Hi Valentina, On 2024-09-12 12:00 PM, Valentina Fernandez wrote: > Add a dt-binding for the Microchip Inter-Processor Communication (IPC) > mailbox controller. > > Signed-off-by: Valentina Fernandez <valentina.fernandezalanis@xxxxxxxxxxxxx> > --- > .../bindings/mailbox/microchip,sbi-ipc.yaml | 115 ++++++++++++++++++ > 1 file changed, 115 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mailbox/microchip,sbi-ipc.yaml > > diff --git a/Documentation/devicetree/bindings/mailbox/microchip,sbi-ipc.yaml b/Documentation/devicetree/bindings/mailbox/microchip,sbi-ipc.yaml > new file mode 100644 > index 000000000000..dc2cbd5eb28f > --- /dev/null > +++ b/Documentation/devicetree/bindings/mailbox/microchip,sbi-ipc.yaml > @@ -0,0 +1,115 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/mailbox/microchip,sbi-ipc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Microchip Inter-processor communication (IPC) mailbox controller > + > +maintainers: > + - Valentina Fernandez <valentina.fernandezalanis@xxxxxxxxxxxxx> > + > +description: > + The Microchip Inter-processor Communication (IPC) facilitates > + message passing between processors using an interrupt signaling > + mechanism. > + This SBI interface is compatible with the Mi-V Inter-hart > + Communication (IHC) IP. > + The microchip,sbi-ipc compatible string is inteded for use by software > + running in supervisor privileged mode (s-mode). The SoC-specific > + compatibles are inteded for use by the SBI implementation in machine > + mode (m-mode). There is a lot of conditional logic in this binding for how small it is. Would it make sense to split this into two separate bindings? For example, with the current binding microchip,ihc-chan-disabled-mask is allowed for the SBI interface, but doesn't look like it belongs there. > + > +properties: > + compatible: > + enum: > + - microchip,sbi-ipc > + - microchip,miv-ihc-rtl-v2 > + > + reg: > + maxItems: 1 > + > + interrupts: > + minItems: 1 > + maxItems: 5 > + > + interrupt-names: > + minItems: 1 > + maxItems: 5 > + > + "#mbox-cells": > + description: > + For the SBI "device", the cell represents the global "logical" channel IDs. > + The meaning of channel IDs are platform firmware dependent. The > + SoC-specific compatibles are intended for use by the SBI implementation, > + rather than s-mode software. There the cell would represent the physical > + channel and do not vary depending on platform firmware. > + const: 1 > + > + microchip,ihc-chan-disabled-mask: > + description: > + Represents the enable/disable state of the bi-directional IHC channels > + within the MIV-IHC IP configuration. The mask is a 16-bit value, but only > + the first 15 bits are utilized.Each of the bits corresponds to > + one of the 15 IHC channels. > + A bit set to '1' indicates that the corresponding channel is disabled, > + and any read or write operations to that channel will return zero. > + A bit set to '0' indicates that the corresponding channel is enabled > + and will be accessible through its dedicated address range registers. > + The remaining bit of the 16-bit mask is reserved and should be ignored. > + The actual enable/disable state of each channel is determined by the > + IP block’s configuration. > + $ref: /schemas/types.yaml#/definitions/uint16 > + default: 0 > + > +required: > + - compatible > + - interrupts > + - interrupt-names > + - "#mbox-cells" > + > +additionalProperties: false > + > +allOf: > + - if: > + properties: > + compatible: > + contains: > + const: microchip,sbi-ipc > + then: > + properties: > + reg: false > + else: > + required: > + - reg > + > + - if: > + properties: > + compatible: > + contains: > + const: microchip,miv-ihc-rtl-v2 > + then: > + properties: > + interrupt-names: > + items: > + pattern: "^hart-[0-5]+$" The driver in patch 3 uses this pattern for the SBI interface, so should it apply there as well? Regards, Samuel > + > +examples: > + - | > + mailbox { > + compatible = "microchip,sbi-ipc"; > + interrupt-parent = <&plic>; > + interrupts = <180>, <179>, <178>; > + interrupt-names = "hart-1", "hart-2", "hart-3"; > + #mbox-cells = <1>; > + }; > + - | > + mailbox@50000000 { > + compatible = "microchip,miv-ihc-rtl-v2"; > + microchip,ihc-chan-disabled-mask= /bits/ 16 <0>; > + reg = <0x50000000 0x1C000>; > + interrupt-parent = <&plic>; > + interrupts = <180>, <179>, <178>; > + interrupt-names = "hart-1", "hart-2", "hart-3"; > + #mbox-cells = <1>; > + };
