On Dec 17 Stefan Richter wrote: > On Dec 11 Alan Stern wrote: > > This is probably because hal probes the DVD drive every two seconds > > looking for media changes. However that's not supposed to cause > > rpm_resume to be called for the host unless runtime PM is allowed for > > the DVD drive, which it isn't according to your listings below. So > > there's a bug somewhere. > > I had 2.6.36 running since then and have now booted into 2.6.37-rc6. > > Yes, it is hal indeed. Shutting hal down avoids this logging activity. [...] > Actually, this time I see once every two seconds a message about > logical unit 6:0:0:0 and 6 times every two seconds a message about > host7: > > Dec 17 20:22:08 stein kernel: sd 6:0:0:0: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: sd 6:0:0:0: rpm_resume returns 1 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:08 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: sd 6:0:0:0: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: sd 6:0:0:0: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume flags 0x4 > Dec 17 20:22:10 stein kernel: scsi host7: rpm_resume returns 1 > > sd 6:0:0:0 is a USB card reader built into a monitor: > Host: scsi6 Channel: 00 Id: 00 Lun: 00 > Vendor: Generic Model: Ultra HS-SD/MMC Rev: 1.88 > Type: Direct-Access ANSI SCSI revision: 00 Well right --- hald polls the card reader for media change too. I now noticed that the two lines sd *:0:0:0: rpm_resume flags 0x4 sd *:0:0:0: rpm_resume returns 1 are logged once for each sd device (i.e. those with fixed media too) at the startup of hald. Is this expected? Note, I have not seen anything of the sort on another PC which runs 2.3.37-rc6 with the same PM debug options. The differences are that the other PC is an Intel 945GM based one with x86-32 kernel and 32bit Gentoo userland, whereas the PC with log spam is an AMD RS780 based one with x86-64 kernel and 64bit Gentoo userland. Both got hal 0.5.14-r2. -- Stefan Richter -=====-==-=- ==-- =---= http://arcgraph.de/sr/ _______________________________________________ linux-pm mailing list linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx https://lists.linux-foundation.org/mailman/listinfo/linux-pm
