Re: [PATCH v4 0/9] drm: bridge: dw-hdmi: Refactor PHY support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 03/01/2017 11:39 PM, Laurent Pinchart wrote:
> Hello,
> 
> This patch series refactors all the PHY handling code in order to allow
> support of vendor PHYs and Synopsys DWC HDMI 2.0 TX PHYs.
> 
> The series starts with a few cleanups and small fixes. Patch 1/9 just removes
> unused code, patch 2/9 moves the color converter code out of the PHY configure
> function as it isn't PHY-dependent, and patch 3/9 enables color conversion
> even for DVI as it is needed to output RGB when the input format is YUV.
> 
> The next two patches fix the power down (4/9) and up (5/9) sequences to comply
> with the HDMI TX PHY specifications. They are the biggest functional changes
> in the whole set, and have been tested successfully (with the rest of the
> series) on i.MX6Q and R-Car H3. I'll try to perform tests on RK3288 tomorrow
> if nobody beats me to it (Neil, that's for you :-)). 

Done !

Tested on RK3288 on ACT8846 EVB Board and Amlogic S905X P230 Board.

Tested-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>

Thanks,
Neil

> The PLL PHY lock delay
> has been measured to be between 300µs and 350µs on R-Car H3 and between 400µs
> and 600µs on i.MX6Q. The PHY power down delay has been measured to be less
> than 50µs on both platforms, and was often close to instant with power down
> reported in the first poll iteration. We should thus be more than safe with a
> 5ms timeout.
> 
> Patch 6/9 breaks the PHY operations out. Glue code is then allowed to pass a
> PHY operations structure to support vendor PHYs. The existing PHY support code
> is turned into a default Synopsys PHYs implementation for those PHY
> operations.
> 
> Patch 7/9 further refactors the Synopsys PHY configuration function to make
> it modular, in order to support DWC HDMI 2.0 TX PHYs that have a very
> different register layout compared to the currently supported PHYs. Glue code
> is again allowed to provide a custom PHY configuration implementation, with
> the existing PHY support code turned into the default implementation for all
> currently supported Synopsys PHYs.
> 
> Patch 8/9 is a small cleanup that removes the now unneeded device type for
> glue code platform data, and patch 9/9 follows by switching the driver to
> regmap in order to support vendor-specific register access more easily.
> 
> Kieran Bingham (2):
>   drm: bridge: dw-hdmi: Add support for custom PHY configuration
>   drm: bridge: dw-hdmi: Remove device type from platform data
> 
> Laurent Pinchart (5):
>   drm: bridge: dw-hdmi: Remove unused functions
>   drm: bridge: dw-hdmi: Move CSC configuration out of PHY code
>   drm: bridge: dw-hdmi: Fix the PHY power down sequence
>   drm: bridge: dw-hdmi: Fix the PHY power up sequence
>   drm: bridge: dw-hdmi: Create PHY operations
> 
> Neil Armstrong (2):
>   drm: bridge: dw-hdmi: Enable CSC even for DVI
>   drm: bridge: dw-hdmi: Switch to regmap for register access
> 
>  drivers/gpu/drm/bridge/dw-hdmi.c            | 467 +++++++++++++++++-----------
>  drivers/gpu/drm/imx/dw_hdmi-imx.c           |   2 -
>  drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c |   1 -
>  include/drm/bridge/dw_hdmi.h                |  33 +-
>  4 files changed, 304 insertions(+), 199 deletions(-)
> 




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux