to salvator-common.dtsi
> ---
> arch/arm64/boot/dts/renesas/salvator-common.dtsi | 123 ++++++++++++++++-
> 1 file changed, 123 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
> b/arch/arm64/boot/dts/renesas/salvator-common.dtsi index
> aef35e0b685a..d74fb55c38bc 100644
> --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
> +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
> @@ -65,6 +65,27 @@
> enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
> };
>
> + cvbs-in {
> + compatible = "composite-video-connector";
> + label = "CVBS IN";
> +
> + port {
> + cvbs_con: endpoint {
> + };
> + };
> + };
> +
> + hdmi-in {
> + compatible = "hdmi-connector";
> + label = "HDMI IN";
> + type = "a";
> +
> + port {
> + hdmi_in_con: endpoint {
> + };
> + };
> + };
> +
> reg_1p8v: regulator0 {
> compatible = "regulator-fixed";
> regulator-name = "fixed-1.8V";
> @@ -257,6 +278,59 @@
> };
> };
>
> +&csi20 {
> + status = "okay";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
Aren't #address-cells, #size-cells and reg already present in the SoC .dtsi ?
And if they're not, shouldn't they be ? :-)
> + csi20_in: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1>;
> + remote-endpoint = <&adv7482_txb>;
> + };
> + };
> + };
> +};
> +
> +&csi40 {
> + status = "okay";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + csi40_in: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1 2 3 4>;
> + remote-endpoint = <&adv7482_txa>;
> + };
> + };
> + };
> +};
> +
> +&cvbs_con {
> + port {
> + cvbs_in: endpoint {
> + remote-endpoint = <&adv7482_ain7>;
> + };
> + };
> +};
You could merge this with the cvbs_con node above.
Apart from that the patch looks good to me.
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> +&hdmi_in_con {
> + port {
> + hdmi_in: endpoint {
> + remote-endpoint = <&adv7482_hdmi>;
> + };
> + };
> +};
> +
> &du {
> pinctrl-0 = <&du_pins>;
> pinctrl-names = "default";
> @@ -343,6 +417,55 @@
>
> shunt-resistor-micro-ohms = <5000>;
> };
> +
> + video-receiver@70 {
> + compatible = "adi,adv7482";
> + reg = <0x70>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + interrupt-parent = <&gpio6>;
> + interrupt-names = "intrq1", "intrq2";
> + interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
> + <31 IRQ_TYPE_LEVEL_LOW>;
> +
> + port@7 {
> + reg = <7>;
> +
> + adv7482_ain7: endpoint {
> + remote-endpoint = <&cvbs_in>;
> + };
> + };
> +
> + port@8 {
> + reg = <8>;
> +
> + adv7482_hdmi: endpoint {
> + remote-endpoint = <&hdmi_in>;
> + };
> + };
> +
> + port@10 {
> + reg = <10>;
> +
> + adv7482_txa: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1 2 3 4>;
> + remote-endpoint = <&csi40_in>;
> + };
> + };
> +
> + port@11 {
> + reg = <11>;
> +
> + adv7482_txb: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1>;
> + remote-endpoint = <&csi20_in>;
> + };
> + };
> + };
> };
>
> &i2c_dvfs {
--
Regards,
Laurent Pinchart
