On Sat, Jan 21, 2017 at 03:42:11PM +0100, Marek Vasut wrote: > Add DT bindings for the Renesas RCar GyroADC block. This block is > a simple 4/8-channel ADC which samples 12/15/24 bits of data every > cycle from all channels. Isn't this v7? > > Signed-off-by: Marek Vasut <marek.vasut@xxxxxxxxx> > Cc: Geert Uytterhoeven <geert+renesas@xxxxxxxxx> > Cc: Simon Horman <horms+renesas@xxxxxxxxxxxx> > Cc: Jonathan Cameron <jic23@xxxxxxxxxx> > Cc: linux-renesas-soc@xxxxxxxxxxxxxxx > Cc: Wolfram Sang <wsa@xxxxxxxxxxxxx> > Cc: Rob Herring <robh@xxxxxxxxxx> > Cc: devicetree@xxxxxxxxxxxxxxx > --- > .../bindings/iio/adc/renesas,gyroadc.txt | 93 ++++++++++++++++++++++ > 1 file changed, 93 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt > > diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt > new file mode 100644 > index 000000000000..081947367135 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt > @@ -0,0 +1,93 @@ > +* Renesas RCar GyroADC device driver What's a GyroADC? > + > +Required properties: > +- compatible: Should be "renesas,<chip>-gyroadc", "renesas,rcar-gyroadc". Need to enumerate <chip>. > + Use "renesas,r8a7792-gyroadc" for a GyroADC with interrupt > + block found in R8A7792. > +- reg: Address and length of the register set for the device > +- clocks: References to all the clocks specified in the clock-names > + property as specified in > + Documentation/devicetree/bindings/clock/clock-bindings.txt. > +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block > + clock, the "if" is the interface clock. > +- power-domains: Must contain a reference to the PM domain, if available. > +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs > + except for "fujitsu,mb88101a". Should be <0> (setting for > + only subnode) for "fujitsu,mb88101a". > +- #size-cells: Should be <0> (setting for the subnodes) > + > +Sub-nodes: > +Optionally you can define subnodes which select the connected ADC type and > +reference voltage for the GyroADC channels. Seems strange to be optional. How many nodes are possible? > + > +Required properties for subnodes: > +- compatible: Should be either of: > + "fujitsu,mb88101a" > + - Fujitsu MB88101A compatible mode, > + 12bit sampling, up to 4 channels can be sampled in > + round-robin fashion. One Fujitsu chip supplies four > + GyroADC channels with data as it contains four ADCs > + on the chip and thus for 4-channel operation, single > + MB88101A is required. The Cx chipselect lines of the > + MB88101A connect directly to two CHS lines of the > + GyroADC, no demuxer is required. The data out line > + of each MB88101A connects to a shared input pin of > + the GyroADC. > + "ti,adcs7476" or "ti,adc121" or "adi,ad7476" > + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, > + 15bit sampling, up to 8 channels can be sampled in > + round-robin fashion. One TI/ADI chip supplies single > + ADC channel with data, thus for 8-channel operation, > + 8 chips are required. A 3:8 chipselect demuxer is > + required to connect the nCS line of the TI/ADI chips > + to the GyroADC, while MISO line of each TI/ADI ADC > + connects to a shared input pin of the GyroADC. > + "maxim,max1162" or "maxim,max11100" > + - Maxim MAX1162 / Maxim MAX11100 compatible mode, > + 16bit sampling, up to 8 channels can be sampled in > + round-robin fashion. One Maxim chip supplies single > + ADC channel with data, thus for 8-channel operation, > + 8 chips are required. A 3:8 chipselect demuxer is > + required to connect the nCS line of the MAX chips > + to the GyroADC, while MISO line of each Maxim ADC > + connects to a shared input pin of the GyroADC. > +- reg: Should be the number of the analog input. Should be present > + for all ADCs except "fujitsu,mb88101a". > +- vref-supply: Reference to the channel reference voltage regulator. > + > +Example: > + vref_max1162: regulator-vref-max1162 { > + compatible = "regulator-fixed"; > + > + regulator-name = "MAX1162 Vref"; > + regulator-min-microvolt = <4096000>; > + regulator-max-microvolt = <4096000>; > + }; > + > + &adc { > + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; > + reg = <0 0xe6e54000 0 64>; > + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; > + clock-names = "fck", "if"; > + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; > + > + pinctrl-0 = <&adc_pins>; > + pinctrl-names = "default"; > + > + status = "okay"; Drop status from examples. > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc@0 { > + reg = <0>; > + compatible = "maxim,max1162"; > + vref-supply = <&vref_max1162>; > + }; > + > + adc@1 { > + reg = <1>; > + compatible = "maxim,max1162"; > + vref-supply = <&vref_max1162>; > + }; > + }; > -- > 2.11.0 >