Re: [PATCH v2 6/6] remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri 12 Oct 02:40 PDT 2018, Govind Singh wrote:
> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
> index 601dd9f..cc83832 100644
> --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
> @@ -13,6 +13,7 @@ on the Qualcomm Hexagon core.
>  		    "qcom,msm8974-mss-pil"
>  		    "qcom,msm8996-mss-pil"
>  		    "qcom,sdm845-mss-pil"
> +		    "qcom,qcs404-wcss-non-pas"

Let's use the form qcom,qcs404-wcnss-pas for the PAS case and
qcom,qcs404-wcnss-pil for the non-PAS.

>  
>  - reg:
>  	Usage: required
> diff --git a/drivers/remoteproc/qcom_q6v5_wcss.c b/drivers/remoteproc/qcom_q6v5_wcss.c
[..]
>  /* Q6SS Register Offsets */
> -#define Q6SS_RESET_REG		0x014
> +#define Q6SS_RESET_REG			0x014

Most of these changes to defines are just reformatting, making it hard
to track what actually changed. Please do send a separate patch fixing
the indentation instead.

>  #define Q6SS_GFMUX_CTL_REG		0x020
>  #define Q6SS_PWR_CTL_REG		0x030
>  #define Q6SS_MEM_PWR_CTL		0x0B0
> +#define Q6SS_STRAP_ACC			0x110
> +#define Q6SS_CGC_OVERRIDE		0x034
> +#define Q6SS_BCR_REG			0x6000
>  
>  /* AXI Halt Register Offsets */
>  #define AXI_HALTREQ_REG			0x0
> @@ -36,6 +44,9 @@
>  #define Q6SS_CORE_ARES			BIT(1)
>  #define Q6SS_BUS_ARES_ENABLE		BIT(2)
>  
> +/* Q6SS_BRC_RESET */
> +#define Q6SS_BRC_BLK_ARES		BIT(0)
> +
>  /* Q6SS_GFMUX_CTL */
>  #define Q6SS_CLK_ENABLE			BIT(1)
>  
> @@ -44,14 +55,15 @@
>  #define Q6SS_SLP_RET_N			BIT(19)
>  #define Q6SS_CLAMP_IO			BIT(20)
>  #define QDSS_BHS_ON			BIT(21)
> +#define QDSS_Q6_MEMORIES		GENMASK(15, 0)
>  
>  /* Q6SS parameters */
> -#define Q6SS_LDO_BYP		BIT(25)
> -#define Q6SS_BHS_ON		BIT(24)
> -#define Q6SS_CLAMP_WL		BIT(21)
> +#define Q6SS_LDO_BYP			BIT(25)
> +#define Q6SS_BHS_ON			BIT(24)
> +#define Q6SS_CLAMP_WL			BIT(21)
>  #define Q6SS_CLAMP_QMC_MEM		BIT(22)
>  #define HALT_CHECK_MAX_LOOPS		200
> -#define Q6SS_XO_CBCR		GENMASK(5, 3)
> +#define Q6SS_XO_CBCR			GENMASK(5, 3)
>  
>  /* Q6SS config/status registers */
>  #define TCSR_GLOBAL_CFG0	0x0
> @@ -70,12 +82,23 @@
>  #define TCSR_WCSS_CLK_MASK	0x1F
>  #define TCSR_WCSS_CLK_ENABLE	0x14
>  
> +enum {
> +	WCSS_IPQ8074,
> +	WCSS_QCS404,
> +};
> +
>  struct wcss_data {
> -	void (*pas_handover)(struct qcom_q6v5 *q6v5);
>  	const char *firmware_name;
>  	int crash_reason_smem;
>  	int version;
>  	int pas_id;
> +	bool has_aggre2_clk;

Please don't introduce properties and code that you don't use.

> +	bool aon_reset_required;
> +	const char *ssr_name;
> +	const char *sysmon_name;
> +	int ssctl_id;
> +	const struct rproc_ops *ops;
> +	void (*pas_handover)(struct qcom_q6v5 *q6v5);
>  };
>  
>  struct q6v5_wcss {
> @@ -83,12 +106,37 @@ struct q6v5_wcss {
>  
>  	void __iomem *reg_base;
>  	void __iomem *rmb_base;
> +	void __iomem *q6stop_base;
>  
>  	struct regmap *halt_map;
>  	u32 halt_q6;
>  	u32 halt_wcss;
>  	u32 halt_nc;
>  
> +	struct clk *xo;
> +	struct clk *aggre2_clk;

You don't use aggre2_clk, so you can drop this.

> +	struct clk *ahbfabric_cbcr_clk;
> +	struct clk *gcc_abhs_cbcr;
> +	struct clk *gcc_axim_cbcr;
> +	struct clk *lcc_csr_cbcr;
> +	struct clk *ahbs_cbcr;
> +	struct clk *tcm_slave_cbcr;
> +	struct clk *qdsp6ss_abhm_cbcr;
> +	struct clk *qdsp6ss_sleep_cbcr;
> +	struct clk *qdsp6ss_axim_cbcr;
> +	struct clk *qdsp6ss_xo_cbcr;
> +	struct clk *qdsp6ss_core_gfmux;
> +	struct clk *wcss_bcr_cbcr;

It looks like you're able to group most of these up in one or more
clk_bulk_data

> +	struct regulator *cx_supply;
> +	struct regulator *px_supply;

px_supply isn't documented in the DT binding, do you actually use it?

> +
> +	bool has_aggre2_clk;
> +	bool aon_reset_required;
> +
> +	struct qcom_rproc_glink glink_subdev;
> +	struct qcom_rproc_ssr ssr_subdev;
> +	struct qcom_sysmon *sysmon;
> +
>  	struct reset_control *wcss_aon_reset;
>  	struct reset_control *wcss_reset;
>  	struct reset_control *wcss_q6_reset;
> @@ -99,7 +147,6 @@ struct q6v5_wcss {
>  	phys_addr_t mem_reloc;
>  	void *mem_region;
>  	size_t mem_size;
> -
>  	int crash_reason_smem;
>  	int pas_id;
>  	int version;
> @@ -245,6 +292,214 @@ static int q6v5_wcss_start(struct rproc *rproc)
>  	return ret;
>  }
[..]
> +static int q6v5_wcss_qcs404_reset(struct q6v5_wcss *wcss)
> +{
> +	unsigned long val;
> +
> +	writel(0x80800000, wcss->reg_base + Q6SS_STRAP_ACC);
> +
> +	/* Start core execution */
> +	val = readl(wcss->reg_base + Q6SS_RESET_REG);
> +	val &= ~Q6SS_STOP_CORE;
> +	writel(val, wcss->reg_base + Q6SS_RESET_REG);
> +
> +	return 0;
> +}
> +
> +static int q6v5_qcs404_wcss_start(struct rproc *rproc)

There are commonalities between this and the existing start function,
can we align them instead of duplicating?

> +{
> +	struct q6v5_wcss *wcss = rproc->priv;
> +	int ret;
> +
> +	ret = clk_prepare_enable(wcss->xo);
> +	if (ret)
> +		return ret;
> +
> +	if (wcss->has_aggre2_clk) {
> +		ret = clk_prepare_enable(wcss->aggre2_clk);
> +		if (ret)
> +			goto disable_xo_clk;
> +	}
> +
> +	ret = regulator_enable(wcss->cx_supply);
> +	if (ret)
> +		goto disable_aggre2_clk;
> +
> +	ret = regulator_enable(wcss->px_supply);
> +	if (ret)
> +		goto disable_cx_supply;
> +
> +	qcom_q6v5_prepare(&wcss->q6v5);
> +
> +	ret = q6v5_wcss_qcs404_power_on(wcss);
> +	if (ret) {
> +		dev_err(wcss->dev, "wcss clk_enable failed\n");
> +		goto disable_px_supply;
> +	}
> +
> +	writel(rproc->bootaddr >> 4, wcss->reg_base + Q6SS_RST_EVB);
> +
> +	ret = q6v5_wcss_qcs404_reset(wcss);

Just inline the 5 lines here.

> +	if (ret)
> +		dev_err(wcss->dev, "De-assert QDSP6 out of reset failed\n");

The function can't fail...

