README with description of major sysfs entries.
Signed-off-by: Roman Pen <roman.penyaev@xxxxxxxxxxxxxxxx>
Signed-off-by: Danil Kipnis <danil.kipnis@xxxxxxxxxxxxxxxx>
Cc: Jack Wang <jinpu.wang@xxxxxxxxxxxxxxxx>
---
drivers/block/ibnbd/README | 299 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 299 insertions(+)
create mode 100644 drivers/block/ibnbd/README
diff --git a/drivers/block/ibnbd/README b/drivers/block/ibnbd/README
new file mode 100644
index 000000000000..bbaddd02c1c5
--- /dev/null
+++ b/drivers/block/ibnbd/README
@@ -0,0 +1,299 @@
+***************************************
+Infiniband Network Block Device (IBNBD)
+***************************************
+
+Introduction
+------------
+
+IBNBD (InfiniBand Network Block Device) is a pair of kernel modules
+(client and server) that allow for remote access of a block device on
+the server over IBTRS protocol using the RDMA (InfiniBand, RoCE, iWarp)
+transport. After being mapped, the remote block devices can be accessed
+on the client side as local block devices.
+
+I/O is transfered between client and server by the IBTRS transport
+modules. The administration of IBNBD and IBTRS modules is done via
+sysfs entries.
+
+Requirements
+------------
+
+ IBTRS kernel modules
+
+Quick Start
+-----------
+
+Server side:
+ # modprobe ibnbd_server
+
+Client side:
+ # modprobe ibnbd_client
+ # echo "sessname=blya path=ip:10.50.100.66 device_path=/dev/ram0" > \
+ /sys/devices/virtual/ibnbd-client/ctl/map_device
+
+ Where "sessname=" is a session name, a string to identify the session
+ on client and on server sides; "path=" is a destination IP address or
+ a pair of a source and a destination IPs, separated by comma. Multiple
+ "path=" options can be specified in order to use multipath (see IBTRS
+ description for details); "device_path=" is the block device to be
+ mapped from the server side. After the session to the server machine is
+ established, the mapped device will appear on the client side under
+ /dev/ibnbd<N>.
+
+
+======================
+Client Sysfs Interface
+======================
+
+All sysfs files that are not read-only provide the usage information on read:
+
+Example:
+ # cat /sys/devices/virtual/ibnbd-client/ctl/map_device
+
+ > Usage: echo "sessname=<name of the ibtrs session> path=<[srcaddr,]dstaddr>
+ > [path=<[srcaddr,]dstaddr>] device_path=<full path on remote side>
+ > [access_mode=<ro|rw|migration>]
+ > [io_mode=<fileio|blockio>]" > map_device
+ >
+ > addr ::= [ ip:<ipv4> | ip:<ipv6> | gid:<gid> ]
+
+Entries under /sys/devices/virtual/ibnbd-client/ctl/
+=======================================
+
+map_device (RW)
+---------------
+
+Expected format is the following:
+
+ sessname=<name of the ibtrs session>
+ path=<[srcaddr,]dstaddr> [path=<[srcaddr,]dstaddr> ...]
+ device_path=<full path on remote side>
+ [access_mode=<ro|rw|migration>]
+ [io_mode=<fileio|blockio>]
+
+Where:
+
+sessname: accepts a string not bigger than 256 chars, which identifies
+ a given session on the client and on the server.
+ I.e. "clt_hostname-srv_hostname" could be a natural choice.
+
+path: describes a connection between the client and the server by
+ specifying destination and, when required, the source address.
+ The addresses are to be provided in the following format:
+
+ ip:<IPv6>
+ ip:<IPv4>
+ gid:<GID>
+
+ for example:
+
+ path=ip:10.0.0.66
+ The single addr is treated as the destination.
+ The connection will be established to this
+ server from any client IP address.
+
+ path=ip:10.0.0.66,ip:10.0.1.66
+ First addr is the source address and the second
+ is the destination.
+
+ If multiple "path=" options are specified multiple connection
+ will be established and data will be sent according to
+ the selected multipath policy (see IBTRS mp_policy sysfs entry
+ description).
+
+device_path: Path to the block device on the server side. Path is specified
+ relative to the directory on server side configured in the
+ 'dev_search_path' module parameter of the ibnbd_server.
+ The ibnbd_server prepends the <device_path> received from client
+ with <dev_search_path> and tries to open the
+ <dev_search_path>/<device_path> block device. On success,
+ a /dev/ibnbd<N> device file, a /sys/block/ibnbd_client/ibnbd<N>/
+ directory and an entry in /sys/devices/virtual/ibnbd-client/ctl/devices
+ will be created.
+
+ If 'dev_search_path' contains '%SESSNAME%', then each session can
+ have different devices namespace, e.g. server was configured with
+ the following parameter "dev_search_path=/run/ibnbd-devs/%SESSNAME%",
+ client has this string "sessname=blya device_path=sda", then server
+ will try to open: /run/ibnbd-devs/blya/sda.
+
+access_mode: the access_mode parameter specifies if the device is to be
+ mapped as "ro" read-only or "rw" read-write. The server allows
+ a device to be exported in rw mode only once. The "migration"
+ access mode has to be specified if a second mapping in read-write
+ mode is desired.
+
+ By default "rw" is used.
+
+io_mode: the io_mode parameter specifies if the device on the server
+ will be opened as block device "blockio" or as file "fileio".
+ When the device is opened as file, the VFS page cache is used
+ for read I/O operations, write I/O operations bypass the page
+ cache and go directly to disk (except meta updates, like file
+ access time).
+
+ By default "blockio" mode is used.
