Hello, this is 6th round of RZ/A1 pin controller patch series. Where did we stop: discussion from pin controller driver shifted toward two new generic pin configuration properties I added to the previous series (bi-directional and output-enable). After a really long discussion, we decided to go for handling internally all bi-directional use cases, making the generic property not a requirement for the series. Interestingly, we recently found out the number of pins actually requiring this flag is less (~half) than what reported by the processor manual, so we could have handled these internally from day one :( We also now manage internally pins requiring IO direction specified in software even when configured in alternate function mode (SWIO mode). Most of them are handled by the driver, some of them have to come from DTS as the user can freely select if they have to be inputs or outputs. For those pins, and after another discussion involving NXP developers, we decided to use input-enable and output-enable properties. I have just sent a patch to add output-enable to the generic pin configuration properties, but it is currently under discussion. However, none of the pins currently configured by mainline DTS require those properties to be specified, so I have dropped in this driver any dependency on output-enable property, and I'm using instead the already in place PIN_CONFIG_OUTPUT one. Once output-enable will eventually be accepted, we can update the driver to make use of it, but since there are no use cases for that at the moment, it makes not too much sense holding this series back for that. The total memory occupation we were so worried about of bi-directional and swio pin tables is now around 100 bytes, because of how the number of pins actually needing those flags has reduced and because of how we have arranged the tables using bitfield structures (credits to Geert here). Having cleared out dependencies on new pin configuration properties and having made configuration flags a driver specific issue, I hope this version can be accepted and land in forthcoming pull request for Renesas PFC updates from Geert, pending some feedback from the linux-gpio community. Thanks j v1 -> v2: - change pin configuration flags as suggested by Chris - gpio set direction function fixed as suggested by Chris - add some more example on pin configuration flag usage to dt-binding doc - fix gpio-controller names to remove unit address as suggested by Geert - some comments chopped here and there to make the driver less verbose v2 -> v3: - fix grammar and syntax in comment and documentation - fix code style (reverse xmas tree ordering in variable declaration) - use irqsave/irqrestore in spinlock lock/unlock - use devm_ version of kasprintf (memory returned was not properly free) - use bitops.h operation ffs and fls to make sure a single bit is set in pmx mask - Add Geert's reviewed-by to DTS patches v3 -> v4: - use "pinmux" property in pmx sub-nodes in place of "renesas,pins" - use pinconf standard properties to set pin mux additional flags - add "bi-directional" and "output-enable" to pinconf generic properties - perform pmx function parsing at dt_node_to_map() time - change DT bindings to use GENERIC_PINCONF - change DT bindings to allow sub-nodes to have "pinmux" property specified - several renames (register names, DT parse functions, set_mux() function) v4 -> v5: - use pinctrl_enable() function in pin controller registration function - update bindings documentation to incorporate Geert's comments - add generic properties unpack macros v5 -> v6: - add tables in driver to manage bi-directional and swio flags - drop dependecies on new generic pin configuration properties Jacopo Mondi (8): pinctrl: Renesas RZ/A1 pin and gpio controller dt-bindings: pinctrl: Add RZ/A1 bindings doc arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header arm: dts: r7s72100: Add pin controller node arm: dts: genmai: Add SCIF2 pin group arm: dts: genmai: Add RIIC2 pin group arm: dts: genmai: Add user led device nodes arm: dts: genmai: Add ethernet pin group .../bindings/pinctrl/renesas,rza1-pinctrl.txt | 218 ++++ arch/arm/boot/dts/r7s72100-genmai.dts | 69 ++ arch/arm/boot/dts/r7s72100.dtsi | 78 ++ drivers/pinctrl/Kconfig | 11 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-rza1.c | 1309 ++++++++++++++++++++ include/dt-bindings/pinctrl/r7s72100-pinctrl.h | 16 + 7 files changed, 1702 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt create mode 100644 drivers/pinctrl/pinctrl-rza1.c create mode 100644 include/dt-bindings/pinctrl/r7s72100-pinctrl.h -- 2.7.4
