On 3/19/24 12:25 AM, Krzysztof Kozlowski wrote:
> On 19/03/2024 02:06, Tanmay Shah wrote:
>>
>>
>> On 3/17/24 1:55 PM, Krzysztof Kozlowski wrote:
>>> On 15/03/2024 22:15, Tanmay Shah wrote:
>>>> AMD-Xilinx Versal and Versal-NET are successor of ZynqMP platform. ZynqMP
>>>> remoteproc driver is mostly compatible with new platforms except few
>>>> platform specific differences.
>>>>
>>>> Versal has same IP of cortex-R5 cores hence maintained compatible string
>>>> same as ZynqMP platform. However, hardcode TCM addresses are not
>>>> supported for new platforms and must be provided in device-tree as per
>>>> new bindings. This makes TCM representation data-driven and easy to
>>>> maintain. This check is provided in the driver.
>>>>
>>>> For Versal-NET platform, TCM doesn't need to be configured in lockstep
>>>> mode or split mode. Hence that call to PMC firmware is avoided in the
>>>> driver for Versal-NET platform.
>>>>
>>>> Signed-off-by: Tanmay Shah <tanmay.shah@xxxxxxx>
>>>> ---
>>>> drivers/remoteproc/xlnx_r5_remoteproc.c | 19 +++++++++++++++----
>>>> 1 file changed, 15 insertions(+), 4 deletions(-)
>>>>
>>>> diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
>>>> index d4a22caebaad..193bc159d1b4 100644
>>>> --- a/drivers/remoteproc/xlnx_r5_remoteproc.c
>>>> +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
>>>> @@ -323,9 +323,12 @@ static int zynqmp_r5_set_mode(struct zynqmp_r5_core *r5_core,
>>>> return ret;
>>>> }
>>>>
>>>> - ret = zynqmp_pm_set_tcm_config(r5_core->pm_domain_id, tcm_mode);
>>>> - if (ret < 0)
>>>> - dev_err(r5_core->dev, "failed to configure TCM\n");
>>>> + /* TCM configuration is not needed in versal-net */
>>>> + if (device_is_compatible(r5_core->dev, "xlnx,zynqmp-r5f")) {
>>>> + ret = zynqmp_pm_set_tcm_config(r5_core->pm_domain_id, tcm_mode);
>>>> + if (ret < 0)
>>>> + dev_err(r5_core->dev, "failed to configure TCM\n");
>>>> + }
>>>>
>>>> return ret;
>>>> }
>>>> @@ -933,10 +936,17 @@ static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster,
>>>> int ret, i;
>>>>
>>>> r5_core = cluster->r5_cores[0];
>>>> +
>>>> + /*
>>>> + * New platforms must use device tree for TCM parsing.
>>>> + * Only ZynqMP uses hardcode TCM.
>>>> + */
>>>> if (of_find_property(r5_core->np, "reg", NULL))
>>>> ret = zynqmp_r5_get_tcm_node_from_dt(cluster);
>>>> - else
>>>> + else if (of_machine_is_compatible("xlnx,zynqmp"))
>>>> ret = zynqmp_r5_get_tcm_node(cluster);
>>>
>>> That's poor code. Your drivers should not depend on platform. I don't
>>> understand why you need to do this and how is even related to this patch.
>>
>> You are correct, ideally this shouldn't be needed. However, this driver contains
>> hardcode TCM addresses that were used before TCM bindings were designed and available in
>> device-tree. This check is provided to maintain backward compatibility with device-tree
>> where TCM isn't expected.
>>
>> For new platforms (Versal and Versal-NET) TCM must be provided in device-tree and for
>> ZynqMP if it's not in device-tree then to maintain backward compatibility hardcode
>> addresses are used.
>
> That does not work like this. You cannot bind to some sort of different
> compatible. If you disagree, please list the compatibles the driver
> binds to.
Okay understood. I believe then removing hardcode addresses makes more sense in that
case. So, driver will become same for all the devices.
>
> Best regards,
> Krzysztof
>