> +
> +	ret = qcom_q6v5_wait_for_start(&wcss->q6v5, 5 * HZ);
> +	if (ret == -ETIMEDOUT) {
> +		dev_err(wcss->dev, "start timed out\n");
> +		goto disable_px_supply;
> +	}
> +
> +	return 0;
> +
> +disable_px_supply:
> +	regulator_disable(wcss->px_supply);
> +disable_cx_supply:
> +	regulator_disable(wcss->cx_supply);
> +disable_aggre2_clk:
> +	if (wcss->has_aggre2_clk)
> +		clk_disable_unprepare(wcss->aggre2_clk);
> +disable_xo_clk:
> +	clk_disable_unprepare(wcss->xo);
> +
> +	return ret;
> +}
> +
>  static void q6v5_wcss_halt_axi_port(struct q6v5_wcss *wcss,
>  				    struct regmap *halt_map,
>  				    u32 offset)
> @@ -279,6 +534,77 @@ static void q6v5_wcss_halt_axi_port(struct q6v5_wcss *wcss,
>  	regmap_write(halt_map, offset + AXI_HALTREQ_REG, 0);
>  }
>  
> +static int q6v5_qcs404_wcss_shutdown(struct q6v5_wcss *wcss)
> +{
> +	unsigned long val;
> +	int ret;
> +
> +	q6v5_wcss_halt_axi_port(wcss, wcss->halt_map, wcss->halt_wcss);
> +
> +	/* assert clamps to avoid MX current inrush */
> +	val = readl(wcss->reg_base + Q6SS_PWR_CTL_REG);
> +	val |= (Q6SS_CLAMP_IO | Q6SS_CLAMP_WL | Q6SS_CLAMP_QMC_MEM);
> +	writel(val, wcss->reg_base + Q6SS_PWR_CTL_REG);
> +
> +	/* Disable memories by turning off memory foot/headswitch */
> +	writel((readl(wcss->reg_base + Q6SS_MEM_PWR_CTL) &
> +		~QDSS_Q6_MEMORIES),
> +		wcss->reg_base + Q6SS_MEM_PWR_CTL);
> +
> +	/* Clear the BHS_ON bit */
> +	val = readl(wcss->reg_base + Q6SS_PWR_CTL_REG);
> +	val &= ~Q6SS_BHS_ON;
> +	writel(val, wcss->reg_base + Q6SS_PWR_CTL_REG);
> +
> +	clk_disable_unprepare(wcss->ahbfabric_cbcr_clk);
> +	clk_disable_unprepare(wcss->lcc_csr_cbcr);
> +	clk_disable_unprepare(wcss->tcm_slave_cbcr);
> +	clk_disable_unprepare(wcss->qdsp6ss_abhm_cbcr);
> +	clk_disable_unprepare(wcss->qdsp6ss_axim_cbcr);
> +	clk_disable_unprepare(wcss->qdsp6ss_xo_cbcr);
> +	clk_disable_unprepare(wcss->ahbs_cbcr);
> +	clk_disable_unprepare(wcss->wcss_bcr_cbcr);
> +	clk_disable_unprepare(wcss->qdsp6ss_core_gfmux);
> +	clk_disable_unprepare(wcss->gcc_abhs_cbcr);
> +
> +	ret = reset_control_assert(wcss->wcss_reset);
> +	if (ret) {
> +		dev_err(wcss->dev, "wcss_reset failed\n");
> +		return ret;
> +	}
> +	usleep_range(200, 300);
> +
> +	ret = reset_control_deassert(wcss->wcss_reset);
> +	if (ret) {
> +		dev_err(wcss->dev, "wcss_reset failed\n");
> +		return ret;
> +	}

Can't we deassert this in start(), as that would make it better follow
the IPQ implementation.

> +	usleep_range(200, 300);
> +
> +	clk_disable_unprepare(wcss->gcc_axim_cbcr);
> +
> +	return 0;
> +}
> +
> +static int q6v5_qcs404_wcss_stop(struct rproc *rproc)
> +{
> +	struct q6v5_wcss *wcss = rproc->priv;
> +	int ret;
> +
> +	/* WCSS powerdown */
> +	ret = qcom_q6v5_request_stop(&wcss->q6v5);
> +	if (ret == -ETIMEDOUT)
> +		dev_err(wcss->dev, "timed out on wait\n");
> +
> +	ret = q6v5_qcs404_wcss_shutdown(wcss);

This call is the only part that differs from the existing stop(), so
please switch here instead of duplicating the function.

> +	if (ret)
> +		return ret;
> +
> +	qcom_q6v5_unprepare(&wcss->q6v5);
> +
> +	return 0;
> +}
> +
>  static int q6v5_wcss_powerdown(struct q6v5_wcss *wcss)
>  {
>  	int ret;
> @@ -312,7 +638,8 @@ static int q6v5_wcss_powerdown(struct q6v5_wcss *wcss)
>  	}
>  
>  	/* 6 - De-assert WCSS_AON reset */
> -	reset_control_assert(wcss->wcss_aon_reset);
> +	if (wcss->aon_reset_required)

aon_reset_required is set for IPQ, which is the only case which will
call this function, so no need to check for this.

