On 13.02.22 21:12, Suman Anna wrote: > Add support to the K3 R5F remoteproc driver to configure all the R5F > cores to be either in IPC-only mode or the traditional remoteproc mode. > The IPC-only mode expects that the remote processors are already booted > by the bootloader, and only performs the minimum steps required to > initialize and deinitialize the virtio IPC transports. The remoteproc > mode allows the kernel remoteproc driver to do the regular load and > boot and other device management operations for a R5F core. > > The IPC-only mode for a R5F core is detected and configured at driver > probe time by querying the System Firmware for the R5F power and reset > state and/or status and making sure that the R5F core is indeed started > by the bootloaders, otherwise the device is configured for remoteproc > mode. > > Support for IPC-only mode is achieved through .attach(), .detach() and > .get_loaded_rsc_table() callback ops and zeroing out the regular rproc > ops .prepare(), .unprepare(), .start() and .stop(). The resource table > follows a design-by-contract approach and is expected to be at the base > of the DDR firmware region reserved for each remoteproc, it is mostly > expected to contain only the virtio device and trace resource entries. > > NOTE: > The driver cannot configure a R5F core for remoteproc mode by any > means without rebooting the kernel if that R5F core has been started > by a bootloader. This is the current desired behavior and can be > enhanced in the future if the feature is needed. > This change surfaced some complex issue in the K3 core: Turning on the RTI1 watchdog also powers up R5F core 1. And this could happen either in U-Boot or in the kernel. If the kernel finds the core running, it also expects a resource table in the reserved RAM. But as the core is supposed to start via remoteproc, there is none, rather often garbage. Sometimes, a consistency check catches that, but not always: [ 38.372844] remoteproc remoteproc18: 41000000.r5f is available [ 38.380324] platform 41400000.r5f: R5F core may have been powered on by a different host, programmed state (0) != actual state (1) [ 38.394910] platform 41400000.r5f: configured R5F for IPC-only mode [ 38.401941] platform 41400000.r5f: assigned reserved memory node r5f-dma-memory@a1000000 [ 38.476997] remoteproc remoteproc19: 41400000.r5f is available [ 38.484661] remoteproc remoteproc19: attaching to 41400000.r5f [ 38.491092] Unable to handle kernel paging request at virtual address ffff80000dffffff [ 38.503704] Mem abort info: [ 38.509760] ESR = 0x0000000096000007 [ 38.514071] EC = 0x25: DABT (current EL), IL = 32 bits [ 38.519578] SET = 0, FnV = 0 [ 38.523095] EA = 0, S1PTW = 0 [ 38.526355] FSC = 0x07: level 3 translation fault [ 38.528974] cal 6f03000.cal: Neither port is configured, no point in staying up [ 38.531775] Data abort info: [ 38.541866] ISV = 0, ISS = 0x00000007 [ 38.545765] CM = 0, WnR = 0 [ 38.548814] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000082fdc000 [ 38.555831] [ffff80000dffffff] pgd=10000008fffff003, p4d=10000008fffff003, pud=10000008ffffe003, pmd=1000000886609003, pte=0000000000000000 [ 38.568623] remoteproc remoteproc18: powering up 41000000.r5f [ 38.569338] Internal error: Oops: 0000000096000007 [#1] PREEMPT SMP [ 38.574440] remoteproc