Alan Stern wrote:> On Sun, 1 Jun 2008, Tobias Diedrich wrote:> > > Ok, after another long debugging session I finally found out the> > reason for the immediate reboot (after finding the place that> > suspends the serial console (drivers/pnp) and disabling that suspend> > path):> > The system is woken up by USB activity! (Optical mouse, anyone?)> > > > Lo and behold:> > drivers/usb/core/hcd-pci.c tries it's best to activate 'wake on> > usb', which I didn't know since it apparently also never worked.> > However, after applying the 'use platform_enable_wakeup'-patch,> > not only forcedeth wake starts working, also usb wake.> > If I prevent usb wake:> > |echo disabled > /sys/devices/pci0000\:00/0000\:00\:02.0/power/wakeup'> > |echo disabled > /sys/devices/pci0000\:00/0000\:00\:02.1/power/wakeup'> > And then hibernate in platform mode, the immediate reboot is gone> > and waking up using magic packets works fine even without setting up> > /proc/acpi/wakeup first.> > > > Maybe I should try hooking mouse and keyboard onto different usb> > host controllers, so I can disable wakeup for the mouse host> > controller and enable wakeup for the keyboard host controller,> > then it should be possible to wake the system by pressing a key. :)> > You don't need to do that. Wakeup can be set specifically for each > individual USB device, provided CONFIG_USB_SUSPEND is enabled.
Cool, I didn't know that. :)
> On Sun, 1 Jun 2008, Tobias Diedrich wrote:> > > (BTW I first thought the 'immediate reboot because of usb wake' effect is> > caused by the optical mouse generating a wake event, but it rather> > seems to be a problem with a flaky secondary usb host controller,> > which sees a connected device where nothing is attached)> > Can you provide debugging information (i.e., CONFIG_USB_DEBUG) with the > details on this bogus wakeup?
Sure.Here is the complete log of one boot and two s2disk_platform cyclescaptured using the serial console (in the first s2disk I forgot toremove the 'turn off /sys/bus/usb/device/usb?/power/wakeup' part).
Interestingly even with power/wakeup disabled for usb1 and usb2,which I assume to be the usb root ports, I could wake up the systemby pressing a key on my keyboard (which didn't work before turningon CONFIG_USB_SUSPEND).
On the second suspend the system rebooted immediately as expected(I power/wakeup for usb1 and usb2 back on and disabled the part inthe script).
I think this might be some general usb hw flakiness, since it seemsto detect (and has so for a long time) a non-existing device:
lsusb output:Bus 002 Device 003: ID 045e:00db Microsoft Corp. Natural Ergonomic Keyboard 4000 V1.0Bus 002 Device 002: ID 045e:0040 Microsoft Corp. Wheel Mouse OpticalBus 002 Device 001: ID 1d6b:0001 Bus 001 Device 001: ID 1d6b:0002
bogus device?:[14316046.469949] usb 2-4: new full speed USB device using ohci_hcd and address 12[14316046.679951] usb 2-4: device descriptor read/64, error -62[14316046.986619] usb 2-4: device descriptor read/64, error -62[14316047.263284] usb 2-4: new full speed USB device using ohci_hcd and address 13[14316047.476614] usb 2-4: device descriptor read/64, error -62[14316047.786618] usb 2-4: device descriptor read/64, error -62[14316048.063282] usb 2-4: new full speed USB device using ohci_hcd and address 14[14316048.499945] usb 2-4: device not accepting address 14, error -62[14316048.669950] usb 2-4: new full speed USB device using ohci_hcd and address 15[14316049.106612] usb 2-4: device not accepting address 15, error -62[14316049.112960] hub 2-0:1.0: unable to enumerate USB device on port 4
complete log:[ 0.000000] Linux version 2.6.26-rc4 (ranma@melchior) (gcc version 4.2.3 (Debian 4.2.3-5)) #28 PREEMPT Sun Jun 1 09:06:24 CEST 2008[ 0.000000] Command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose console=ttyS0,115200 console=tty0 pci=nomsi no_console_suspend ro[ 0.000000] BIOS-provided physical RAM map:[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)[ 0.000000] BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)[ 0.000000] max_pfn_mapped = 1048576[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[ 0.000000] init_memory_mapping[ 0.000000] DMI 2.4 present.