> +		reset_control_assert(wcss->wcss_aon_reset);
>  
>  	/* 7 - Disable WCSSAON_CONFIG 13 */
>  	val = readl(wcss->rmb_base + SSCAON_CONFIG);
> @@ -392,6 +719,17 @@ static int q6v5_q6_powerdown(struct q6v5_wcss *wcss)
>  	return 0;
>  }
>  
> +static void q6v5_wcss_pas_handover(struct qcom_q6v5 *q6v5)

Why does the non-PAS driver have a method named pas_handover()?

> +{
> +	struct q6v5_wcss *wcss = container_of(q6v5, struct q6v5_wcss, q6v5);
> +
> +	regulator_disable(wcss->px_supply);
> +	regulator_disable(wcss->cx_supply);
> +	if (wcss->has_aggre2_clk)
> +		clk_disable_unprepare(wcss->aggre2_clk);
> +	clk_disable_unprepare(wcss->xo);
> +}
> +
>  static int q6v5_wcss_stop(struct rproc *rproc)
>  {
>  	struct q6v5_wcss *wcss = rproc->priv;
> @@ -439,7 +777,7 @@ static int q6v5_wcss_load(struct rproc *rproc, const struct firmware *fw)
>  				     wcss->mem_size, &wcss->mem_reloc);
>  }
>  
> -static const struct rproc_ops q6v5_wcss_ops = {
> +static const struct rproc_ops q6v5_wcss_ipq8074_ops = {

Rename this when you introduce it in the previous patch.

>  	.start = q6v5_wcss_start,
>  	.stop = q6v5_wcss_stop,
>  	.da_to_va = q6v5_wcss_da_to_va,
> @@ -447,23 +785,33 @@ static int q6v5_wcss_load(struct rproc *rproc, const struct firmware *fw)
>  	.get_boot_addr = rproc_elf_get_boot_addr,
>  };
>  
> +static const struct rproc_ops q6v5_wcss_qcs404_ops = {
> +	.start = q6v5_qcs404_wcss_start,
> +	.stop = q6v5_qcs404_wcss_stop,
> +	.da_to_va = q6v5_wcss_da_to_va,
> +	.load = q6v5_wcss_load,
> +	.get_boot_addr = rproc_elf_get_boot_addr,
> +};
> +
>  static int q6v5_wcss_init_reset(struct q6v5_wcss *wcss)
>  {
>  	struct device *dev = wcss->dev;
>  
> -	wcss->wcss_aon_reset = devm_reset_control_get(dev, "wcss_aon_reset");
> -	if (IS_ERR(wcss->wcss_aon_reset)) {
> -		dev_err(wcss->dev, "unable to acquire wcss_aon_reset\n");
> -		return PTR_ERR(wcss->wcss_aon_reset);
> +	if (wcss->aon_reset_required) {

Pass desc, or an argument to the function, rather than stashing this
value in wcss. And just leave wcss_aon_reset NULL when not used.

> +		wcss->wcss_aon_reset = devm_reset_control_get_exclusive(dev, "wcss_aon_reset");
> +		if (IS_ERR(wcss->wcss_aon_reset)) {
> +			dev_err(wcss->dev, "fail to acquire wcss_aon_reset\n");
> +			return PTR_ERR(wcss->wcss_aon_reset);
> +		}
>  	}
>  
> -	wcss->wcss_reset = devm_reset_control_get(dev, "wcss_reset");
> +	wcss->wcss_reset = devm_reset_control_get_exclusive(dev, "wcss_reset");

Please submit this in a separate patch.

>  	if (IS_ERR(wcss->wcss_reset)) {
>  		dev_err(wcss->dev, "unable to acquire wcss_reset\n");
>  		return PTR_ERR(wcss->wcss_reset);
>  	}
>  
> -	wcss->wcss_q6_reset = devm_reset_control_get(dev, "wcss_q6_reset");
> +	wcss->wcss_q6_reset = devm_reset_control_get_exclusive(dev, "wcss_q6_reset");

Ditto

>  	if (IS_ERR(wcss->wcss_q6_reset)) {
>  		dev_err(wcss->dev, "unable to acquire wcss_q6_reset\n");
>  		return PTR_ERR(wcss->wcss_q6_reset);
> @@ -475,36 +823,73 @@ static int q6v5_wcss_init_reset(struct q6v5_wcss *wcss)
>  static int q6v5_wcss_init_mmio(struct q6v5_wcss *wcss,
>  			       struct platform_device *pdev)
>  {
> +	struct device_node *syscon;
>  	struct of_phandle_args args;
>  	struct resource *res;
>  	int ret;
>  
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qdsp6");
> -	wcss->reg_base = devm_ioremap_resource(&pdev->dev, res);
> +	wcss->reg_base = devm_ioremap(&pdev->dev, res->start,
> +				      resource_size(res));

Isn't this the same thing?

>  	if (IS_ERR(wcss->reg_base))
>  		return PTR_ERR(wcss->reg_base);
>  
> -	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rmb");
> -	wcss->rmb_base = devm_ioremap_resource(&pdev->dev, res);
> -	if (IS_ERR(wcss->rmb_base))
> -		return PTR_ERR(wcss->rmb_base);
> -
> -	ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node,
> -					       "qcom,halt-regs", 3, 0, &args);
> -	if (ret < 0) {
> -		dev_err(&pdev->dev, "failed to parse qcom,halt-regs\n");
> -		return -EINVAL;
> +	if (wcss->version == WCSS_QCS404) {
> +		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> +						   "q6stop");
> +		if (!res) {
> +			dev_err(&pdev->dev, "invalid q6stop_base resource\n");
> +			return -EINVAL;
> +		}
> +
> +		wcss->q6stop_base = devm_ioremap(&pdev->dev, res->start,
> +						 resource_size(res));
> +		if (IS_ERR(wcss->q6stop_base))
> +			return PTR_ERR(wcss->q6stop_base);
> +
> +		syscon = of_parse_phandle(pdev->dev.of_node,
> +					  "qcom,halt-regs", 0);
> +		if (!syscon) {
> +			dev_err(&pdev->dev, "failed to parse qcom,halt-regs\n");
> +			return -EINVAL;
> +		}
> +
> +		wcss->halt_map = syscon_node_to_regmap(syscon);
> +		of_node_put(syscon);
> +		if (IS_ERR(wcss->halt_map))
> +			return PTR_ERR(wcss->halt_map);
> +
> +		ret = of_property_read_u32_index(pdev->dev.of_node,
> +						 "qcom,halt-regs",
> +						 1, &wcss->halt_wcss);

Okay, so the QCS404 doesn't need to halt q6 or nc?

I think you should change the fixed_args to
of_property_read_variable_u32_array() and try not to duplicate this.

> +		if (ret < 0) {
> +			dev_err(&pdev->dev, "no offset in syscon\n");
> +			return ret;
> +		}
> +	} else {
> +		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rmb");
> +		wcss->rmb_base = devm_ioremap_resource(&pdev->dev, res);
> +		if (IS_ERR(wcss->rmb_base))
> +			return PTR_ERR(wcss->rmb_base);
> +
> +		ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node,
> +						       "qcom,halt-regs", 3,
> +							0, &args);
> +		if (ret < 0) {
> +			dev_err(&pdev->dev, "failed to parse qcom,halt-regs\n");
> +			return -EINVAL;
> +		}
> +
> +		wcss->halt_map = syscon_node_to_regmap(args.np);
> +		of_node_put(args.np);
> +		if (IS_ERR(wcss->halt_map))
> +			return PTR_ERR(wcss->halt_map);
> +
> +		wcss->halt_q6 = args.args[0];
> +		wcss->halt_wcss = args.args[1];
> +		wcss->halt_nc = args.args[2];
>  	}
>  
> -	wcss->halt_map = syscon_node_to_regmap(args.np);
> -	of_node_put(args.np);
> -	if (IS_ERR(wcss->halt_map))
> -		return PTR_ERR(wcss->halt_map);
> -
> -	wcss->halt_q6 = args.args[0];
> -	wcss->halt_wcss = args.args[1];
> -	wcss->halt_nc = args.args[2];
> -
>  	return 0;
>  }
>  
> @@ -537,6 +922,144 @@ static int q6v5_alloc_memory_region(struct q6v5_wcss *wcss)
>  	return 0;
>  }
>  
> +static int q6v5_wcss_init_clock(struct q6v5_wcss *wcss)
> +{
> +	int ret;
> +
> +	wcss->xo = devm_clk_get(wcss->dev, "xo");
> +	if (IS_ERR(wcss->xo)) {
> +		ret = PTR_ERR(wcss->xo);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(wcss->dev, "failed to get xo clock");
> +		return ret;
> +	}
> +
> +	if (wcss->has_aggre2_clk) {
> +		wcss->aggre2_clk = devm_clk_get(wcss->dev, "aggre2");
> +		if (IS_ERR(wcss->aggre2_clk)) {
> +			ret = PTR_ERR(wcss->aggre2_clk);
> +			if (ret != -EPROBE_DEFER)
> +				dev_err(wcss->dev,
> +					"failed to get aggre2 clock");
> +			return ret;
> +		}
> +	}
> +
> +	wcss->gcc_abhs_cbcr = devm_clk_get(wcss->dev, "gcc_abhs_cbcr");

Please also update the binding to describe these clocks for this
compatible.

