From: Jan Sokolowski <jan.sokolowski@xxxxxxxxx> Change QSFP cable error events logging levels from info to error. Reviewed-by: Jakub Byczkowski <jakub.byczkowski@xxxxxxxxx> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@xxxxxxxxx> Signed-off-by: Jan Sokolowski <jan.sokolowski@xxxxxxxxx> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@xxxxxxxxx> --- drivers/infiniband/hw/hfi1/chip.c | 64 +++++++++++++++++++------------------ 1 files changed, 32 insertions(+), 32 deletions(-) diff --git a/drivers/infiniband/hw/hfi1/chip.c b/drivers/infiniband/hw/hfi1/chip.c index a344dd8..358559c 100644 --- a/drivers/infiniband/hw/hfi1/chip.c +++ b/drivers/infiniband/hw/hfi1/chip.c @@ -9376,13 +9376,13 @@ static int handle_qsfp_error_conditions(struct hfi1_pportdata *ppd, if ((qsfp_interrupt_status[0] & QSFP_HIGH_TEMP_ALARM) || (qsfp_interrupt_status[0] & QSFP_HIGH_TEMP_WARNING)) - dd_dev_info(dd, "%s: QSFP cable temperature too high\n", - __func__); + dd_dev_err(dd, "%s: QSFP cable temperature too high\n", + __func__); if ((qsfp_interrupt_status[0] & QSFP_LOW_TEMP_ALARM) || (qsfp_interrupt_status[0] & QSFP_LOW_TEMP_WARNING)) - dd_dev_info(dd, "%s: QSFP cable temperature too low\n", - __func__); + dd_dev_err(dd, "%s: QSFP cable temperature too low\n", + __func__); /* * The remaining alarms/warnings don't matter if the link is down. @@ -9392,75 +9392,75 @@ static int handle_qsfp_error_conditions(struct hfi1_pportdata *ppd, if ((qsfp_interrupt_status[1] & QSFP_HIGH_VCC_ALARM) || (qsfp_interrupt_status[1] & QSFP_HIGH_VCC_WARNING)) - dd_dev_info(dd, "%s: QSFP supply voltage too high\n", - __func__); + dd_dev_err(dd, "%s: QSFP supply voltage too high\n", + __func__); if ((qsfp_interrupt_status[1] & QSFP_LOW_VCC_ALARM) || (qsfp_interrupt_status[1] & QSFP_LOW_VCC_WARNING)) - dd_dev_info(dd, "%s: QSFP supply voltage too low\n", - __func__); + dd_dev_err(dd, "%s: QSFP supply voltage too low\n", + __func__); /* Byte 2 is vendor specific */ if ((qsfp_interrupt_status[3] & QSFP_HIGH_POWER_ALARM) || (qsfp_interrupt_status[3] & QSFP_HIGH_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable RX channel 1/2 power too high\n", - __func__); + dd_dev_err(dd, "%s: Cable RX channel 1/2 power too high\n", + __func__); if ((qsfp_interrupt_status[3] & QSFP_LOW_POWER_ALARM) || (qsfp_interrupt_status[3] & QSFP_LOW_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable RX channel 1/2 power too low\n", - __func__); + dd_dev_err(dd, "%s: Cable RX channel 1/2 power too low\n", + __func__); if ((qsfp_interrupt_status[4] & QSFP_HIGH_POWER_ALARM) || (qsfp_interrupt_status[4] & QSFP_HIGH_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable RX channel 3/4 power too high\n", - __func__); + dd_dev_err(dd, "%s: Cable RX channel 3/4 power too high\n", + __func__); if ((qsfp_interrupt_status[4] & QSFP_LOW_POWER_ALARM) || (qsfp_interrupt_status[4] & QSFP_LOW_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable RX channel 3/4 power too low\n", - __func__); + dd_dev_err(dd, "%s: Cable RX channel 3/4 power too low\n", + __func__); if ((qsfp_interrupt_status[5] & QSFP_HIGH_BIAS_ALARM) || (qsfp_interrupt_status[5] & QSFP_HIGH_BIAS_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 1/2 bias too high\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 1/2 bias too high\n", + __func__); if ((qsfp_interrupt_status[5] & QSFP_LOW_BIAS_ALARM) || (qsfp_interrupt_status[5] & QSFP_LOW_BIAS_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 1/2 bias too low\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 1/2 bias too low\n", + __func__); if ((qsfp_interrupt_status[6] & QSFP_HIGH_BIAS_ALARM) || (qsfp_interrupt_status[6] & QSFP_HIGH_BIAS_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 3/4 bias too high\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 3/4 bias too high\n", + __func__); if ((qsfp_interrupt_status[6] & QSFP_LOW_BIAS_ALARM) || (qsfp_interrupt_status[6] & QSFP_LOW_BIAS_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 3/4 bias too low\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 3/4 bias too low\n", + __func__); if ((qsfp_interrupt_status[7] & QSFP_HIGH_POWER_ALARM) || (qsfp_interrupt_status[7] & QSFP_HIGH_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 1/2 power too high\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 1/2 power too high\n", + __func__); if ((qsfp_interrupt_status[7] & QSFP_LOW_POWER_ALARM) || (qsfp_interrupt_status[7] & QSFP_LOW_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 1/2 power too low\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 1/2 power too low\n", + __func__); if ((qsfp_interrupt_status[8] & QSFP_HIGH_POWER_ALARM) || (qsfp_interrupt_status[8] & QSFP_HIGH_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 3/4 power too high\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 3/4 power too high\n", + __func__); if ((qsfp_interrupt_status[8] & QSFP_LOW_POWER_ALARM) || (qsfp_interrupt_status[8] & QSFP_LOW_POWER_WARNING)) - dd_dev_info(dd, "%s: Cable TX channel 3/4 power too low\n", - __func__); + dd_dev_err(dd, "%s: Cable TX channel 3/4 power too low\n", + __func__); /* Bytes 9-10 and 11-12 are reserved */ /* Bytes 13-15 are vendor specific */ -- To unsubscribe from this list: send the line "unsubscribe linux-rdma" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
