Hi Mathieu, On 4/6/20 2:59 PM, Mathieu Poirier wrote: > On Tue, Mar 24, 2020 at 03:18:15PM -0500, Suman Anna wrote: >> The Texas Instruments K3 family of SoCs have one or more dual-core >> Arm Cortex R5F processor subsystems/clusters (R5FSS). The clusters >> can be split between multiple voltage domains as well. Add the device >> tree bindings document for these R5F subsystem devices. These R5F >> processors do not have an MMU, and so require fixed memory carveout >> regions matching the firmware image addresses. The nodes require more >> than one memory region, with the first memory region used for DMA >> allocations at runtime. The remaining memory regions are reserved >> and are used for the loading and running of the R5F remote processors. >> The R5F processors can also optionally use any internal on-chip SRAM >> memories either for executing code or using it as fast-access data. >> >> The added example illustrates the DT nodes for the single R5FSS device >> present on K3 AM65x family of SoCs. >> >> Signed-off-by: Suman Anna <s-anna@xxxxxx> >> --- >> Hi Rob, >> >> The dt_bindings_check seems to throw couple of warnings around the >> usage of ranges because the tooling is adding the #address-cells >> and #size-cells of 1 by default, whereas our actual code uses 2. >> No issues are found with dtbs_check. >> >> regards >> Suman >> >> .../bindings/remoteproc/ti,k3-r5f-rproc.yaml | 338 ++++++++++++++++++ >> 1 file changed, 338 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml >> >> diff --git a/Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml b/Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml >> new file mode 100644 >> index 000000000000..bbfc1e6ae884 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/remoteproc/ti,k3-r5f-rproc.yaml >> @@ -0,0 +1,338 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/remoteproc/ti,k3-r5f-rproc.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: TI K3 R5F processor subsystems >> + >> +maintainers: >> + - Suman Anna <s-anna@xxxxxx> >> + >> +description: | >> + The TI K3 family of SoCs usually have one or more dual-core Arm Cortex R5F >> + processor subsystems/clusters (R5FSS). The dual core cluster can be used >> + either in a LockStep mode providing safety/fault tolerance features or in a >> + Split mode providing two individual compute cores for doubling the compute >> + capacity. These are used together with other processors present on the SoC >> + to achieve various system level goals. >> + >> + Each Dual-Core R5F sub-system is represented as a single DTS node >> + representing the cluster, with a pair of child DT nodes representing >> + the individual R5F cores. Each node has a number of required or optional >> + properties that enable the OS running on the host processor to perform >> + the device management of the remote processor and to communicate with the >> + remote processor. >> + >> +# Required properties: >> +# -------------------- >> +# The following are the mandatory properties: >> + >> +properties: >> + $nodename: >> + pattern: "^r5fss(@.*)?" >> + >> + compatible: >> + enum: >> + - ti,am654-r5fss >> + - ti,j721e-r5fss >> + >> + power-domains: >> + description: | >> + Should contain a phandle to a PM domain provider node and an args >> + specifier containing the R5FSS device id value. This property is >> + as per the binding, >> + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt >> + maxItems: 1 >> + >> + "#address-cells": >> + const: 1 >> + >> + "#size-cells": >> + const: 1 >> + >> + ranges: >> + description: | >> + Standard ranges definition providing address translations for >> + local R5F TCM address spaces to bus addresses. >> + >> +# Optional properties: >> +# -------------------- >> + >> + lockstep-mode: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + enum: [0, 1] >> + description: | >> + Configuration Mode for the Dual R5F cores within the R5F >> + cluster. Should be either a value of 1 (LockStep mode) or >> + 0 (Split mode), default is LockStep mode if omitted. > > Should I deduce lockstep means SMP and split mode two processors running in UP > mode? No, slightly different from SMP. It is a safety/fault-tolerance mode, the 2 cores run the same code, and then the output is compared, and an error is thrown if they yield different results. > >> + >> +# R5F Processor Child Nodes: >> +# ========================== >> + >> +patternProperties: >> + "^r5f@[a-f0-9]+$": >> + type: object >> + description: | >> + The R5F Sub-System device node should define two R5F child nodes, each >> + node representing a TI instantiation of the Arm Cortex R5F core. There >> + are some specific integration differences for the IP like the usage of >> + a Region Address Translator (RAT) for translating the larger SoC bus >> + addresses into a 32-bit address space for the