[..]
> @@ -559,7 +1082,11 @@ static int q6v5_wcss_probe(struct platform_device *pdev)
>  	wcss->dev = &pdev->dev;
>  	wcss->pas_id = desc->pas_id;
>  	wcss->version = desc->version;
> -	wcss->crash_reason_smem = desc->crash_reason_smem;
> +	wcss->has_aggre2_clk = desc->has_aggre2_clk;
> +	wcss->aon_reset_required = desc->aon_reset_required;
> +	platform_set_drvdata(pdev, wcss);

I don't see a platform_get_drvdata(), so do you really need this?

> +
> +	wcss->version = desc->version;
>  
>  	ret = q6v5_wcss_init_mmio(wcss, pdev);
>  	if (ret)
> @@ -569,6 +1096,16 @@ static int q6v5_wcss_probe(struct platform_device *pdev)
>  	if (ret)
>  		goto free_rproc;
>  
> +	if (wcss->version == WCSS_QCS404) {
> +		ret = q6v5_wcss_init_clock(wcss);
> +		if (ret)
> +			goto free_rproc;
> +
> +		ret = q6v5_wcss_init_regulator(wcss);
> +		if (ret)
> +			goto free_rproc;

Does the IPQ really not have any clocks or regulators?

> +	}
> +
>  	ret = q6v5_wcss_init_reset(wcss);
>  	if (ret)
>  		goto free_rproc;
> @@ -578,6 +1115,14 @@ static int q6v5_wcss_probe(struct platform_device *pdev)
>  	if (ret)
>  		goto free_rproc;
>  
> +	if (wcss->version == WCSS_QCS404) {
> +		qcom_add_glink_subdev(rproc, &wcss->glink_subdev);
> +		qcom_add_ssr_subdev(rproc, &wcss->ssr_subdev, desc->ssr_name);
> +		wcss->sysmon = qcom_add_sysmon_subdev(rproc,
> +						      desc->sysmon_name,
> +						      desc->ssctl_id);

Unless there's good reason I think you should just add these regardless
of version.

> +	}
> +
>  	ret = rproc_add(rproc);
>  	if (ret)
>  		goto free_rproc;
> @@ -605,11 +1150,28 @@ static int q6v5_wcss_remove(struct platform_device *pdev)
>  static const struct wcss_data wcss_ipq8074_res_init = {
>  	.firmware_name = "IPQ8074/q6_fw.mdt",
>  	.crash_reason_smem = 421,
> +	.aon_reset_required = true,
>  	.pas_handover = NULL,
> +	.ops = &q6v5_wcss_ipq8074_ops,
> +};
> +
> +static const struct wcss_data wcss_qcs404_res_init = {
> +	.crash_reason_smem = 421,
> +	.firmware_name = "wcnss.mdt",
> +	.pas_id = 6,

Why does your non-PAS driver have a pas-id?

> +	.version = WCSS_QCS404,
> +	.has_aggre2_clk = false,
> +	.aon_reset_required = false,
> +	.ssr_name = "mpss",
> +	.sysmon_name = "wcnss",
> +	.ssctl_id = 0x12,
> +	.ops = &q6v5_wcss_qcs404_ops,
> +	.pas_handover = q6v5_wcss_pas_handover,
>  };
>  
>  static const struct of_device_id q6v5_wcss_of_match[] = {
> -	{ .compatible = "qcom,ipq8074-wcss-pil", .data = &wcss_ipq8074_res_init },
> +	{ .compatible = "ipq8074-wcss-pil", .data = &wcss_ipq8074_res_init },

You mistakenly dropped qcom, from the compatible here.

> +	{ .compatible = "qcom,qcs404-wcss-non-pas", .data = &wcss_qcs404_res_init },
>  
>  	{ },
>  };

Regards,
Bjorn



[Index of Archives]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Photo Sharing]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux