Re: [PATCH v3 6/6] ARM: exynos: Add thermal sensor driver platform data support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue,  8 May 2012 21:48:18 +0530
Amit Daniel Kachhap <amit.kachhap@xxxxxxxxxx> wrote:

> This patch adds necessary default platform data support needed for TMU driver.
> This dt/non-dt values are tested for origen exynos4210 and smdk exynos5250 platforms.
> 
>
> ...
>
> --- a/drivers/thermal/exynos_thermal.c
> +++ b/drivers/thermal/exynos_thermal.c
> @@ -646,14 +646,117 @@ static irqreturn_t exynos_tmu_irq(int irq, void *id)
>  static struct thermal_sensor_conf exynos_sensor_conf = {
>  	.name			= "exynos-therm",
>  	.read_temperature	= (int (*)(void *))exynos_tmu_read,
> +};
> +
> +#if defined(CONFIG_CPU_EXYNOS4210)
> +static struct exynos_tmu_platform_data exynos4_default_tmu_data = {

Again, make it const if possible.

> +	.threshold = 80,
> +	.trigger_levels[0] = 5,
> +	.trigger_levels[1] = 20,
> +	.trigger_levels[2] = 30,
> +	.trigger_level0_en = 1,
> +	.trigger_level1_en = 1,
> +	.trigger_level2_en = 1,
> +	.trigger_level3_en = 0,
> +	.gain = 15,
> +	.reference_voltage = 7,
> +	.cal_type = TYPE_ONE_POINT_TRIMMING,
> +	.freq_tab[0] = {
> +		.freq_clip_max = 800 * 1000,
> +	},
> +	.freq_tab[1] = {
> +		.freq_clip_max = 200 * 1000,
> +	},
> +	.freq_tab_count = 2,
> +	.type = SOC_ARCH_EXYNOS4,
> +};
> +#define EXYNOS4_TMU_DRV_DATA ((kernel_ulong_t)&exynos4_default_tmu_data)
> +#else
> +#define EXYNOS4_TMU_DRV_DATA ((kernel_ulong_t)NULL)
> +#endif

See below.

> +#if defined(CONFIG_SOC_EXYNOS5250)
> +static struct exynos_tmu_platform_data exynos5_default_tmu_data = {
> +	.trigger_levels[0] = 85,
> +	.trigger_levels[1] = 103,
> +	.trigger_levels[2] = 110,
> +	.trigger_level0_en = 1,
> +	.trigger_level1_en = 1,
> +	.trigger_level2_en = 1,
> +	.trigger_level3_en = 0,
> +	.gain = 8,
> +	.reference_voltage = 16,
> +	.noise_cancel_mode = 4,
> +	.cal_type = TYPE_ONE_POINT_TRIMMING,
> +	.efuse_value = 55,
> +	.freq_tab[0] = {
> +		.freq_clip_max = 800 * 1000,
> +	},
> +	.freq_tab[1] = {
> +		.freq_clip_max = 200 * 1000,
> +	},
> +	.freq_tab_count = 2,
> +	.type = SOC_ARCH_EXYNOS5,
> +};
> +#define EXYNOS5_TMU_DRV_DATA ((kernel_ulong_t)&exynos5_default_tmu_data)

The use of kernel_ulong_t is unexpected.

I suspect you could remove this cast altogether.  Or make it void*.

> +#else
> +#define EXYNOS5_TMU_DRV_DATA ((kernel_ulong_t)NULL)

And remove this cast too.  Rely upon void* magic.

> +#endif
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id exynos_tmu_match[] = {
> +	{
> +		.compatible = "samsung,exynos4-tmu",
> +		.data = (void *)EXYNOS4_TMU_DRV_DATA,

No cast is needed if EXYNOS4_TMU_DRV_DATA has a pointer type.

> +	},
> +	{
> +		.compatible = "samsung,exynos5-tmu",
> +		.data = (void *)EXYNOS5_TMU_DRV_DATA,

No cast is needed if EXYNOS4_TMU_DRV_DATA has a pointer type.

> +	},
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, exynos_tmu_match);
> +#else
> +#define  exynos_tmu_match NULL
> +#endif
> +
>
> ...
>

_______________________________________________
linux-pm mailing list
linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linuxfoundation.org/mailman/listinfo/linux-pm


[Index of Archives]     [Linux ACPI]     [Netdev]     [Ethernet Bridging]     [Linux Wireless]     [CPU Freq]     [Kernel Newbies]     [Fedora Kernel]     [Security]     [Linux for Hams]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux RAID]     [Linux Admin]     [Samba]

  Powered by Linux