On Tuesday, May 17, 2011, Dwight Schauer wrote:
> On Tue, May 17, 2011 at 3:03 PM, Rafael J. Wysocki <rjw@xxxxxxx> wrote:
> > On Tuesday, May 17, 2011, Rafael J. Wysocki wrote:
> >> On Tuesday, May 17, 2011, Dwight Schauer wrote:
> >> > >> > >> >> >> >> On Thursday, May 12, 2011, Alan Stern wrote:
> >> > >> >
> >> > >> > >> >> >> >> > For new readers: The problem is that an xHCI USB host controller does
> >> > >> > >> >> >> >> > not wake up a suspended system properly.
> >> > >> > ...
> >> > >> > >> > So, clearly, you don't get any PCIe PME interrupts from root ports
> >> > >> > >> > when the keyboard is plugged in. Without those interrupts the runtime
> >> > >> > >> > resume of xhci won't work.
> >> > >> > >> >
> >> > >> > >> > Please attach the output of "lspci -vv" with "auto" in the (suspended) xhci's
> >> > >> > >> > power/control file before and after you've plugged in the keyboard.
> >> > >> > >> >
> >> > >> > >> > Thanks,
> >> > >> > >> > Rafael
> >> > >> > >>
> >> > >> > >> The lspci -vv before, after, and diff are attached.
> >> > >> > >
> >> > >> > > This means that the PME signaled by the xHCI doesn't cause the PMEStatus bit
> >> > >> > > in its root port to be set, which is why the root port doesn't generate
> >> > >> > > interrupts. This seriously looks like a hardware bug and the only thing
> >> > >> > > we could do to work around it would be to poll the xHCI for the PME status
> >> > >> > > periodically (while suspended).
> >> > >> > >
> >> > >> > > Can you see if the feature works after booting with pcie_ports=compat in
> >> > >> > > the kernel command line?
> >> > >> > >
> >> > >> > > Rafael
> >> > >> > >
> >> > >> >
> >> > >> > I'll try that on Monday (the pcie_ports=compat kernel option).
> >> > >> >
> >> > >> > Well, I've got 2 different systems (one Intel and one AMD based, both
> >> > >> > exhibit the same behavior).
> >> > >>
> >> > >> Are both xHCI controllers from NEC?
> >> > >>
> >> > >> > I have a few other systems I can try it on as well on Monday.
> >> > >>
> >> > >> Please do if possible.
> >> > >
> >> > > If pcie_ports=compat doesn't help, does it help if you use pci=nomsi?
> >> > > I'm wondering if the hardware bug shows up only when MSI or MSI-X is
> >> > > enabled for the NEC hardware. Also, if you turn on
> >> > > CONFIG_USB_XHCI_HCD_DEBUGGING, what NEC firmware version do you see in
> >> > > dmesg?
> >> > >
> >> > > Sarah Sharp
> >> > >
> >> >
> >> > pcie_ports=compat had no effect
> >> > with pci_=nomsi I get upon boot.
> >> >
> >> > xhci_hcd 0000:02:00.0: Failed to enable MSI-X
> >> > xhci_hcd 0000:02:00.0: failed to allocate MSI entry
> >> > xhci_hcd 0000:06:00.0: Failed to enable MSI-X
> >> > xhci_hcd 0000:06:00.0: failed to allocate MSI entry
> >> >
> >> > The 6:00.0 is for NEC device in the PCIe slot.
> >> >
> >> > With pci_=nomsi the rutime power management works, I can put auto in
> >> > power/control and the device comes back on it's own.
> >> >
> >> > However, this does not address the wakeup from system suspend issue,
> >> > enabled in power/wakeup still does not work. If the interrupt is now
> >> > being polled, that would make sense as to why it still does not work.
> >> >
> >> > For TI's xHCI device I get "xhci_hcd 0000:02:00.0: failed to allocate
> >> > MSI entry" with pci=nomsi.
> >> >
> >> > The system with TI's device in it is exhibiting the same symptoms
> >> > (wakeup does not work and by default auto in power/control does not
> >> > work). It is a different motherboard and chip-set than the system I
> >> > have the NEC device in.
> >> >
> >> > pci=nomsi has no effect on the system with the TI xHCI device in it.
> >> > pcie_ports=compat had no effect either as far as making auto in
> >> > power/control work properly.
> >> >
> >> >
> >> > As to the NEC firmware, both the on-board and off-board NEC devices
> >> > have the same version:
> >> >
> >> > xhci_hcd 0000:02:00.0: NEC firmware version 30.21
> >> > xhci_hcd 0000:06:00.0: NEC firmware version 30.21
> >> >
> >> > Attached are the dmesg boot logs for both systems.
> >>
> >> OK, so for the S3 issue, I think there's a problem with the PCIe link
> >> on these devices such that the link is not present during resume
> >> and that's why commands are not reaching the device. I'm not sure yet
> >> what to do about it, but I wonder if xhci_hcd does something around
> >> PCIe links on suspend?
> >
> > It doesn't seem so.
> >
> > Dwight, can you comment out the pci_disable_device(pci_dev); in
> > drivers/usb/core/hcd-pci.c and see if that makes a difference?
> >
> > Rafael
>
> I just tried that, but it has no effect on wakeup from S3.
OK, one more test, please.
Try to do
# echo core > /sys/power/pm_test
# echo mem > /sys/power/state
(that should simulate suspend, but without going into the BIOS, and it
should return do the command prompt after 5-10 sec.) and check if the
USB3 controllers work after that ("echo none > /sys/power/pm_test" resets
to the normal suspend behavior).
Thanks,
Rafael
_______________________________________________
linux-pm mailing list
linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linux-foundation.org/mailman/listinfo/linux-pm
