Re: [RFC PATCH 2/3] PCI: parallel resume for pci devices on bus 0

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 2008-12-22 at 23:52 +0800, Alan Stern wrote:
> On Mon, 22 Dec 2008, Zhang Rui wrote:
> 
> > On Fri, 2008-12-19 at 23:09 +0800, Alan Stern wrote:
> > > On Fri, 19 Dec 2008, Zhang Rui wrote:
> > > 
> > > > device parallel resume support for PCI devices
> > > 
> > > There are some PCI devices which won't work right if they are resumed
> > > in parallel.  The example I have in mind is a USB host controller
> > > device with both a high-speed EHCI controller function and some
> > > companion low/full-speed UHCI or OHCI controller functions.  The EHCI
> > > driver relies on the fact that the EHCI controller has a higher
> > > function number and therefore is resumed _after_ the companion
> > > controllers.
> > > 
> > well, I never got this problem before.
> > is this normal? does this exist on the Intel hardware?
> > I'd like to do some test if I have chance.
> 
> Yes, it is normal, and it does exist on Intel hardware.  It isn't a 
> _problem_ (or at least, it hasn't been a problem up until now) because 
> the order of resuming devices is always the same as the order of 
> registration, which in turn is the same as the order of discovery.
> 
> You can see this on any Intel ICHx chipset.  I don't have an example 
> right here, but take a look at the machines you have lying around.  
> There are PCI UHCI controllers at 1d.0, 1d.1, ... and a PCI EHCI 
> controller at 1d.7.
> 
> The issue arises when you have a low-speed or full-speed device plugged 
> in.  The device is handed over from the EHCI controller to one of the 
> companion UHCI controllers, because EHCI manages only high-speed 
> devices.
> 
> Now consider what happens when the system wakes up from hibernation.  
> The controllers are re-initialized, and when ehci-hcd sees the
> low/full-speed device, it tries to hand the device over to the
> companion controller again.  But if the EHCI controller's resume method
> runs first then the handover will fail, because the companion
> controller has not yet been initialized.  As a result, the device will
> be lost and will have to go through rediscovery and re-enumeration.  
> This could be very annoying if, for example, the device contains a
> mounted filesystem.
> 
> > Just like the case above, can you give me a lspci output and show me
> > what exactly the dependency is?
> 
> The dependency is simple: The 1d.7 device must be resumed _after_ 1d.0, 
> 1d.1, ..., 1d.6.
Then I have a question, what if the uchi_hcd is not loaded?
the ehci host controller doesn't work in this case?

thanks,
rui

_______________________________________________
linux-pm mailing list
linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linux-foundation.org/mailman/listinfo/linux-pm

[Index of Archives]     [Linux ACPI]     [Netdev]     [Ethernet Bridging]     [Linux Wireless]     [CPU Freq]     [Kernel Newbies]     [Fedora Kernel]     [Security]     [Linux for Hams]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux RAID]     [Linux Admin]     [Samba]

  Powered by Linux