processor. >> + >> +# Required properties: >> +# -------------------- >> +# The following are the mandatory properties: >> + >> + properties: >> + compatible: >> + enum: >> + - ti,am654-r5f >> + - ti,j721e-r5f >> + >> + reg: >> + description: | >> + Should contain an entry for each value in 'reg-names'. >> + Each entry should have the memory region's start address >> + and the size of the region, the representation matching >> + the parent node's '#address-cells' and '#size-cells' values. >> + maxItems: 2 >> + >> + reg-names: >> + description: | >> + Should contain strings with the names of the specific internal >> + internal memory regions, and should be defined in this order > > There is two "internal" in a row. Thanks, will fix it up. > >> + maxItems: 2 >> + items: >> + - const: atcm >> + - const: btcm >> + >> + ti,sci: >> + $ref: /schemas/types.yaml#/definitions/phandle >> + description: >> + Should be a phandle to the TI-SCI System Controller node >> + >> + ti,sci-dev-id: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + description: | >> + Should contain the TI-SCI device id corresponding to the R5F core. >> + Please refer to the corresponding System Controller documentation >> + for valid values for the R5F cores. >> + >> + ti,sci-proc-ids: >> + description: Should contain a single tuple of <proc_id host_id>. >> + allOf: >> + - $ref: /schemas/types.yaml#/definitions/uint32-matrix >> + - maxItems: 1 >> + items: >> + items: >> + - description: TI-SCI processor id for the R5F core device >> + - description: TI-SCI host id to which processor control >> + ownership should be transferred to >> + >> + resets: >> + description: | >> + Should contain the phandle to the reset controller node >> + managing the resets for this device, and a reset >> + specifier. Please refer to the following reset bindings >> + for the reset argument specifier, >> + Documentation/devicetree/bindings/reset/ti,sci-reset.txt >> + for AM65x and J721E SoCs >> + >> + firmware-name: >> + description: | >> + Should contain the name of the default firmware image >> + file located on the firmware search path >> + >> +# The following properties are mandatory for R5F Core0 in both LockStep and Split >> +# modes, and are mandatory for R5F Core1 _only_ in Split mode. They are unused for >> +# R5F Core1 in LockStep mode: >> + >> + mboxes: >> + description: | >> + OMAP Mailbox specifier denoting the sub-mailbox, to be used for >> + communication with the remote processor. This property should match >> + with the sub-mailbox node used in the firmware image. The specifier >> + format is as per the bindings, >> + Documentation/devicetree/bindings/mailbox/omap-mailbox.txt > > In the example below node "mcu_r5f1" has a "mboxes" property despite being in lockstep mode. I > haven't delved in the code yet, perharps I'll find an answer in there. Yeah, it is defined, but won't be parsed or used if the cluster is in lockstep mode as my comment above says. The lockstep capability is an efuse bit, so on some SoC variants, which do not have the capability, the cluster is hard-wired for Split-mode only. And we detect that in the driver irrespective of the lockstep-mode value. > >> + >> + memory-region: >> + minItems: 2 >> + description: | >> + phandle to the reserved memory nodes to be associated with the remoteproc >> + device. There should be atleast two reserved memory nodes defined - the > > s/atleast/at least OK > >> + first one would be used for dynamic DMA allocations like vrings and vring >> + buffers, and the remaining ones used for the firmware image sections. The >> + reserved memory nodes should be carveout nodes, and should be defined as >> + per the bindings in >> + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt >> + >> +# Optional properties: >> +# -------------------- >> +# The following properties are optional properties for each of the R5F cores: >> + >> + atcm-enable: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + enum: [0, 1] >> + description: | >> + R5F core configuration mode dictating if ATCM should be enabled. R5F >> + view of ATCM dictated by loczrama property. Should be either a value >> + of 1 (enabled) or 0 (disabled), default is disabled if omitted. > > What is ATCM and why would one want to enable the feature? TCM stands for Tightly Coupled Memory (an internal RAM memory essentially), and R5 supports two such bank interfaces called A and B. Some of the specs use TCMA or TCMB as well. > >> + >> + btcm-enable: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + enum: [0, 1] >> + description: | >> + R5F core configuration mode dictating if BTCM should be enabled. R5F >> + view of BTCM dictated by loczrama property. Should be either a value >> + of 1 (enabled) or 0 (disabled), default is enabled if omitted. > > Same here, there is no way to tell what BTCM