On Tue, 15 Dec 2009, Alan Stern wrote: > > It doesn't feel like an ugly hack to me. It seems like exactly the > Right Thing To Do: Make as many devices as possible use async > suspend/resume. The reason it's a ugly hack is that it's actually not a simple decision to make. The devil is in the details: > The only reason we don't make every device async is because we don't > know whether it's safe. In the case of PCI bridges we _do_ know -- > because they don't have any work to do outside of > late_suspend/early_resume -- and so they _should_ be async. That's the theory, yes. And it was worth the comment to spell out that theory. But.. It's a very subtle theory, and it's not necessarily always 100% true. For example, a cardbus bridge is strictly speaking very much a PCI bridge, but for cardbus bridges we _do_ have a suspend/resume function. And perhaps worse than that, cardbus bridges are one of the canonical examples where two different PCI devices actually share registers. It's quite common that some of the control registers are shared across the two subfunctions of a two-slot cardbus controller (and we generally don't even have full docs for them!) > The same goes for devices that don't have suspend or resume methods. Yes and no. Again, the "async_suspend" flag is done at the generic device layer, but 99% of all suspend/resume methods are _not_ done at that level: they are bus-specific functions, where the bus has a generic suspend-resume function that it exposes to the generic device layer, and that knows about the bus-specific rules. So if you are a PCI device (to take just that example - but it's true of just about all other buses too), and you don't have any suspend or resume methods, it's actually impossible to see that fact from the generic device layer. And even when you know it's PCI, our rules are actually not simple at all. Our rules for PCI devices (and this strictly speaking is true for bridges too) are rather complex: - do we have _any_ legacy PM support (ie the "direct" driver suspend/resume functions in the driver ops, rather than having a "struct dev_pm_ops" pointer)? If so, call "->suspend()" - If not - do we have that "dev_pm_ops" thing? If so, call it. - If not - just disable the device entirely _UNLESS_ you're a PCI bridge. Notice? The way things are set up, if you have no suspend routine, you'll not get suspended, but you will get disabled. So it's _not_ actually safe to asynchronously suspend a PCI device if that device has no driver or no suspend routines - because even in the absense of a driver and suspend routines, we'll still least disable it. And if there is some subtle dependency on that device that isn't obvious (say, it might be used indirectly for some ACPI thing), then that async suspend is the wrong thing to do. Subtle? Hell yes. So the whole thing about "we can do PCI bridges asynchronously because they are obviously no-op" is kind of true - except for the "obviously" part. It's not obvious at all. It's rather subtle. As an example of this kind of subtlety - iirc PCIE bridges used to have suspend and resume bugs when we initially switched over to the "new world" suspend/resume exactly because they actually did things at "suspend" time (rather than suspend_late), and that broke devices behind them (this was not related to async, of course, but the point is that even when you look like a PCI bridge, you might be doing odd things). So just saying "let's do it asynchronously" is _not_ always guaranteed to be the right thing at all. It's _probably_ safe for at least regular PCI bridges. Cardbus bridges? Probably not, but since most modern laptop have just a single slot - and people who have multiple slots seldom use them all - most people will probably never see the problems that it _could_ introduce. And PCIE bridges? Should be safe these days, but it wasn't quite as obvious, because a PCIE bridge actually has a driver unlike a regular plain PCI-PCI bridge. Subtle, subtle. > There remains a separate question: Should async devices also be forced > to wait for their children? I don't see why not. For PCI bridges it > won't make any significant difference. As long as the async code > doesn't have to do anything, who cares when it runs? That's why I just set the "async_resume = 1" thing. But there might actually be reasons why we care. Like the fact that we actually throttle the amount of parallel work we do in async_schedule(). So doing even a "no-op" asynchronously isn't actually a no-op: while it is pending (and those things can be pending for a long time, since they have to wait for those slow devices underneath them), it can cause _other_ async work - that isn't necessarily a no-op at all - to be then done synchronously. Now, admittedly our async throttling limits are high enough that the above kind of detail will probably never ever realy matter (default 256 worker threads etc). But it's an example of how practice is different from theory - in _theory_ it doesn't make any difference if you wait for something asynchronously, but in practice it could make a difference under some circumstances. Linus _______________________________________________ linux-pm mailing list linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx https://lists.linux-foundation.org/mailman/listinfo/linux-pm
