[PATCH v3 2/4] remoteproc: stm32: Allow hold boot management by the SCMI reset controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The hold boot can be managed by the SCMI controller as a reset.
If the "hold_boot" reset is defined in the device tree, use it.
Else use the syscon controller directly to access to the register.
The support of the SMC call is deprecated but kept for legacy support.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@xxxxxxxxxxx>
---
Updates vs previous version
- Fix error management of the devm_reset_control_get_optional(dev, "hold_boot");

 drivers/remoteproc/stm32_rproc.c | 76 +++++++++++++++++++++++---------
 1 file changed, 55 insertions(+), 21 deletions(-)

diff --git a/drivers/remoteproc/stm32_rproc.c b/drivers/remoteproc/stm32_rproc.c
index 8746cbb1f168..d85c2f8a2d6b 100644
--- a/drivers/remoteproc/stm32_rproc.c
+++ b/drivers/remoteproc/stm32_rproc.c
@@ -79,6 +79,7 @@ struct stm32_mbox {
 
 struct stm32_rproc {
 	struct reset_control *rst;
+	struct reset_control *hold_boot_rst;
 	struct stm32_syscon hold_boot;
 	struct stm32_syscon pdds;
 	struct stm32_syscon m4_state;
@@ -88,7 +89,7 @@ struct stm32_rproc {
 	struct stm32_rproc_mem *rmems;
 	struct stm32_mbox mb[MBOX_NB_MBX];
 	struct workqueue_struct *workqueue;
-	bool secured_soc;
+	bool hold_boot_smc;
 	void __iomem *rsc_va;
 };
 
@@ -413,13 +414,28 @@ static int stm32_rproc_set_hold_boot(struct rproc *rproc, bool hold)
 	struct arm_smccc_res smc_res;
 	int val, err;
 
+	/*
+	 * Three ways to manage the hold boot
+	 * - using SCMI: the hold boot is managed as a reset,
+	 * - using Linux(no SCMI): the hold boot is managed as a syscon register
+	 * - using SMC call (deprecated): use SMC reset interface
+	 */
+
 	val = hold ? HOLD_BOOT : RELEASE_BOOT;
 
-	if (IS_ENABLED(CONFIG_HAVE_ARM_SMCCC) && ddata->secured_soc) {
+	if (ddata->hold_boot_rst) {
+		/* Use the SCMI reset controller */
+		if (!hold)
+			err = reset_control_deassert(ddata->hold_boot_rst);
+		else
+			err =  reset_control_assert(ddata->hold_boot_rst);
+	} else if (IS_ENABLED(CONFIG_HAVE_ARM_SMCCC) && ddata->hold_boot_smc) {
+		/* Use the SMC call */
 		arm_smccc_smc(STM32_SMC_RCC, STM32_SMC_REG_WRITE,
 			      hold_boot.reg, val, 0, 0, 0, 0, &smc_res);
 		err = smc_res.a0;
 	} else {
+		/* Use syscon */
 		err = regmap_update_bits(hold_boot.map, hold_boot.reg,
 					 hold_boot.mask, val);
 	}
@@ -717,34 +733,52 @@ static int stm32_rproc_parse_dt(struct platform_device *pdev,
 		dev_info(dev, "wdg irq registered\n");
 	}
 
-	ddata->rst = devm_reset_control_get_by_index(dev, 0);
+	ddata->rst = devm_reset_control_get_optional(dev, "mcu_rst");
+	if (!ddata->rst) {
+		/* Try legacy fallback method: get it by index */
+		ddata->rst = devm_reset_control_get_by_index(dev, 0);
+	}
 	if (IS_ERR(ddata->rst))
 		return dev_err_probe(dev, PTR_ERR(ddata->rst),
 				     "failed to get mcu_reset\n");
 
 	/*
-	 * if platform is secured the hold boot bit must be written by
-	 * smc call and read normally.
-	 * if not secure the hold boot bit could be read/write normally
+	 * Three ways to manage the hold boot
+	 * - using SCMI: the hold boot is managed as a reset
+	 *    The DT "reset-mames" property should be defined with 2 items:
+	 *        reset-names = "mcu_rst", "hold_boot";
+	 * - using SMC call (deprecated): use SMC reset interface
+	 *    The DT "reset-mames" property is optional, "st,syscfg-tz" is required
+	 * - default(no SCMI, no SMC): the hold boot is managed as a syscon register
+	 *    The DT "reset-mames" property is optional, "st,syscfg-holdboot" is required
 	 */
-	err = stm32_rproc_get_syscon(np, "st,syscfg-tz", &tz);
-	if (err) {
-		dev_err(dev, "failed to get tz syscfg\n");
-		return err;
-	}
 
-	err = regmap_read(tz.map, tz.reg, &tzen);
-	if (err) {
-		dev_err(dev, "failed to read tzen\n");
-		return err;
+	ddata->hold_boot_rst = devm_reset_control_get_optional(dev, "hold_boot");
+	if (IS_ERR(ddata->hold_boot_rst))
+		return dev_err_probe(dev, PTR_ERR(ddata->rst),
+				     "failed to get hold_boot reset\n");
+
+	if (!ddata->hold_boot_rst && IS_ENABLED(CONFIG_HAVE_ARM_SMCCC)) {
+		/* Manage the MCU_BOOT using SMC call */
+		err = stm32_rproc_get_syscon(np, "st,syscfg-tz", &tz);
+		if (!err) {
+			err = regmap_read(tz.map, tz.reg, &tzen);
+			if (err) {
+				dev_err(dev, "failed to read tzen\n");
+				return err;
+			}
+			ddata->hold_boot_smc = tzen & tz.mask;
+		}
 	}
-	ddata->secured_soc = tzen & tz.mask;
 
-	err = stm32_rproc_get_syscon(np, "st,syscfg-holdboot",
-				     &ddata->hold_boot);
-	if (err) {
-		dev_err(dev, "failed to get hold boot\n");
-		return err;
+	if (!ddata->hold_boot_rst && !ddata->hold_boot_smc) {
+		/* Default: hold boot manage it through the syscon controller */
+		err = stm32_rproc_get_syscon(np, "st,syscfg-holdboot",
+					     &ddata->hold_boot);
+		if (err) {
+			dev_err(dev, "failed to get hold boot\n");
+			return err;
+		}
 	}
 
 	err = stm32_rproc_get_syscon(np, "st,syscfg-pdds", &ddata->pdds);
-- 
2.25.1




[Index of Archives]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Photo Sharing]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux