From: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx> This initial hack powers the q6v5, boots and authenticate the mba and use that to load the mdt and subsequent bXX files. Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx> Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx> --- Changes since v2: - Balancing the rom_clk calls - Moved reset wait to the reset function - Various cleanups per Srinivas review - MODULE_DESCRIPTION and MODULE_LICENSE Changes since v1: - Corrected boot address in relocation case - Using rproc_da_to_va() to clean up mdt loader api - Dynamically allocating scratch space for mdt verification drivers/remoteproc/Kconfig | 12 + drivers/remoteproc/Makefile | 2 + drivers/remoteproc/qcom_mdt_loader.c | 179 +++++++ drivers/remoteproc/qcom_mdt_loader.h | 13 + drivers/remoteproc/qcom_q6v5_pil.c | 916 +++++++++++++++++++++++++++++++++++ 5 files changed, 1122 insertions(+) create mode 100644 drivers/remoteproc/qcom_mdt_loader.c create mode 100644 drivers/remoteproc/qcom_mdt_loader.h create mode 100644 drivers/remoteproc/qcom_q6v5_pil.c diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig index 72e97d7a5209..9ec66d99b978 100644 --- a/drivers/remoteproc/Kconfig +++ b/drivers/remoteproc/Kconfig @@ -77,6 +77,18 @@ config DA8XX_REMOTEPROC It's safe to say n here if you're not interested in multimedia offloading. +config QCOM_MDT_LOADER + tristate + +config QCOM_Q6V5_PIL + tristate "Qualcomm Hexagon V5 Peripherial Image Loader" + depends on OF && ARCH_QCOM + select REMOTEPROC + select QCOM_MDT_LOADER + help + Say y here to support the Qualcomm Peripherial Image Loader for the + Hexagon V5 based remote processors. + config ST_REMOTEPROC tristate "ST remoteproc support" depends on ARCH_STI diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile index 279cb2edc880..92d3758bd15c 100644 --- a/drivers/remoteproc/Makefile +++ b/drivers/remoteproc/Makefile @@ -11,4 +11,6 @@ obj-$(CONFIG_OMAP_REMOTEPROC) += omap_remoteproc.o obj-$(CONFIG_STE_MODEM_RPROC) += ste_modem_rproc.o obj-$(CONFIG_WKUP_M3_RPROC) += wkup_m3_rproc.o obj-$(CONFIG_DA8XX_REMOTEPROC) += da8xx_remoteproc.o +obj-$(CONFIG_QCOM_MDT_LOADER) += qcom_mdt_loader.o +obj-$(CONFIG_QCOM_Q6V5_PIL) += qcom_q6v5_pil.o obj-$(CONFIG_ST_REMOTEPROC) += st_remoteproc.o diff --git a/drivers/remoteproc/qcom_mdt_loader.c b/drivers/remoteproc/qcom_mdt_loader.c new file mode 100644 index 000000000000..114e8e4cef67 --- /dev/null +++ b/drivers/remoteproc/qcom_mdt_loader.c @@ -0,0 +1,179 @@ +/* + * Qualcomm Peripheral Image Loader + * + * Copyright (C) 2016 Linaro Ltd + * Copyright (C) 2015 Sony Mobile Communications Inc + * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/elf.h> +#include <linux/firmware.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/remoteproc.h> +#include <linux/slab.h> + +#include "remoteproc_internal.h" +#include "qcom_mdt_loader.h" + +/** + * qcom_mdt_find_rsc_table() - provide dummy resource table for remoteproc + * @rproc: remoteproc handle + * @fw: firmware header + * @tablesz: outgoing size of the table + * + * Returns a dummy table. + */ +struct resource_table *qcom_mdt_find_rsc_table(struct rproc *rproc, + const struct firmware *fw, + int *tablesz) +{ + static struct resource_table table = { .ver = 1, }; + + *tablesz = sizeof(table); + return &table; +} +EXPORT_SYMBOL_GPL(qcom_mdt_find_rsc_table); + +/** + * qcom_mdt_parse() - extract useful parameters from the mdt header + * @fw: firmware handle + * @fw_addr: optional reference for base of the firmware's memory region + * @fw_size: optional reference for size of the firmware's memory region + * @fw_relocate: optional reference for flagging if the firmware is relocatable + * + * Returns 0 on success, negative errno otherwise. + */ +int qcom_mdt_parse(const struct firmware *fw, phys_addr_t *fw_addr, + size_t *fw_size, bool *fw_relocate) +{ + const struct elf32_phdr *phdrs; + const struct elf32_phdr *phdr; + const struct elf32_hdr *ehdr; + phys_addr_t min_addr = (phys_addr_t)ULLONG_MAX; + phys_addr_t max_addr = 0; + bool relocate = false; + int i; + + ehdr = (struct elf32_hdr *)fw->data; + phdrs = (struct elf32_phdr *)(ehdr + 1); + + for (i = 0; i < ehdr->e_phnum; i++) { + phdr = &phdrs[i]; + + if (phdr->p_type != PT_LOAD) + continue; + + if ((phdr->p_flags & QCOM_MDT_TYPE_MASK) == QCOM_MDT_TYPE_HASH) + continue; + + if (!phdr->p_memsz) + continue; + + if (phdr->p_flags & QCOM_MDT_RELOCATABLE) + relocate = true; + + if (phdr->p_paddr < min_addr) + min_addr = phdr->p_paddr; + + if (phdr->p_paddr + phdr->p_memsz > max_addr) + max_addr = ALIGN(phdr->p_paddr + phdr->p_memsz, SZ_4K); + } + + if (fw_addr) + *fw_addr = min_addr; + if (fw_size) + *fw_size = max_addr - min_addr; + if (fw_relocate) + *fw_relocate = relocate; + + return 0; +} +EXPORT_SYMBOL_GPL(qcom_mdt_parse); + +/** + * qcom_mdt_load() - load the firmware which header is defined in fw + * @rproc: rproc handle + * @fw: frimware object for the header + * @firmware: filename of the firmware, for building .bXX names + * + * Returns 0 on success, negative errno otherwise. + */ +int qcom_mdt_load(struct rproc *rproc, + const struct firmware *fw, + const char *firmware) +{ + const struct elf32_phdr *phdrs; + const struct elf32_phdr *phdr; + const struct elf32_hdr *ehdr; + size_t fw_name_len; + char *fw_name; + void *ptr; + int ret; + int i; + + ehdr = (struct elf32_hdr *)fw->data; + phdrs = (struct elf32_phdr *)(ehdr + 1); + + fw_name_len = strlen(firmware); + if (fw_name_len <= 4) + return -EINVAL; + + fw_name = kstrdup(firmware, GFP_KERNEL); + if (!fw_name) + return -ENOMEM; + + for (i = 0; i < ehdr->e_phnum; i++) { + phdr = &phdrs[i]; + + if (phdr->p_type != PT_LOAD) + continue; + + if ((phdr->p_flags & QCOM_MDT_TYPE_MASK) == QCOM_MDT_TYPE_HASH) + continue; + + if (!phdr->p_memsz) + continue; + + ptr = rproc_da_to_va(rproc, phdr->p_paddr, phdr->p_memsz); + if (!ptr) { + dev_err(&rproc->dev, "segment outside memory range\n"); + ret = -EINVAL; + break; + } + + if (phdr->p_filesz) { + sprintf(fw_name + fw_name_len - 3, "b%02d", i); + ret = request_firmware(&fw, fw_name, &rproc->dev); + if (ret) { + dev_err(&rproc->dev, "failed to load %s\n", + fw_name); + break; + } + + memcpy(ptr, fw->data, fw->size); + + release_firmware(fw); + } + + if (phdr->p_memsz > phdr->p_filesz) + memset(ptr + phdr->p_filesz, 0, phdr->p_memsz - phdr->p_filesz); + } + + kfree(fw_name); + + return ret; +} +EXPORT_SYMBOL_GPL(qcom_mdt_load); + +MODULE_DESCRIPTION("Firmware parser for Qualcomm MDT format"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/remoteproc/qcom_mdt_loader.h b/drivers/remoteproc/qcom_mdt_loader.h new file mode 100644 index 000000000000..c5d7122755b6 --- /dev/null +++ b/drivers/remoteproc/qcom_mdt_loader.h @@ -0,0 +1,13 @@ +#ifndef __QCOM_MDT_LOADER_H__ +#define __QCOM_MDT_LOADER_H__ + +#define QCOM_MDT_TYPE_MASK (7 << 24) +#define QCOM_MDT_TYPE_HASH (2 << 24) +#define QCOM_MDT_RELOCATABLE BIT(27) + +struct resource_table * qcom_mdt_find_rsc_table(struct rproc *rproc, const struct firmware *fw, int *tablesz); +int qcom_mdt_load(struct rproc *rproc, const struct firmware *fw, const char *fw_name); + +int qcom_mdt_parse(const struct firmware *fw, phys_addr_t *fw_addr, size_t *fw_size, bool *fw_relocate); + +#endif diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c new file mode 100644 index 000000000000..fb4c56cc6dfc --- /dev/null +++ b/drivers/remoteproc/qcom_q6v5_pil.c @@ -0,0 +1,916 @@ +/* + * Qualcomm Peripheral Image Loader + * + * Copyright (C) 2016 Linaro Ltd. + * Copyright (C) 2014 Sony Mobile Communications AB + * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_address.