Hi Ramesh, On Tue, May 09, 2017 at 02:37:33PM +0100, Ramesh Shanmugasundaram wrote: > Add device tree binding documentation for MAX2175 RF to bits tuner > device. > > Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@xxxxxxxxxxxxxx> > Acked-by: Rob Herring <robh@xxxxxxxxxx> > --- > v5: > - pF in property-units.txt is renamed to pico-farads (Geert) > - "maxim,refout-load-pF" is renamed to "maxim,refout-load". > --- > .../devicetree/bindings/media/i2c/max2175.txt | 61 ++++++++++++++++++++++ > .../devicetree/bindings/property-units.txt | 1 + > 2 files changed, 62 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/max2175.txt > > diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt > new file mode 100644 > index 000000000000..dce421857efe > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt > @@ -0,0 +1,61 @@ > +Maxim Integrated MAX2175 RF to Bits tuner > +----------------------------------------- > + > +The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with > +RF to Bits® front-end designed for software-defined radio solutions. > + > +Required properties: > +-------------------- > +- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner. > +- clocks: phandle to the fixed xtal clock. How about "clock specifier" > +- clock-names: name of the fixed xtal clock, shall be "xtal". If you have a single clock you could drop clock-names. You can obtain it in the driver using clk_get(dev, NULL) . Up to you. > +- port: child port node corresponding to the I2S output, in accordance with > + the video interface bindings defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt. The port > + node must contain at least one endpoint. > + > +Optional properties: > +-------------------- > +- maxim,master : phandle to the master tuner if it is a slave. This > + is used to define two tuners in diversity mode > + (1 master, 1 slave). By default each tuner is an > + individual master. > +- maxim,refout-load : load capacitance value (in pico-farads) on reference > + output drive level. The possible load values are: > + 0 (default - refout disabled) > + 10 > + 20 > + 30 > + 40 > + 60 > + 70 > +- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used > + in this hardware for AM antenna input. > + > +Example: > +-------- > + > +Board specific DTS file > + > +/* Fixed XTAL clock node */ > +maxim_xtal: clock { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <36864000>; > +}; > + > +/* A tuner device instance under i2c bus */ > +max2175_0: tuner@60 { > + compatible = "maxim,max2175"; > + reg = <0x60>; > + clocks = <&maxim_xtal>; > + clock-names = "xtal"; > + maxim,refout-load = <10>; > + > + port { > + max2175_0_ep: endpoint { > + remote-endpoint = <&slave_rx_device>; > + }; > + }; > + > +}; > diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt > index 0849618a9df0..2d1d28843c96 100644 > --- a/Documentation/devicetree/bindings/property-units.txt > +++ b/Documentation/devicetree/bindings/property-units.txt > @@ -30,6 +30,7 @@ Electricity > -micro-ohms : micro Ohms > -microwatt-hours: micro Watt-hours > -microvolt : micro volts > +-pico-farads : picofarads Why pico-farads and not picofarads? Most of the existing definitions have no dash. (Just wondering.) -- Kind regards, Sakari Ailus sakari.ailus@xxxxxxxxxxxxxxx