> Subject: Re: [PATCH v2 2/2] remoteproc: imx_rproc: handle system off
> for i.MX7ULP
>
> On Fri, Jul 19, 2024 at 04:49:04PM +0800, Peng Fan (OSS) wrote:
> > From: Peng Fan <peng.fan@xxxxxxx>
> >
> > The i.MX7ULP Cortex-A7 is under control of Cortex-M4. The
> i.MX7ULP
> > Linux poweroff and restart rely on rpmsg driver to send a message to
> > Cortex-M4 firmware. Then Cortex-A7 could poweroff or restart by
> > Cortex-M4 to configure the i.MX7ULP power controller properly.
> >
> > However the reboot and restart kernel common code use atomic
> notifier,
> > so with blocking tx mailbox will trigger kernel dump, because of
> > blocking mailbox will use wait_for_completion_timeout. In such case,
> > linux no need to wait for completion.
> >
> > Current patch is to use non-blocking tx mailbox channel when system
> is
> > going to poweroff or restart.
> >
> > Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
> > ---
> > drivers/remoteproc/imx_rproc.c | 36
> > ++++++++++++++++++++++++++++++++++++
> > 1 file changed, 36 insertions(+)
> >
> > diff --git a/drivers/remoteproc/imx_rproc.c
> > b/drivers/remoteproc/imx_rproc.c index
> 01cf1dfb2e87..e1abf110abc9
> > 100644
> > --- a/drivers/remoteproc/imx_rproc.c
> > +++ b/drivers/remoteproc/imx_rproc.c
> > @@ -18,6 +18,7 @@
> > #include <linux/of_reserved_mem.h>
> > #include <linux/platform_device.h>
> > #include <linux/pm_domain.h>
> > +#include <linux/reboot.h>
> > #include <linux/regmap.h>
> > #include <linux/remoteproc.h>
> > #include <linux/workqueue.h>
> > @@ -114,6 +115,7 @@ struct imx_rproc {
> > u32 entry; /* cpu start
> address */
> > u32 core_index;
> > struct dev_pm_domain_list *pd_list;
> > + struct sys_off_data data;
>
> What is this for? I don't see it used in this patch.
Oh, it was added when I was developing this feature, but in the end
this seems not needed.
>
> > };
> >
> > static const struct imx_rproc_att imx_rproc_att_imx93[] = { @@
> > -1050,6 +1052,22 @@ static int imx_rproc_clk_enable(struct
> imx_rproc *priv)
> > return 0;
> > }
> >
> > +static int imx_rproc_sys_off_handler(struct sys_off_data *data) {
> > + struct rproc *rproc = data->cb_data;
> > + int ret;
> > +
> > + imx_rproc_free_mbox(rproc);
> > +
> > + ret = imx_rproc_xtr_mbox_init(rproc, false);
> > + if (ret) {
> > + dev_err(&rproc->dev, "Failed to request non-blocking
> mbox\n");
> > + return NOTIFY_BAD;
> > + }
> > +
> > + return NOTIFY_DONE;
> > +}
> > +
> > static int imx_rproc_probe(struct platform_device *pdev) {
> > struct device *dev = &pdev->dev;
> > @@ -1104,6 +1122,24 @@ static int imx_rproc_probe(struct
> platform_device *pdev)
> > if (rproc->state != RPROC_DETACHED)
> > rproc->auto_boot = of_property_read_bool(np,
> "fsl,auto-boot");
> >
> > + if (of_device_is_compatible(dev->of_node, "fsl,imx7ulp-cm4"))
> {
> > + ret = devm_register_sys_off_handler(dev,
> SYS_OFF_MODE_POWER_OFF_PREPARE,
> > +
> SYS_OFF_PRIO_DEFAULT,
> > +
> imx_rproc_sys_off_handler, rproc);
>
> Why does the mailbox needs to be set up again when the system is
> going down...
As wrote in commit message:
"i.MX7ULP Linux poweroff and restart rely on rpmsg driver to send a
message," so need to set up mailbox in non-blocking way to send
a message to M4 side.
>
> > + if (ret) {
> > + dev_err(dev, "register power off handler
> failure\n");
> > + goto err_put_clk;
> > + }
> > +
> > + ret = devm_register_sys_off_handler(dev,
> SYS_OFF_MODE_RESTART_PREPARE,
> > +
> SYS_OFF_PRIO_DEFAULT,
> > +
> imx_rproc_sys_off_handler, rproc);
>
> ... and why does it need to be free'd when the system is going up?
Sorry, I not get your point. The free is in imx_rproc_sys_off_handler.
During system booting, the mailbox is not freed.
Thanks,
Peng.
>
> > + if (ret) {
> > + dev_err(dev, "register restart handler
> failure\n");
> > + goto err_put_clk;
> > + }
> > + }
> > +
> > ret = rproc_add(rproc);
> > if (ret) {
> > dev_err(dev, "rproc_add failed\n");
> >
> > --
> > 2.37.1
> >
> >
