Add a new modem compatible string for QTI SC7280 SoCs and introduce the "qcom,ext-regs" and "qcom,qaccept-regs" bindings needed by the modem sub-system running on SC7280 SoCs. Signed-off-by: Sibi Sankar <sibis@xxxxxxxxxxxxxx> --- .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 32 ++++++++++++++++++++-- 1 file changed, 30 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 494257010629..d802e57701b8 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -15,6 +15,7 @@ on the Qualcomm Hexagon core. "qcom,msm8996-mss-pil" "qcom,msm8998-mss-pil" "qcom,sc7180-mss-pil" + "qcom,sc7280-mss-pil" "qcom,sdm845-mss-pil" - reg: @@ -47,6 +48,7 @@ on the Qualcomm Hexagon core. qcom,msm8996-mss-pil: qcom,msm8998-mss-pil: qcom,sc7180-mss-pil: + qcom,sc7280-mss-pil: qcom,sdm845-mss-pil: must be "wdog", "fatal", "ready", "handover", "stop-ack", "shutdown-ack" @@ -87,6 +89,8 @@ on the Qualcomm Hexagon core. qcom,sc7180-mss-pil: must be "iface", "bus", "xo", "snoc_axi", "mnoc_axi", "nav" + qcom,sc7280-mss-pil: + must be "iface", "xo", "snoc_axi", "offline" qcom,sdm845-mss-pil: must be "iface", "bus", "mem", "xo", "gpll0_mss", "snoc_axi", "mnoc_axi", "prng" @@ -98,7 +102,7 @@ on the Qualcomm Hexagon core. reference to the list of 3 reset-controllers for the wcss sub-system reference to the list of 2 reset-controllers for the modem - sub-system on SC7180, SDM845 SoCs + sub-system on SC7180, SC7280, SDM845 SoCs - reset-names: Usage: required @@ -107,7 +111,7 @@ on the Qualcomm Hexagon core. must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset" for the wcss sub-system must be "mss_restart", "pdc_reset" for the modem - sub-system on SC7180, SDM845 SoCs + sub-system on SC7180, SC7280, SDM845 SoCs For devices where the mba and mpss sub-nodes are not specified, mba/mpss region should be referenced as follows: @@ -173,6 +177,9 @@ For the compatible string below the following supplies are required: qcom,msm8998-mss-pil: must be "cx", "mx" qcom,sc7180-mss-pil: + must be "cx", "mx", "mss" + qcom,sc7280-mss-pil: + must be "cx", "mss" qcom,sdm845-mss-pil: must be "cx", "mx", "mss" @@ -198,6 +205,9 @@ For the compatible string below the following supplies are required: Definition: a phandle reference to a syscon representing TCSR followed by the three offsets within syscon for q6, modem and nc halt registers. + a phandle reference to a syscon representing TCSR followed + by the four offsets within syscon for q6, modem, nc and vq6 + halt registers on SC7280 SoCs. For the compatible strings below the following phandle references are required: "qcom,sc7180-mss-pil" @@ -208,6 +218,24 @@ For the compatible strings below the following phandle references are required: by the offset within syscon for conn_box_spare0 register used by the modem sub-system running on SC7180 SoC. +For the compatible strings below the following phandle references are required: + "qcom,sc7280-mss-pil" +- qcom,ext-regs: + Usage: required + Value type: <prop-encoded-array> + Definition: two phandles reference to syscons representing TCSR_REG and + TCSR register space followed by the two offset within the syscon + to force_clk_en/rscc_disable and axim1_clk_off/crypto_clk_off + registers respectively. + +- qcom,qaccept-regs: + Usage: required + Value type: <prop-encoded-array> + Definition: a phandle reference to a syscon representing TCSR followed + by the three offsets within syscon for mdm, cx and axi + qaccept registers used by the modem sub-system running on + SC7280 SoC. + The Hexagon node must contain iommus property as described in ../iommu/iommu.txt on platforms which do not have TrustZone. -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