is. > >> + >> + loczrama: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + enum: [0, 1] >> + description: | >> + R5F core configuration mode dictating which TCM should appear at >> + address 0 (from core's view). Should be either a value of 1 (ATCM >> + at 0x0) or 0 (BTCM at 0x0), default value is 1 if omitted. > > loczrama: Location Zero Ram Address? Guess so. I never found the expansion. Can both core show up at the address 0x0? > In the example below both cores have the same setting for atcm, btcm and > loczrama. Each core has their own ATCM, BTCM and loczrama settings and are effective in Split-mode. Only Core0 memories and settings are used in LockStep mode. > >> + >> + sram: >> + $ref: /schemas/types.yaml#/definitions/phandle-array >> + minItems: 1 >> + description: | >> + pHandles to one or more reserved on-chip SRAM region. The regions >> + should be defined as child nodes of the respective SRAM node, and >> + should be defined as per the generic bindings in, >> + Documentation/devicetree/bindings/sram/sram.yaml > > Is the behaviour the same whether operating in locksetup mode and split mode? This is per core. So, just like mboxes, will be unused on Core1 if the cluster is configured for LockStep mode. regards Suman > > Thanks, > Mathieu > >> + >> + required: >> + - compatible >> + - reg >> + - reg-names >> + - ti,sci >> + - ti,sci-dev-id >> + - ti,sci-proc-ids >> + - resets >> + - firmware-name >> + >> + additionalProperties: false >> + >> +required: >> + - compatible >> + - power-domains >> + - "#address-cells" >> + - "#size-cells" >> + - ranges >> + >> +additionalProperties: false >> + >> +examples: >> + - | >> + >> + //Example: AM654 SoC >> + /* R5F DDR Carveout reserved memory nodes */ >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@9b000000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0x9b000000 0x00 0x100000>; >> + no-map; >> + }; >> + >> + mcu_r5fss0_core1_memory_region: r5f-memory@9b100000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0x9b100000 0x00 0xf00000>; >> + no-map; >> + }; >> + >> + mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c000000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0x9c000000 0x00 0x100000>; >> + no-map; >> + }; >> + >> + mcu_r5fss0_core0_memory_region: r5f-memory@9c100000 { >> + compatible = "shared-dma-pool"; >> + reg = <0x00 0x9c100000 0x00 0x700000>; >> + no-map; >> + }; >> + }; >> + >> + cbass_main: interconnect@100000 { >> + compatible = "simple-bus"; >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges = <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>, >> + <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>, >> + <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00080000>; >> + >> + cbass_mcu: interconnect@28380000 { >> + compatible = "simple-bus"; >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges = <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>, /* MCU R5F Core0 */ >> + <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>, /* MCU R5F Core1 */ >> + <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00080000>; /* MCU SRAM */ >> + >> + /* MCU domain SRAM node */ >> + mcu_ram: mcu-ram@41c00000 { >> + compatible = "mmio-sram"; >> + reg = <0x00 0x41c00000 0x00 0x80000>; >> + ranges = <0x0 0x00 0x41c00000 0x80000>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + mcu_r5fss0_core0_sram: r5f-sram@0 { >> + reg = <0x0 0x40000>; >> + }; >> + }; >> + >> + /* AM65x MCU R5FSS node */ >> + mcu_r5fss0: r5fss@41000000 { >> + compatible = "ti,am654-r5fss"; >> + power-domains = <&k3_pds 129>; >> + lockstep-mode = <1>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0x41000000 0x00 0x41000000 0x20000>, >> + <0x41400000 0x00 0x41400000 0x20000>; >> + >> + mcu_r5f0: r5f@41000000 { >> + compatible = "ti,am654-r5f"; >> + reg = <0x41000000 0x00008000>, >> + <0x41010000 0x00008000>; >> + reg-names = "atcm", "btcm"; >> + ti,sci = <&dmsc>; >> + ti,sci-dev-id = <159>; >> + ti,sci-proc-ids = <0x01 0xFF>; >> + resets = <&k3_reset 159 1>; >> + firmware-name = "am65x-mcu-r5f0_0-fw"; >> + atcm-enable = <1>; >> + btcm-enable = <1>; >> + loczrama = <1>; >> + mboxes = <&mailbox0 &mbox_mcu_r5fss0_core0>; >> + memory-region = <&mcu_r5fss0_core0_dma_memory_region>, >> + <&mcu_r5fss0_core0_memory_region>; >> + sram = <&mcu_r5fss0_core0_sram>; >> + }; >> + >> + mcu_r5f1: r5f@41400000 { >> + compatible = "ti,am654-r5f"; >> + reg = <0x41400000 0x00008000>, >> + <0x41410000 0x00008000>; >> + reg-names = "atcm", "btcm"; >> + ti,sci = <&dmsc>; >> + ti,sci-dev-id = <245>; >> + ti,sci-proc-ids = <0x02 0xFF>; >> + resets = <&k3_reset 245 1>; >> + firmware-name = "am65x-mcu-r5f0_1-fw"; >> + atcm-enable = <1>; >> + btcm-enable = <1>; >> + loczrama = <1>; >> + mboxes = <&mailbox1 &mbox_mcu_r5fss0_core1>; >> + }; >> + }; >> + }; >> + }; >> -- >> 2.23.0 >>