remoteproc18: Booting fw image am65x-mcu-r5f0_0-fw, size 932 [ 38.580644] Modules linked in: usbserial ti_cal videobuf2_dma_contig ti_k3_r5_remoteproc(+) videobuf2_memops pci_endpoint_test videobuf2_v4l2 rti_wdt watchdog videobuf2_common at24 st_lsm6dsx_i2c(+) optee_rng st_lsm6dsx kfifo_buf pm16d17 rng_core tee_stmm_efi tpm_ftpm_tee fuse dm_mod ip_tables x_tables ipv6 [ 38.589862] remoteproc remoteproc18: remote processor 41000000.r5f is now up [ 38.615533] CPU: 1 PID: 283 Comm: (udev-worker) Not tainted 6.1.54-cip6 #1 [ 38.615546] Hardware name: SIMATIC IOT2050 Advanced PG2 (DT) [ 38.615553] pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 38.641945] pc : rproc_handle_resources.constprop.0+0x8c/0x164 [ 38.647788] lr : rproc_boot+0x2fc/0x57c [ 38.651628] sp : ffff800009d53740 [ 38.654934] x29: ffff800009d53740 x28: ffff00087f7d77f8 x27: ffff0008048f4c10 [ 38.662068] x26: 0000000000000001 x25: ffffffffffffffff x24: ffff80000e000000 [ 38.669199] x23: ffff00080227e038 x22: 0000000000000000 x21: ffff8000092bb1b0 [ 38.676333] x20: ffff00080227e000 x19: 0000000000000000 x18: 000000000000028e [ 38.683464] x17: 0000000000000000 x16: 000000006d958cac x15: ffffffffffffffff [ 38.690597] x14: ffffffffffffffff x13: ffffffffffffffff x12: ffffffffffffffff [ 38.697728] x11: ffffffffffffffff x10: ffffffffffffffff x9 : ffffffffbfffffff [ 38.704862] x8 : ffffffffffffffff x7 : fffffdffffffffff x6 : ffffffffffdfffff [ 38.711994] x5 : ffff000802be1f00 x4 : ffff80000e000100 x3 : 00000000000000fd [ 38.719127] x2 : 00000000ffffffff x1 : ffff80000e000003 x0 : ffff80000e000000 [ 38.726260] Call trace: [ 38.728703] rproc_handle_resources.constprop.0+0x8c/0x164 [ 38.734196] rproc_boot+0x2fc/0x57c [ 38.737689] rproc_add+0xcc/0x16c [ 38.741004] k3_r5_probe+0x44c/0xe14 [ti_k3_r5_remoteproc] [ 38.746501] platform_probe+0x68/0xc0 [ 38.750168] really_probe+0xbc/0x2dc [ 38.753742] __driver_probe_device+0x78/0x114 [ 38.758099] driver_probe_device+0xd8/0x15c [ 38.762282] __driver_attach+0x94/0x19c [ 38.766119] bus_for_each_dev+0x74/0xd0 [ 38.769954] driver_attach+0x24/0x30 [ 38.773529] bus_add_driver+0x154/0x20c [ 38.777363] driver_register+0x78/0x130 [ 38.781198] __platform_driver_register+0x28/0x34 [ 38.785901] k3_r5_rproc_driver_init+0x20/0x1000 [ti_k3_r5_remoteproc] [ 38.792437] do_one_initcall+0x64/0x1dc [ 38.796272] do_init_module+0x48/0x1d0 [ 38.800023] load_module+0x185c/0x1cc4 [ 38.803770] __do_sys_finit_module+0xa8/0xfc [ 38.808040] __arm64_sys_finit_module+0x20/0x30 [ 38.812571] invoke_syscall+0x48/0x114 [ 38.816320] el0_svc_common.constprop.0+0xcc/0xec [ 38.821053] do_el0_svc+0x2c/0xd0 [ 38.821077] el0_svc+0x2c/0x84 [ 38.821095] el0t_64_sync_handler+0xf4/0x120 [ 38.831698] el0t_64_sync+0x18c/0x190 (this crash was with a stable kernel, but same issue with head of tree) This raises several questions: - Is it a hardware property that RTI1 powers up core 1 as well? - If so, how can we use both watchdog and remoteproc so that the latter loads the firmware for the former? We are currently doing that from U-Boot, but what if that is not desired? Should the watchdog driver take care to not leave core 1 in a different power state behind? - Can and should we do more while parsing the resource table to prevent such crashes? Jan -- Siemens AG, Technology Linux Expert Center