+
+Exit Codes:
+
+If the device is already mapped it will fail with EEXIST. If the input
+has an invalid format it will return EINVAL. If the device path cannot
+be found on the server, it will fail with ENOENT.
+
+Finding device file after mapping
+---------------------------------
+
+After mapping, the device file can be found by:
+ o The symlink /sys/devices/virtual/ibnbd-client/ctl/devices/<device_id>
+ points to /sys/block/<dev-name>. The last part of the symlink destination
+ is the same as the device name. By extracting the last part of the
+ path the path to the device /dev/<dev-name> can be build.
+
+ o /dev/block/$(cat /sys/devices/virtual/ibnbd-client/ctl/devices/<device_id>/dev)
+
+How to find the <device_id> of the device is described on the next
+section.
+
+Entries under /sys/devices/virtual/ibnbd-client/ctl/devices/
+============================================================
+
+For each device mapped on the client a new symbolic link is created as
+/sys/devices/virtual/ibnbd-client/ctl/devices/<device_id>, which points
+to the block device created by ibnbd (/sys/block/ibnbd<N>/).
+The <device_id> of each device is created as follows:
+
+- If the 'device_path' provided during mapping contains slashes ("/"),
+ they are replaced by exclamation mark ("!") and used as as the
+ <device_id>. Otherwise, the <device_id> will be the same as the
+ "device_path" provided.
+
+Entries under /sys/block/ibnbd<N>/ibnbd_client/
+===============================================
+
+unmap_device (RW)
+-----------------
+
+To unmap a volume, "normal" or "force" has to be written to:
+ /sys/block/ibnbd<N>/ibnbd_client/unmap_device
+
+When "normal" is used, the operation will fail with EBUSY if any process
+is using the device. When "force" is used, the device is also unmapped
+when device is in use. All I/Os that are in progress will fail.
+
+Example:
+
+ # echo "normal" > /sys/block/ibnbd0/ibnbd/unmap_device
+
+state (RO)
+----------
+
+The file contains the current state of the block device. The state file
+returns "open" when the device is successfully mapped from the server
+and accepting I/O requests. When the connection to the server gets
+disconnected in case of an error (e.g. link failure), the state file
+returns "closed" and all I/O requests submitted to it will fail with -EIO.
+
+session (RO)
+------------
+
+IBNBD uses IBTRS session to transport the data between client and
+server. The entry "session" contains the name of the session, that
+was used to establish the IBTRS session. It's the same name that
+was passed as server parameter to the map_device entry.
+
+mapping_path (RO)
+-----------------
+
+Contains the path that was passed as "device_path" to the map_device
+operation.
+
+======================
+Server Sysfs Interface
+======================
+
+Entries under /sys/devices/virtual/ibnbd-server/ctl/
+====================================================
+
+When a client maps a device, a directory entry with the name of the
+block device is created under /sys/devices/virtual/ibnbd-server/ctl/devices/.
+
+Entries under /sys/devices/virtual/ibnbd-server/ctl/devices/<device_name>/
+==========================================================================
+
+block_dev (link)
+---------------
+
+Is a symlink to the sysfs entry of the exported device.
+
+Example:
+
+ block_dev -> ../../../../devices/virtual/block/ram0
+
+Entries under /sys/devices/virtual/ibnbd-server/ctl/devices/<device_name>/sessions/
+===================================================================================
+
+For each client a particular device is exported to, following directory will be
+created:
+
+/sys/devices/virtual/ibnbd-server/ctl/devices/<device_name>/sessions/<session-name>/
+
+When the device is unmapped by that client, the directory will be removed.
+
+Entries under /sys/devices/virtual/ibnbd-server/ctl/devices/<device_name>/sessions/<session-name>
+=================================================================================================
+
+read_only (RO)
+--------------
+
+Contains '1' if device is mapped read-only, otherwise '0'.
+
+mapping_path (RO)
+-----------------
+
+Contains the relative device path provided by the user during mapping.
+
+==============================
+IBNBD-Server Module Parameters
+==============================
+
+dev_search_path
+---------------
+
+When a device is mapped from the client, the server generates the path
+to the block device on the server side by concatenating dev_search_path
+and the "device_path" that was specified in the map_device operation.
+
+The default dev_search_path is: "/".
+
+dev_search_path option can also contain %SESSNAME% in order to provide
+different deviec namespaces for different sessions. See "device_path"
+option for details.
+
+==============================
+Protocol (ibnbd/ibnbd-proto.h)
+==============================
+
+1. Before mapping first device from a given server, client sends an
+IBNBD_MSG_SESS_INFO to the server. Server responds with
+IBNBD_MSG_SESS_INFO_RSP. Currently the messages only contain the protocol
+version for backward compatibility.
+
+2. Client requests to open a device by sending IBNBD_MSG_OPEN message. This
+contains the path to the device, access mode (read-only or writable), and
+io_mode which specifies if the device should be opened as block device or
+using file io. Server responds to the message with IBNBD_MSG_OPEN_RSP. This
+contains a 32 bit device id to be used for IOs and device "geometry" related
+information: side, max_hw_sectors, etc.
+
+3. Client attaches IBNBD_MSG_IO to each IO message send to a device. This
+message contains device id, provided by server in his ibnbd_msg_open_rsp,
+sector to be accessed, read-write flags and bi_size.
+
+4. Client closes a device by sending IBNBD_MSG_CLOSE which contains only the
+device id provided by the server.
+
+
+Contact
+-------
+
+Mailing list: "IBNBD/IBTRS Storage Team" <ibnbd@xxxxxxxxxxxxxxxx>
--
2.13.1
--
To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
