On Thu, 2012-04-12 at 15:11 -0400, Alan Stern wrote: > > # dmesg | grep target > > [ 8829.427534] atl1c 0000:04:00.0: target 3 wakeup 0 error 0 > > [ 8829.443524] xhci_hcd 0000:03:00.0: target 3 wakeup 1 error 0 > > [ 8829.459506] iwlwifi 0000:02:00.0: target 3 wakeup 0 error 0 > > [ 8829.459560] pci 0000:00:1f.3: target 0 wakeup 0 error 0 > > [ 8829.459607] pci 0000:00:1f.0: target 0 wakeup 0 error 0 > > [ 8829.475458] ehci_hcd 0000:00:1d.0: target 3 wakeup 1 error 0 > > [ 8829.491433] ehci_hcd 0000:00:1a.0: target 3 wakeup 1 error 0 > > [ 8829.507416] pci 0000:00:16.0: target 3 wakeup 0 error 0 > > The entries above are left over from the earlier test. Yep I knew that. I just figured to post the full dmesg grep instead of trimming it. ;-) > > > [ 9419.750158] atl1c 0000:04:00.0: target 3 wakeup 0 error 0 > > [ 9419.766134] pci 0000:03:00.0: target 3 wakeup 1 error 0 > > [ 9419.782126] iwlwifi 0000:02:00.0: target 3 wakeup 0 error 0 > > [ 9419.782181] pci 0000:00:1f.3: target 0 wakeup 0 error 0 > > [ 9419.782230] pci 0000:00:1f.0: target 0 wakeup 0 error 0 > > [ 9419.798087] pci 0000:00:1d.0: target 3 wakeup 1 error 0 > > [ 9419.814064] pci 0000:00:1a.0: target 3 wakeup 1 error 0 > > [ 9419.830031] pci 0000:00:16.0: target 3 wakeup 0 error 0 > > Evidently the script unbinds xhci-hcd too. Did you check to make > sure it is unrelated to the suspend problem? The script I found on the internet disables both. I just changed it to only disable ehci and did a full suspend, and it still works: [13538.700577] atl1c 0000:04:00.0: target 3 wakeup 0 error 0 [13538.716565] xhci_hcd 0000:03:00.0: target 3 wakeup 1 error 0 [13538.732542] iwlwifi 0000:02:00.0: target 3 wakeup 0 error 0 [13538.732596] pci 0000:00:1f.3: target 0 wakeup 0 error 0 [13538.732644] pci 0000:00:1f.0: target 0 wakeup 0 error 0 [13538.748503] pci 0000:00:1d.0: target 3 wakeup 1 error 0 [13538.764481] pci 0000:00:1a.0: target 3 wakeup 1 error 0 [13538.780448] pci 0000:00:16.0: target 3 wakeup 0 error 0 > > Anyway, this shows that the EHCI controllers are being set to the same > power state with the same wakeup settings in both cases. And yet one > hangs the computer while the other doesn't. > > Here's another rather drastic test you can do. In > drivers/usb/host/ehci-pci.c:ehci_pci_suspend(), call ehci_reset(ehci) > just before the final return statement. That should leave the hardware > in exactly the same state as if ehci-hcd had been unbound. Want me to remove previous updates before doing so? I can keep the dev_log, but what about the other change you asked about. -- Steve _______________________________________________ linux-pm mailing list linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx https://lists.linuxfoundation.org/mailman/listinfo/linux-pm
