From: Jan Sokolowski <jan.sokolowski@xxxxxxxxx>
Change serdes mode setting to use MISC_CONFIG_BITS in
VERIFY_CAP_LOCAL_LINK_WIDTH register. This method of
setting up serdes loopback is universally compatible
across all firmware versions.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@xxxxxxxxx>
Signed-off-by: Jan Sokolowski <jan.sokolowski@xxxxxxxxx>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@xxxxxxxxx>
---
drivers/infiniband/hw/hfi1/chip.c | 42 ++++++++++++-------------------------
drivers/infiniband/hw/hfi1/chip.h | 3 +++
2 files changed, 17 insertions(+), 28 deletions(-)
diff --git a/drivers/infiniband/hw/hfi1/chip.c b/drivers/infiniband/hw/hfi1/chip.c
index d2d72e0..a6d61c4 100644
--- a/drivers/infiniband/hw/hfi1/chip.c
+++ b/drivers/infiniband/hw/hfi1/chip.c
@@ -9190,25 +9190,6 @@ static int do_quick_linkup(struct hfi1_devdata *dd)
}
/*
- * Set the SerDes to internal loopback mode.
- * Returns 0 on success, -errno on error.
- */
-static int set_serdes_loopback_mode(struct hfi1_devdata *dd)
-{
- int ret;
-
- ret = set_physical_link_state(dd, PLS_INTERNAL_SERDES_LOOPBACK);
- if (ret == HCMD_SUCCESS)
- return 0;
- dd_dev_err(dd,
- "Set physical link state to SerDes Loopback failed with return %d\n",
- ret);
- if (ret >= 0)
- ret = -EINVAL;
- return ret;
-}
-
-/*
* Do all special steps to set up loopback.
*/
static int init_loopback(struct hfi1_devdata *dd)
@@ -9233,13 +9214,11 @@ static int init_loopback(struct hfi1_devdata *dd)
return 0;
}
- /* handle serdes loopback */
- if (loopback == LOOPBACK_SERDES) {
- /* internal serdes loopack needs quick linkup on RTL */
- if (dd->icode == ICODE_RTL_SILICON)
- quick_linkup = 1;
- return set_serdes_loopback_mode(dd);
- }
+ /*
+ * SerDes loopback init sequence is handled in set_local_link_attributes
+ */
+ if (loopback == LOOPBACK_SERDES)
+ return 0;
/* LCB loopback - handled at poll time */
if (loopback == LOOPBACK_LCB) {
@@ -9298,7 +9277,7 @@ static int set_local_link_attributes(struct hfi1_pportdata *ppd)
u8 tx_polarity_inversion;
u8 rx_polarity_inversion;
int ret;
-
+ u32 misc_bits = 0;
/* reset our fabric serdes to clear any lingering problems */
fabric_serdes_reset(dd);
@@ -9344,7 +9323,14 @@ static int set_local_link_attributes(struct hfi1_pportdata *ppd)
if (ret != HCMD_SUCCESS)
goto set_local_link_attributes_fail;
- ret = write_vc_local_link_width(dd, 0, 0,
+ /*
+ * SerDes loopback init sequence requires
+ * setting bit 0 of MISC_CONFIG_BITS
+ */
+ if (loopback == LOOPBACK_SERDES)
+ misc_bits |= 1 << LOOPBACK_SERDES_CONFIG_BIT_MASK_SHIFT;
+
+ ret = write_vc_local_link_width(dd, misc_bits, 0,
opa_to_vc_link_widths(
ppd->link_width_enabled));
if (ret != HCMD_SUCCESS)
diff --git a/drivers/infiniband/hw/hfi1/chip.h b/drivers/infiniband/hw/hfi1/chip.h
index 213b6a3..fc122c1 100644
--- a/drivers/infiniband/hw/hfi1/chip.h
+++ b/drivers/infiniband/hw/hfi1/chip.h
@@ -583,6 +583,9 @@ enum {
#define LOOPBACK_LCB 2
#define LOOPBACK_CABLE 3 /* external cable */
+/* set up serdes bit in MISC_CONFIG_BITS */
+#define LOOPBACK_SERDES_CONFIG_BIT_MASK_SHIFT 0
+
/* read and write hardware registers */
u64 read_csr(const struct hfi1_devdata *dd, u32 offset);
void write_csr(const struct hfi1_devdata *dd, u32 offset, u64 value);
--
To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
