On Thu, Mar 15, 2018 at 08:32:02AM -0400, Hal Rosenstock wrote:
> On 3/15/2018 8:01 AM, Hal Rosenstock wrote:
> > On 3/15/2018 5:02 AM, Honggang LI wrote:
> >> From: Honggang Li <honli@xxxxxxxxxx>
> >>
> >> commit f1b65df5a232 ("IB/mlx5: Add support for active_width and
> >> active_speed in RoCE"). Before this patch applied, the mlx5_ib
> >> driver set default active_width and active_speed to IB_WIDTH_4X
> >> and IB_SPEED_QDR.
> >>
> >> When the RoCE port is down, the RoCE port did not negotiate the
> >> active width with remote side. The active width is zero. If run
> >> ibstat to require the port status, ibstat will panic as it read
> >> invalid width from sys file.
> >>
> >> Signed-off-by: Honggang Li <honli@xxxxxxxxxx>
> >> ---
> >> drivers/infiniband/core/sysfs.c | 15 +++++++++++----
> >> 1 file changed, 11 insertions(+), 4 deletions(-)
> >>
> >> diff --git a/drivers/infiniband/core/sysfs.c b/drivers/infiniband/core/sysfs.c
> >> index cf36ff1f0068..722e4571f4d2 100644
> >> --- a/drivers/infiniband/core/sysfs.c
> >> +++ b/drivers/infiniband/core/sysfs.c
> >> @@ -240,6 +240,7 @@ static ssize_t rate_show(struct ib_port *p, struct port_attribute *unused,
> >> struct ib_port_attr attr;
> >> char *speed = "";
> >> int rate; /* in deci-Gb/sec */
> >> + int width;
> >> ssize_t ret;
> >>
> >> ret = ib_query_port(p->ibdev, p->port_num, &attr);
> >> @@ -278,13 +279,19 @@ static ssize_t rate_show(struct ib_port *p, struct port_attribute *unused,
> >> break;
> >> }
> >>
> >> - rate *= ib_width_enum_to_int(attr.active_width);
> >> - if (rate < 0)
> >> - return -EINVAL;
> >> + width = ib_width_enum_to_int(attr.active_width);
> >> + if (width < 0) {
> >> + if (attr.state != IB_PORT_ACTIVE)
> >
> > Link width is valid in any PortState other than Down so I think that
> > this check should be:
> > if (attr.state != IB_PORT_DOWN)
> >
> > However, I don't think overriding width should be needed for this case
> > and just returning -EINVAL should be fine regardless of port state.
> > AFAIK it's the driver responsibility to populate acceptable defaults for
> > such parameters. What driver(s) have this issue ? Shouldn't it be fixed
> > there rather than here ?
>
> I just noticed that you reference commit f1b65df5a232 ("IB/mlx5: Add
> support for active_width and active_speed in RoCE"). Before this patch
> applied, the mlx5_ib driver set default active_width and active_speed to
> IB_WIDTH_4X and IB_SPEED_QDR.
>
> Should the fix be to hw/mlx5/main.c:translate_eth_proto_oper which now has:
>
> switch (eth_proto_oper) {
> ...
> default:
> return -EINVAL;
> }
>
> return 0;
>
> and change default case to:
> *active_width = IB_WIDTH_1X;
>
> ?
I suggest to restore previous behavior before apply f1b65df5a232.
diff --git a/drivers/infiniband/hw/mlx5/main.c b/drivers/infiniband/hw/mlx5/main.c
index 033b6af90de9..0d73d2772d9b 100644
--- a/drivers/infiniband/hw/mlx5/main.c
+++ b/drivers/infiniband/hw/mlx5/main.c
@@ -388,6 +388,9 @@ static int mlx5_query_port_roce(struct ib_device *device, u8 port_num,
if (err)
goto out;
+ props->active_width = IB_WIDTH_4X;
+ props->active_speed = IB_SPEED_QDR;
+
translate_eth_proto_oper(eth_prot_oper, &props->active_speed,
&props->active_width);
--
To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