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> +#include <linux/remoteproc.h> +#include <linux/reset.h> +#include <linux/soc/qcom/smem.h> +#include <linux/soc/qcom/smem_state.h> + +#include "remoteproc_internal.h" +#include "qcom_mdt_loader.h" + +#include <linux/qcom_scm.h> + +#define MBA_FIRMWARE_NAME "mba.b00" +#define MPSS_FIRMWARE_NAME "modem.mdt" + +#define MPSS_CRASH_REASON_SMEM 421 + +/* RMB Status Register Values */ +#define RMB_PBL_SUCCESS 0x1 + +#define RMB_MBA_XPU_UNLOCKED 0x1 +#define RMB_MBA_XPU_UNLOCKED_SCRIBBLED 0x2 +#define RMB_MBA_META_DATA_AUTH_SUCCESS 0x3 +#define RMB_MBA_AUTH_COMPLETE 0x4 + +/* PBL/MBA interface registers */ +#define RMB_MBA_IMAGE_REG 0x00 +#define RMB_PBL_STATUS_REG 0x04 +#define RMB_MBA_COMMAND_REG 0x08 +#define RMB_MBA_STATUS_REG 0x0C +#define RMB_PMI_META_DATA_REG 0x10 +#define RMB_PMI_CODE_START_REG 0x14 +#define RMB_PMI_CODE_LENGTH_REG 0x18 + +#define RMB_CMD_META_DATA_READY 0x1 +#define RMB_CMD_LOAD_READY 0x2 + +/* QDSP6SS Register Offsets */ +#define QDSP6SS_RESET_REG 0x014 +#define QDSP6SS_GFMUX_CTL_REG 0x020 +#define QDSP6SS_PWR_CTL_REG 0x030 + +/* AXI Halt Register Offsets */ +#define AXI_HALTREQ_REG 0x0 +#define AXI_HALTACK_REG 0x4 +#define AXI_IDLE_REG 0x8 + +#define HALT_ACK_TIMEOUT_MS 100 + +/* QDSP6SS_RESET */ +#define Q6SS_STOP_CORE BIT(0) +#define Q6SS_CORE_ARES BIT(1) +#define Q6SS_BUS_ARES_ENABLE BIT(2) + +/* QDSP6SS_GFMUX_CTL */ +#define Q6SS_CLK_ENABLE BIT(1) + +/* QDSP6SS_PWR_CTL */ +#define Q6SS_L2DATA_SLP_NRET_N_0 BIT(0) +#define Q6SS_L2DATA_SLP_NRET_N_1 BIT(1) +#define Q6SS_L2DATA_SLP_NRET_N_2 BIT(2) +#define Q6SS_L2TAG_SLP_NRET_N BIT(16) +#define Q6SS_ETB_SLP_NRET_N BIT(17) +#define Q6SS_L2DATA_STBY_N BIT(18) +#define Q6SS_SLP_RET_N BIT(19) +#define Q6SS_CLAMP_IO BIT(20) +#define QDSS_BHS_ON BIT(21) +#define QDSS_LDO_BYP BIT(22) + +struct q6v5 { + struct device *dev; + struct rproc *rproc; + + void __iomem *reg_base; + void __iomem *rmb_base; + + struct regmap *halt_map; + u32 halt_q6; + u32 halt_modem; + u32 halt_nc; + + struct reset_control *mss_restart; + + struct qcom_smem_state *state; + unsigned stop_bit; + + struct regulator_bulk_data supply[4]; + + struct clk *ahb_clk; + struct clk *axi_clk; + struct clk *rom_clk; + + struct completion start_done; + struct completion stop_done; + bool running; + + phys_addr_t mba_phys; + void *mba_region; + size_t mba_size; + + phys_addr_t mpss_phys; + phys_addr_t mpss_reloc; + void *mpss_region; + size_t mpss_size; +}; + +enum { + Q6V5_SUPPLY_CX, + Q6V5_SUPPLY_MX, + Q6V5_SUPPLY_MSS, + Q6V5_SUPPLY_PLL, +}; + +static int q6v5_regulator_init(struct q6v5 *qproc) +{ + int ret; + + qproc->supply[Q6V5_SUPPLY_CX].supply = "cx"; + qproc->supply[Q6V5_SUPPLY_MX].supply = "mx"; + qproc->supply[Q6V5_SUPPLY_MSS].supply = "mss"; + qproc->supply[Q6V5_SUPPLY_PLL].supply = "pll"; + + ret = devm_regulator_bulk_get(qproc->dev, + ARRAY_SIZE(qproc->supply), qproc->supply); + if (ret < 0) { + dev_err(qproc->dev, "failed to get supplies\n"); + return ret; + } + + regulator_set_load(qproc->supply[Q6V5_SUPPLY_CX].consumer, 100000); + regulator_set_load(qproc->supply[Q6V5_SUPPLY_MSS].consumer, 100000); + regulator_set_load(qproc->supply[Q6V5_SUPPLY_PLL].consumer, 10000); + + return 0; +} + +static int q6v5_regulator_enable(struct q6v5 *qproc) +{ + struct regulator *mss = qproc->supply[Q6V5_SUPPLY_MSS].consumer; + struct regulator *mx = qproc->supply[Q6V5_SUPPLY_MX].consumer; + int ret; + + /* TODO: Q6V5_SUPPLY_CX is supposed to be set to super-turbo here */ + + ret = regulator_set_voltage(mx, 1050000, INT_MAX); + if (ret) + return ret; + + regulator_set_voltage(mss, 1000000, 1150000); + + return regulator_bulk_enable(ARRAY_SIZE(qproc->supply), qproc->supply); +} + +static void q6v5_regulator_disable(struct q6v5 *qproc) +{ + struct regulator *mss = qproc->supply[Q6V5_SUPPLY_MSS].consumer; + struct regulator *mx = qproc->supply[Q6V5_SUPPLY_MX].consumer; + + /* TODO: Q6V5_SUPPLY_CX corner votes should be released */ + + regulator_bulk_disable(ARRAY_SIZE(qproc->supply), qproc->supply); + regulator_set_voltage(mx, 0, INT_MAX); + regulator_set_voltage(mss, 0, 1150000); +} + +static int q6v5_load(struct rproc *rproc, const struct firmware *fw) +{ + struct q6v5 *qproc = rproc->priv; + + memcpy(qproc->mba_region, fw->data, fw->size); + + return 0; +} + +static const struct rproc_fw_ops q6v5_fw_ops = { + .find_rsc_table = qcom_mdt_find_rsc_table, + .load = q6v5_load, +}; + +static int q6v5_rmb_pbl_wait(struct q6v5 *qproc, int ms) +{ + unsigned long timeout; + s32 val; + + timeout = jiffies + msecs_to_jiffies(ms); + for (;;) { + val = readl(qproc->rmb_base + RMB_PBL_STATUS_REG); + if (val) + break; + + if (time_after(jiffies, timeout)) + return -ETIMEDOUT; + + msleep(1); + } + + return val; +} + +static int q6v5_rmb_mba_wait(struct q6v5 *qproc, u32 status, int ms) +{ + + unsigned long timeout; + s32 val; + + timeout = jiffies + msecs_to_jiffies(ms); + for (;;) { + val = readl(qproc->rmb_base + RMB_MBA_STATUS_REG); + if (val < 0) + break; + + if (!status && val) + break; + else if (status && val == status) + break; + + if (time_after(jiffies, timeout)) + return -ETIMEDOUT; + + msleep(1); + } + + return val; +} + +static int q6v5proc_reset(struct q6v5 *qproc) +{ + u32 val; + int ret; + + /* Assert resets, stop core */ + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); + + /* Enable power block headswitch, and wait for it to stabilize */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= QDSS_BHS_ON | QDSS_LDO_BYP; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + udelay(1); + + /* + * Turn on memories. L2 banks should be done individually + * to minimize inrush current. + */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_SLP_RET_N | Q6SS_L2TAG_SLP_NRET_N | + Q6SS_ETB_SLP_NRET_N | Q6SS_L2DATA_STBY_N; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_L2DATA_SLP_NRET_N_2; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_L2DATA_SLP_NRET_N_1; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_L2DATA_SLP_NRET_N_0; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + + /* Remove IO clamp */ + val &= ~Q6SS_CLAMP_IO; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + + /* Bring core out of reset */ + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); + val &= ~Q6SS_CORE_ARES; + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); + + /* Turn on core clock */ + val = readl(qproc->reg_base + QDSP6SS_GFMUX_CTL_REG); + val |= Q6SS_CLK_ENABLE; + writel(val, qproc->reg_base + QDSP6SS_GFMUX_CTL_REG); + + /* Start core execution */ + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); + val &= ~Q6SS_STOP_CORE; + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); + + /* Wait for PBL status */ + ret = q6v5_rmb_pbl_wait(qproc, 1000); + if (ret == -ETIMEDOUT) { + dev_err(qproc->dev, "PBL boot timed out\n"); + } else if (ret != RMB_PBL_SUCCESS) { + dev_err(qproc->dev, "PBL returned unexpected status %d\n", ret); + ret = -EINVAL; + } else { + ret = 0; + } + + return ret; +} + +static void q6v5proc_halt_axi_port(struct q6v5 *qproc, + struct regmap *halt_map, + u32 offset) +{ + unsigned long timeout; + unsigned int val; + int ret; + + /* Check if we're already idle */ + ret = regmap_read(halt_map, offset + AXI_IDLE_REG, &val); + if (!ret && val) + return; + + /* Assert halt request */ + regmap_write(halt_map, offset + AXI_HALTREQ_REG, 1); + + /* Wait for halt */ + timeout = jiffies + msecs_to_jiffies(HALT_ACK_TIMEOUT_MS); + for (;;) { + ret = regmap_read(halt_map, offset + AXI_HALTACK_REG, &val); + if (ret || val || time_after(jiffies, timeout)) + break; + + msleep(1); + } + + ret = regmap_read(halt_map, offset + AXI_IDLE_REG, &val); + if (ret || !val) + dev_err(qproc->dev, "port failed halt\n"); + + /* Clear halt request (port will remain halted until reset) */ + regmap_write(halt_map, offset + AXI_HALTREQ_REG, 0); +} + +static int q6v5_mpss_init_image(struct q6v5 *qproc, const struct firmware *fw) +{ + DEFINE_DMA_ATTRS(attrs); + dma_addr_t phys; + void *ptr; + int ret; + + dma_set_attr(DMA_ATTR_FORCE_CONTIGUOUS, &attrs); + ptr = dma_alloc_attrs(qproc->dev, fw->size, &phys, GFP_KERNEL, &attrs); + if (!ptr) { + dev_err(qproc->dev, "failed to allocate mdt buffer\n"); + return -ENOMEM; + } + + memcpy(ptr, fw->data, fw->size); + + writel(phys, qproc->rmb_base + RMB_PMI_META_DATA_REG); + writel(RMB_CMD_META_DATA_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG); + + ret = q6v5_rmb_mba_wait(qproc, RMB_MBA_META_DATA_AUTH_SUCCESS, 1000); + if (ret == -ETIMEDOUT) + dev_err(qproc->dev, "MPSS header authentication timed out\n"); + else if (ret < 0) + dev_err(qproc->dev, "MPSS header authentication failed: %d\n", ret); + + dma_free_attrs(qproc->dev, fw->size, ptr, phys, &attrs); + + return ret < 0 ? ret : 0; +} + +static int q6v5_mpss_validate(struct q6v5 *qproc, const struct firmware *fw) +{ + const struct elf32_phdr *phdrs; + const struct elf32_phdr *phdr; + struct elf32_hdr *ehdr; + phys_addr_t boot_addr; + phys_addr_t fw_addr; + bool relocate; + size_t size; + u32 val; + int ret; + int i; + + ret = qcom_mdt_parse(fw, &fw_addr, NULL, &relocate); + if (ret) { + dev_err(qproc->dev, "failed to parse mdt header\n"); + return ret; + } + + if (relocate) + boot_addr = qproc->mpss_phys; + else + boot_addr = fw_addr; + + ehdr = (struct elf32_hdr *)fw->data; + phdrs = (struct elf32_phdr *)(ehdr + 1); + for (i = 0; i < ehdr->e_phnum; i++, phdr++) { + phdr = &phdrs[i]; + + if (phdr->p_type != PT_LOAD) + continue; + + if ((phdr->p_flags & QCOM_MDT_TYPE_MASK) == QCOM_MDT_TYPE_HASH) + continue; + + if (!phdr->p_memsz) + continue; + + size = readl(qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG); + if (!size) { + writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG); + writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG); + } + + size += phdr->p_memsz; + writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG); + } + + val = readl(qproc->rmb_base + RMB_MBA_STATUS_REG); + return val < 0 ? val : 0; +} + +static int q6v5_mpss_load(struct q6v5 *qproc) +{ + const struct firmware *fw; + phys_addr_t fw_addr; + bool relocate; + int ret; + + ret = request_firmware(&fw, MPSS_FIRMWARE_NAME, qproc->dev); + if (ret < 0) { + dev_err(qproc->dev, "unable to load " MPSS_FIRMWARE_NAME "\n"); + return ret; + } + + ret = qcom_mdt_parse(fw, &fw_addr, NULL, &relocate); + if (ret) { + dev_err(qproc->dev, "failed to parse mdt header\n"); + goto release_firmware; + } + + if (relocate) + qproc->mpss_reloc = fw_addr; + + /* Initialize the RMB validator */ + writel(0, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG); + + ret = q6v5_mpss_init_image(qproc, fw); + if (ret) + goto release_firmware; + + ret = qcom_mdt_load(qproc->rproc, fw, MPSS_FIRMWARE_NAME); + if (ret) + goto release_firmware; + + ret = q6v5_mpss_validate(qproc, fw); + if (ret) + goto release_firmware; + + ret = q6v5_rmb_mba_wait(qproc, RMB_MBA_AUTH_COMPLETE, 10000); + if (ret == -ETIMEDOUT) + dev_err(qproc->dev, "MPSS authentication timed out\n"); + else if (ret < 0) + dev_err(qproc->dev, "MPSS authentication failed: %d\n", ret); + +release_firmware: + release_firmware(fw); + + return ret < 0 ? ret : 0; +} + +static int q6v5_start(struct rproc *rproc) +{ + struct q6v5 *qproc = (struct q6v5 *)rproc->priv; + int ret; + + ret = q6v5_regulator_enable(qproc); + if (ret) { + dev_err(qproc->dev, "failed to enable supplies\n"); + return ret; + } + + ret = reset_control_deassert(qproc->mss_restart); + if (ret) { + dev_err(qproc->dev, "failed to deassert mss restart\n"); + goto disable_vdd; + } + + ret = clk_prepare_enable(qproc->ahb_clk); + if (ret) + goto assert_reset; + + ret = clk_prepare_enable(qproc->axi_clk); + if (ret) + goto disable_ahb_clk; + + ret = clk_prepare_enable(qproc->rom_clk); + if (ret) + goto disable_axi_clk; + + writel(qproc->mba_phys, qproc->rmb_base + RMB_MBA_IMAGE_REG); + + ret = q6v5proc_reset(qproc); + if (ret) + goto halt_axi_ports; + + ret = q6v5_rmb_mba_wait(qproc, 0, 5000); + if (ret == -ETIMEDOUT) { + dev_err(qproc->dev, "MBA boot timed out\n"); + goto halt_axi_ports; + } else if (ret != RMB_MBA_XPU_UNLOCKED && + ret != RMB_MBA_XPU_UNLOCKED_SCRIBBLED) { + dev_err(qproc->dev, "MBA returned unexpected status %d\n", ret); + ret = -EINVAL; + goto halt_axi_ports; + } + + dev_info(qproc->dev, "MBA booted, loading mpss\n"); + + ret = q6v5_mpss_load(qproc); + if (ret) + goto halt_axi_ports; + + ret = wait_for_completion_timeout(&qproc->start_done, + msecs_to_jiffies(5000)); + if (ret == 0) { + dev_err(qproc->dev, "start timed out\n"); + ret = -ETIMEDOUT; + goto halt_axi_ports; + } + + qproc->running = true; + + /* TODO: All done, release the handover resources */ + + return 0; + +halt_axi_ports: + q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6); + q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); + q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); + + clk_disable_unprepare(qproc->rom_clk); +disable_axi_clk: + clk_disable_unprepare(qproc->axi_clk); +disable_ahb_clk: + clk_disable_unprepare(qproc->ahb_clk); +assert_reset: + reset_control_assert(qproc->mss_restart); +disable_vdd: + q6v5_regulator_disable(qproc); + + return ret; +} + +static int q6v5_stop(struct rproc *rproc) +{ + struct q6v5 *qproc = (struct q6v5 *)rproc->priv; + int ret; + + qproc->running = false; + + qcom_smem_state_update_bits(qproc->state, + BIT(qproc->stop_bit), BIT(qproc->stop_bit)); + + ret = wait_for_completion_timeout(&qproc->stop_done, + msecs_to_jiffies(5000)); + if (ret == 0) + dev_err(qproc->dev, "timed out on wait\n"); + + qcom_smem_state_update_bits(qproc->state, BIT(qproc->stop_bit), 0); + + q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6); + q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); + q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); + + reset_control_assert(qproc->mss_restart); + clk_disable_unprepare(qproc->rom_clk); + clk_disable_unprepare(qproc->axi_clk); + clk_disable_unprepare(qproc->ahb_clk); + q6v5_regulator_disable(qproc); + + return 0; +} + +static void *q6v5_da_to_va(struct rproc *rproc, u64 da, int len) +{ + struct q6v5 *qproc = rproc->priv; + int offset; + + offset = da - qproc->mpss_reloc; + if (offset < 0 || offset + len > qproc->mpss_size) + return NULL; + + return qproc->mpss_region + offset; +} + +static const struct rproc_ops q6v5_ops = { + .start = q6v5_start, + .stop = q6v5_stop, + .da_to_va = q6v5_da_to_va, +}; + +static irqreturn_t q6v5_wdog_interrupt(int irq, void *dev) +{ + struct q6v5 *qproc = dev; + size_t len; + char *msg; + + /* Sometimes the stop triggers a watchdog rather than a stop-ack */ + if (!qproc->running) { + complete(&qproc->stop_done); + return IRQ_HANDLED; + } + + msg = qcom_smem_get(QCOM_SMEM_HOST_ANY, MPSS_CRASH_REASON_SMEM, &len); + if (!IS_ERR(msg) && len > 0 && msg[0]) + dev_err(qproc->dev, "watchdog received: %s\n", msg); + else + dev_err(qproc->dev, "watchdog without message\n"); + + rproc_report_crash(qproc->rproc, RPROC_WATCHDOG); + + if (!IS_ERR(msg)) + msg[0] = '\0'; + + return IRQ_HANDLED; +} + +static irqreturn_t q6v5_fatal_interrupt(int irq, void *dev) +{ + struct q6v5 *qproc = dev; + size_t len; + char *msg; + + msg = qcom_smem_get(QCOM_SMEM_HOST_ANY, MPSS_CRASH_REASON_SMEM, &len); + if (!IS_ERR(msg) && len > 0 && msg[0]) + dev_err(qproc->dev, "fatal error received: %s\n", msg); + else + dev_err(qproc->dev, "fatal error without message\n"); + + rproc_report_crash(qproc->rproc, RPROC_FATAL_ERROR); + + if (!IS_ERR(msg)) + msg[0] = '\0'; + + return IRQ_HANDLED; +} + +static irqreturn_t q6v5_handover_interrupt(int irq, void *dev) +{ + struct q6v5 *qproc = dev; + + complete(&qproc->start_done); + return IRQ_HANDLED; +} + +static irqreturn_t q6v5_stop_ack_interrupt(int irq, void *dev) +{ + struct q6v5 *qproc = dev; + + complete(&qproc->stop_done); + return IRQ_HANDLED; +} + +static int q6v5_init_mem(struct q6v5 *qproc, struct platform_device *pdev) +{ + struct of_phandle_args args; + struct resource *res; + int ret; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qdsp6"); + qproc->reg_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(qproc->reg_base)) { + dev_err(qproc->dev, "failed to get qdsp6_base\n"); + return PTR_ERR(qproc->reg_base); + } + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rmb"); + qproc->rmb_base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(qproc->rmb_base)) { + dev_err(qproc->dev, "failed to get rmb_base\n"); + return PTR_ERR(qproc->rmb_base); + } + + ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node, + "qcom,halt-regs", 3, 0, &args); + if (ret < 0) { + dev_err(&pdev->dev, "failed to parse qcom,halt-regs\n"); + return -EINVAL; + } + + qproc->halt_map = syscon_node_to_regmap(args.np); + of_node_put(args.np); + if (IS_ERR(qproc->halt_map)) + return PTR_ERR(qproc->halt_map); + + qproc->halt_q6 = args.args[0]; + qproc->halt_modem = args.args[1]; + qproc->halt_nc = args.args[2]; + + return 0; +} + +static int q6v5_init_clocks(struct q6v5 *qproc) +{ + qproc->ahb_clk = devm_clk_get(qproc->dev, "iface"); + if (IS_ERR(qproc->ahb_clk)) { + dev_err(qproc->dev, "failed to get iface clock\n"); + return PTR_ERR(qproc->ahb_clk); + } + + qproc->axi_clk = devm_clk_get(qproc->dev, "bus"); + if (IS_ERR(qproc->axi_clk)) { + dev_err(qproc->dev, "failed to get bus clock\n"); + return PTR_ERR(qproc->axi_clk); + } + + qproc->rom_clk = devm_clk_get(qproc->dev, "mem"); + if (IS_ERR(qproc->rom_clk)) { + dev_err(qproc->dev, "failed to get mem clock\n"); + return PTR_ERR(qproc->rom_clk); + } + + return 0; +} + +static int q6v5_init_reset(struct q6v5 *qproc) +{ + qproc->mss_restart = devm_reset_control_get(qproc->dev, NULL); + if (IS_ERR(qproc->mss_restart)) { + dev_err(qproc->dev, "failed to acquire mss restart\n"); + return PTR_ERR(qproc->mss_restart); + } + + return 0; +} + +static int q6v5_request_irq(struct q6v5 *qproc, + struct platform_device *pdev, + const char *name, + irq_handler_t thread_fn) +{ + int ret; + + ret = platform_get_irq_byname(pdev, name); + if (ret < 0) { + dev_err(&pdev->dev, "no %s IRQ defined\n", name); + return ret; + } + + ret = devm_request_threaded_irq(&pdev->dev, ret, + NULL, thread_fn, + IRQF_TRIGGER_RISING | IRQF_ONESHOT, + "q6v5", qproc); + if (ret) + dev_err(&pdev->dev, "request %s IRQ failed\n", name); + + return ret; +} + +static int q6v5_alloc_memory_region(struct q6v5 *qproc) +{ + struct device_node *child; + struct device_node *node; + struct resource r; + int ret; + + child = of_get_child_by_name(qproc->dev->of_node, "mba"); + node = of_parse_phandle(child, "memory-region", 0); + ret = of_address_to_resource(node, 0, &r); + if (ret) { + dev_err(qproc->dev, "unable to resolve mba region\n"); + return ret; + } + + qproc->mba_phys = r.start; + qproc->mba_size = resource_size(&r); + qproc->mba_region = devm_ioremap_wc(qproc->dev, qproc->mba_phys, qproc->mba_size); + if (!qproc->mba_region) { + dev_err(qproc->dev, "unable to map memory region: %pa+%zx\n", + &r.start, qproc->mba_size); + return -EBUSY; + } + + child = of_get_child_by_name(qproc->dev->of_node, "mpss"); + node = of_parse_phandle(child, "memory-region", 0); + ret = of_address_to_resource(node, 0, &r); + if (ret) { + dev_err(qproc->dev, "unable to resolve mpss region\n"); + return ret; + } + + qproc->mpss_phys = qproc->mpss_reloc = r.start; + qproc->mpss_size = resource_size(&r); + qproc->mpss_region = devm_ioremap_wc(qproc->dev, qproc->mpss_phys, qproc->mpss_size); + if (!qproc->mpss_region) { + dev_err(qproc->dev, "unable to map memory region: %pa+%zx\n", + &r.start, qproc->mpss_size); + return -EBUSY; + } + + return 0; +} + +static int q6v5_probe(struct platform_device *pdev) +{ + struct q6v5 *qproc; + struct rproc *rproc; + int ret; + + rproc = rproc_alloc(&pdev->dev, pdev->name, &q6v5_ops, + MBA_FIRMWARE_NAME, sizeof(*qproc)); + if (!rproc) { + dev_err(&pdev->dev, "failed to allocate rproc\n"); + return -ENOMEM; + } + + rproc->fw_ops = &q6v5_fw_ops; + + qproc = (struct q6v5 *)rproc->priv; + qproc->dev = &pdev->dev; + qproc->rproc = rproc; + platform_set_drvdata(pdev, qproc); + + init_completion(&qproc->start_done); + init_completion(&qproc->stop_done); + + ret = q6v5_init_mem(qproc, pdev); + if (ret) + goto free_rproc; + + ret = q6v5_alloc_memory_region(qproc); + if (ret) + goto free_rproc; + + ret = q6v5_init_clocks(qproc); + if (ret) + goto free_rproc; + + ret = q6v5_regulator_init(qproc); + if (ret) + goto free_rproc; + + ret = q6v5_init_reset(qproc); + if (ret) + goto free_rproc; + + ret = q6v5_request_irq(qproc, pdev, "wdog", q6v5_wdog_interrupt); + if (ret < 0) + goto free_rproc; + + ret = q6v5_request_irq(qproc, pdev, "fatal", q6v5_fatal_interrupt); + if (ret < 0) + goto free_rproc; + + ret = q6v5_request_irq(qproc, pdev, "handover", q6v5_handover_interrupt); + if (ret < 0) + goto free_rproc; + + ret = q6v5_request_irq(qproc, pdev, "stop-ack", q6v5_stop_ack_interrupt); + if (ret < 0) + goto free_rproc; + + qproc->state = qcom_smem_state_get(&pdev->dev, "stop", &qproc->stop_bit); + if (IS_ERR(qproc->state)) + goto free_rproc; + + ret = rproc_add(rproc); + if (ret) + goto free_rproc; + + return 0; + +free_rproc: + rproc_put(rproc); + + return ret; +} + +static int q6v5_remove(struct platform_device *pdev) +{ + struct q6v5 *qproc = platform_get_drvdata(pdev); + + rproc_del(qproc->rproc); + rproc_put(qproc->rproc); + + return 0; +} + +static const struct of_device_id q6v5_of_match[] = { + { .compatible = "qcom,q6v5-pil", }, + { }, +}; + +static struct platform_driver q6v5_driver = { + .probe = q6v5_probe, + .remove = q6v5_remove, + .driver = { + .name = "qcom-q6v5-pil", + .of_match_table = q6v5_of_match, + }, +}; +module_platform_driver(q6v5_driver); + +MODULE_DESCRIPTION("Peripheral Image Loader for Hexagon"); +MODULE_LICENSE("GPL v2"); -- 2.5.0 -- To unsubscribe from this list: send the line "unsubscribe linux-remoteproc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html