[ 0.000000] ACPI: RSDP 000F7D20, 0024 (r2 Nvidia)[ 0.000000] ACPI: XSDT 7FEE3100, 004C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: FACP 7FEEADC0, 00F4 (r3 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: DSDT 7FEE3280, 7ACE (r1 NVIDIA AWRDACPI 1000 MSFT 3000000)[ 0.000000] ACPI: FACS 7FEE0000, 0040[ 0.000000] ACPI: SSDT 7FEEB000, 0136 (r1 PTLTD POWERNOW 1 LTP 1)[ 0.000000] ACPI: HPET 7FEEB180, 0038 (r1 Nvidia ASUSACPI 42302E31 AWRD 98)[ 0.000000] ACPI: MCFG 7FEEB200, 003C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: APIC 7FEEAF00, 0098 (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] early res: 0 [0-fff] BIOS data page[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE[ 0.000000] early res: 2 [200000-d3638f] TEXT DATA BSS[ 0.000000] early res: 3 [9f800-fffff] BIOS reserved[ 0.000000] early res: 4 [8000-bfff] PGTABLE[ 0.000000] Zone PFN ranges:[ 0.000000] DMA 0 -> 4096[ 0.000000] DMA32 4096 -> 1048576[ 0.000000] Normal 1048576 -> 1048576[ 0.000000] Movable zone start PFN for each node[ 0.000000] early_node_map[2] active PFN ranges[ 0.000000] 0: 0 -> 159[ 0.000000] 0: 256 -> 524000[ 0.000000] Detected use of extended apic ids on hypertransport bus[ 0.000000] ACPI: PM-Timer IO Port: 0x1008[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)[ 0.000000] Setting APIC routing to flat[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000[ 0.000000] Using ACPI (MADT) for SMP configuration information[ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000)[ 0.000000] mapped IOAPIC to ffffffffff5fa000 (00000000fec00000)[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)[14315324.233334] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 513763[14315324.233334] Kernel command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose console=ttyS0,115200 console=tty0 pci=nomsi no_console_suspend ro[14315324.233334] Initializing CPU#0[14315324.233334] PID hash table entries: 4096 (order: 12, 32768 bytes)[14315324.233334] Extended CMOS year: 2000[14315324.233334] TSC calibrated against PM_TIMER[14315324.233334] time.c: Detected 2411.107 MHz processor.[14315324.233334] Console: colour VGA+ 80x60[14315324.233334] console [tty0] enabled[14315324.233334] console [ttyS0] enabled[14315324.233334] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar[14315324.233334] ... MAX_LOCKDEP_SUBCLASSES: 8[14315324.233334] ... MAX_LOCK_DEPTH: 48[14315324.233334] ... MAX_LOCKDEP_KEYS: 2048[14315324.233334] ... CLASSHASH_SIZE: 1024[14315324.233334] ... MAX_LOCKDEP_ENTRIES: 8192[14315324.233334] ... MAX_LOCKDEP_CHAINS: 16384[14315324.233334] ... CHAINHASH_SIZE: 8192[14315324.233334] memory used by lock dependency info: 1648 kB[14315324.233334] per task-struct memory footprint: 2688 bytes[14315324.233334] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)[14315324.233334] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)[14315324.233334] Checking aperture...[14315324.233334] Node 0: aperture @ ab94000000 size 32 MB[14315324.233334] Aperture beyond 4GB. Ignoring.[14315324.233334] No AGP bridge found[14315324.233334] Memory: 2051692k/2096000k available (4624k kernel code, 43544k reserved, 2268k data, 260k init)[14315324.316528] Calibrating delay using timer specific routine.. 4827.00 BogoMIPS (lpj=8043211)[14315324.322857] Mount-cache hash table entries: 256[14315324.327217] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)[14315324.333327] CPU: L2 Cache: 512K (64 bytes/line)[14315324.336660] CPU: AMD Athlon(tm) 64 Processor 3800+ stepping 01[14315324.342947] ACPI: Core revision 20080321[14315324.359992] Parsing all Control Methods:[14315324.364011] Table [DSDT](id 0001) - 1203 Objects with 101 Devices 380 Methods 44 Regions[14315324.369992] Parsing all Control Methods:[14315324.373967] Table [SSDT](id 0002) - 4 Objects with 0 Devices 0 Methods 0 Regions[14315324.379991] tbxface-0598 [02] tb_load_namespace : ACPI Tables successfully acquired[14315324.389990] evxfevnt-0091 [02] enable : Transition to ACPI mode successful[14315324.398904] enabled ExtINT on CPU#0[14315324.402998] ENABLING IO-APIC IRQs[14315324.406656] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1[14315324.442963] Using local APIC timer interrupts.[14315324.449986] Detected 12.557 MHz APIC timer.[14315324.453320] net_namespace: 1272 bytes[14315324.456653] NET: Registered protocol family 16[14315324.460262] No dock devices found.[14315324.464194] TOM: 0000000080000000 aka 2048M[14315324.468795] ACPI: bus type pci registered[14315324.473293] PCI: Using configuration type 1 for base access[14315324.481636] evgpeblk-0956 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9[14315324.490696] evgpeblk-0956 [04] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9[14315324.509805] Completing Region/Field/Buffer/Package initialization:...................................................................................................................................................................................[14315324.545447] Initialized 39/44 Regions 11/11 Fields 40/40 Buffers 89/101 Packages (1216 nodes)[14315324.549980] Initializing Device/Processor/Thermal objects by executing _INI methods:...[14315324.556256] Executed 3 _INI methods requiring 1 _STA executions (examined 108 objects)[14315324.559979] evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 0 Runtime GPEs in this block[14315324.569979] evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 1 Runtime GPEs in this block[14315324.579978] ACPI: Interpreter enabled[14315324.583311] ACPI: (supports S0 S1 S3 S4 S5)[14315324.587948] ACPI: Using IOAPIC for interrupt routing[14315324.615454] ACPI: PCI Root Bridge [PCI0] (0000:00)[14315324.619975] PCI: Transparent bridge - 0000:00:06.0[14315324.713931] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.722733] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.728224] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 *10 11 14 15)[14315324.735722] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.741551] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.750168] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.758958] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)[14315324.763301] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.768608] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.777265] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)[14315324.784758] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)[14315324.792250] ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)[14315324.796634] ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)[14315324.800688] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.809482] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)[14315324.813827] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)[14315324.821294] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.829954] ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)[14315324.834333] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)[14315324.841605] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)[14315324.849225] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.[14315324.853301] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.[14315324.857246] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0[14315324.863511] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.[14315324.870581] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.[14315324.877827] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.[14315324.885078] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0[14315324.889968] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.[14315324.895427] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0[14315324.899968] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0[14315324.903301] ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0[14315324.907248] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.[14315324.915379] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0[14315324.919968] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0[14315324.923301] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0[14315324.927247] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.[14315324.934990] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.[14315324.943235] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0[14315324.947245] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0[14315324.954299] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0[14315324.961445] Linux Plug and Play Support v0.97 (c) Adam Belay[14315324.966635] pnp: PnP ACPI init[14315324.969968] ACPI: bus type pnp registered[14315324.982451] pnp: PnP ACPI: found 13 devices[14315324.986635] ACPI: ACPI bus type pnp unregistered[14315324.989968] SCSI subsystem initialized[14315324.993377] usbcore: registered new interface driver usbfs[14315324.999287] usbcore: registered new interface driver hub[14315325.003301] usbcore: registered new device driver usb[14315325.006635] PCI: Using ACPI for IRQ routing[14315325.009968] testing the IO APIC.......................[14315325.013301] [14315325.013301] .................................... done.[14315325.027785] Bluetooth: Core ver 2.11[14315325.031917] NET: Registered protocol family 31[14315325.036635] Bluetooth: HCI device and connection manager initialized[14315325.039968] Bluetooth: HCI socket layer initialized[14315325.043301] DMAR:parse DMAR table failure.[14315325.054043] system 00:01: ioport range 0x1000-0x107f has been reserved[14315325.060940] system 00:01: ioport range 0x1080-0x10ff has been reserved[14315325.067827] system 00:01: ioport range 0x1400-0x147f has been reserved[14315325.074713] system 00:01: ioport range 0x1480-0x14ff has been reserved[14315325.081599] system 00:01: ioport range 0x1800-0x187f has been reserved[14315325.088485] system 00:01: ioport range 0x1880-0x18ff has been reserved[14315325.095383] system 00:02: ioport range 0x4d0-0x4d1 has been reserved[14315325.102096] system 00:02: ioport range 0x800-0x87f has been reserved[14315325.108810] system 00:02: ioport range 0x290-0x297 has been reserved[14315325.115545] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved[14315325.123493] system 00:0c: iomem range 0xcd000-0xcffff has been reserved[14315325.130468] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved[14315325.139923] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved[14315325.147331] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved[14315325.154737] system 00:0c: iomem range 0xfefff000-0xfefff0ff could not be reserved[14315325.162662] system 00:0c: iomem range 0x7fee0000-0x7fefffff could not be reserved[14315325.170117] system 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved[14315325.178042] system 00:0c: iomem range 0x0-0x9ffff could not be reserved[14315325.185014] system 00:0c: iomem range 0x100000-0x7fedffff could not be reserved[14315325.199644] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved[14315325.206697] system 00:0c: iomem range 0xfee00000-0xfeefffff could not be reserved[14315325.214622] system 00:0c: iomem range 0xfefff000-0xfeffffff could not be reserved[14315325.222574] system 00:0c: iomem range 0xfff80000-0xfff80fff could not be reserved[14315325.230499] system 00:0c: iomem range 0xfff90000-0xfffbffff could not be reserved[14315325.238429] system 00:0c: iomem range 0xfffed000-0xfffeffff could not be reserved[14315325.247393] PCI: Bridge: 0000:00:06.0[14315325.251010] IO window: 9000-9fff[14315325.254789] MEM window: disabled.[14315325.259839] PREFETCH window: disabled.[14315325.263706] PCI: Bridge: 0000:00:0a.0[14315325.267734] IO window: 8000-8fff[14315325.271508] MEM window: 0xfde00000-0xfdefffff[14315325.276406] PREFETCH window: 0x00000000e8000000-0x00000000efffffff[14315325.283120] PCI: Bridge: 0000:00:0e.0[14315325.287151] IO window: 6000-7fff[14315325.290924] MEM window: 0xfdd00000-0xfddfffff[14315325.295819] PREFETCH window: disabled.[14315325.300188] NET: Registered protocol family 2[14315325.336002] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)[14315325.344144] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)[14315325.353336] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)[14315325.365879] TCP: Hash tables configured (established 262144 bind 65536)[14315325.372885] TCP reno registered[14315325.385861] NET: Registered protocol family 1[14315325.392316] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).[14315325.399451] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.[14315325.405975] fuse init (API version 7.9)[14315325.410333] SGI XFS with security attributes, large block/inode numbers, no debug enabled[14315325.419250] msgmni has been set to 4007 for ipc namespace ffffffff808882f0[14315325.426690] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)[14315325.434542] io scheduler noop registered[14315325.439746] io scheduler anticipatory registered[14315325.444057] io scheduler deadline registered[14315325.449069] io scheduler cfq registered (default)[14315325.466317] pci 0000:00:05.0: Enabling HT MSI Mapping[14315325.471768] pci 0000:00:05.1: Enabling HT MSI Mapping[14315325.476878] pci 0000:00:05.2: Enabling HT MSI Mapping[14315325.482326] pci 0000:00:06.0: Enabling HT MSI Mapping[14315325.487762] pci 0000:00:06.1: Enabling HT MSI Mapping[14315325.493216] pci 0000:00:08.0: Enabling HT MSI Mapping[14315325.498657] pci 0000:00:09.0: Enabling HT MSI Mapping[14315325.504089] pci 0000:00:0a.0: Enabling HT MSI Mapping[14315325.509542] pci 0000:00:0e.0: Enabling HT MSI Mapping[14315325.515240] assign_interrupt_mode Found MSI capability[14315325.520563] assign_interrupt_mode Found MSI capability[14315325.526830] input: Power Button (FF) as /class/input/input0[14315325.532803] ACPI: Power Button (FF) [PWRF][14315325.537393] input: Power Button (CM) as /class/input/input1[14315325.543334] ACPI: Power Button (CM) [PWRB][14315325.549405] ACPI: PNP0C0B:00 is registered as cooling_device0[14315325.556669] ACPI: Fan [FAN] (on)[14315325.560283] ACPI: ACPI0007:00 is registered as cooling_device1[14315325.566782] ACPI: Expecting a [Reference] package element, found type 0[14315325.574062] ACPI: LNXTHERM:01 is registered as thermal_zone0[14315325.580526] ACPI: Thermal Zone [THRM] (40 C)[14315325.603598] Real Time Clock Driver v1.12ac[14315325.608082] Linux agpgart interface v0.103[14315325.612554] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled[14315325.622766] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A[14315325.630112] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A[14315325.637619] loop: module loaded[14315325.641039] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2[14315325.647521] e1000e: Copyright (c) 1999-2008 Intel Corporation.[14315325.653835] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI[14315325.660291] e100: Copyright(c) 1999-2006 Intel Corporation[14315325.666298] tun: Universal TUN/TAP device driver, 1.6[14315325.671719] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>[14315325.678486] Driver 'sd' needs updating - please use bus_type methods[14315325.685250] Driver 'sr' needs updating - please use bus_type methods[14315325.692968] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23[14315325.699090] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14315325.708856] sata_nv 0000:00:05.0: Using SWNCQ mode[14315325.714155] scsi0 : sata_nv[14315325.717573] scsi1 : sata_nv[14315325.721157] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 23[14315325.729249] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 23[14315326.206695] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14315326.220214] ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7[14315326.226591] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)[14315326.240528] ata1.00: configured for UDMA/133[14315326.573689] ata2: SATA link down (SStatus 0 SControl 300)[14315326.592884] isa bounce pool size: 16 pages[14315326.596954] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5[14315326.606003] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315326.613427] sd 0:0:0:0: [sda] Write Protect is off[14315326.618629] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315326.627076] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315326.636278] sd 0:0:0:0: [sda] Write Protect is off[14315326.640932] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315326.650430] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >[14315326.691809] sd 0:0:0:0: [sda] Attached SCSI disk[14315326.697309] sd 0:0:0:0: Attached scsi generic sg0 type 0[14315326.706671] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22[14315326.712679] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14315326.720959] sata_nv 0000:00:05.1: Using SWNCQ mode[14315326.726665] scsi2 : sata_nv[14315326.730009] scsi3 : sata_nv[14315326.733588] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 22[14315326.740998] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 22[14315327.077024] ata3: SATA link down (SStatus 0 SControl 300)[14315327.423689] ata4: SATA link down (SStatus 0 SControl 300)[14315327.443336] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21[14315327.449341] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14315327.457739] sata_nv 0000:00:05.2: Using SWNCQ mode[14315327.463435] scsi4 : sata_nv[14315327.466797] scsi5 : sata_nv[14315327.470365] ata5: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb400 irq 21[14315327.477943] ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb800 bmdma 0xb408 irq 21[14315327.813749] ata5: SATA link down (SStatus 0 SControl 300)[14315328.303360] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14315328.316777] ata6.00: ATAPI: TSSTcorp CDDVDW SH-S203B, SB00, max UDMA/100[14315328.336778] ata6.00: configured for UDMA/100[14315328.355468] scsi 5:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S203B SB00 PQ: 0 ANSI: 5[14315328.366670] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray[14315328.373341] Uniform CD-ROM driver Revision: 3.20[14315328.380357] sr 5:0:0:0: Attached scsi generic sg1 type 5[14315328.391894] block2mtd: version $Revision: 1.30 $[14315328.397846] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20[14315328.403986] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14315328.413704] ehci_hcd 0000:00:02.1: EHCI Host Controller[14315328.420231] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1[14315328.427723] ehci_hcd 0000:00:02.1: debug port 1[14315328.433160] ehci_hcd 0000:00:02.1: irq 20, io mem 0xfe02e000[14315328.448349] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004[14315328.456845] usb usb1: configuration #1 chosen from 1 choice[14315328.462979] hub 1-0:1.0: USB hub found[14315328.467136] hub 1-0:1.0: 10 ports detected[14315328.573556] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002[14315328.580717] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1[14315328.588392] usb usb1: Product: EHCI Host Controller[14315328.595058] usb usb1: Manufacturer: Linux 2.6.26-rc4 ehci_hcd[14315328.600310] usb usb1: SerialNumber: 0000:00:02.1[14315328.607391] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23[14315328.613502] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14315328.622764] ohci_hcd 0000:00:02.0: OHCI Host Controller[14315328.628592] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2[14315328.636474] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000[14315328.695724] usb usb2: configuration #1 chosen from 1 choice[14315328.701789] hub 2-0:1.0: USB hub found[14315328.705943] hub 2-0:1.0: 10 ports detected[14315328.783404] hub 1-0:1.0: unable to enumerate USB device on port 1[14315328.816650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001[14315328.823342] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1[14315328.830616] usb usb2: Product: OHCI Host Controller[14315328.835858] usb usb2: Manufacturer: Linux 2.6.26-rc4 ohci_hcd[14315328.840212] usb usb2: SerialNumber: 0000:00:02.0[14315328.846458] USB Universal Host Controller Interface driver v3.0[14315328.986691] hub 1-0:1.0: unable to enumerate USB device on port 3[14315329.163356] hub 1-0:1.0: unable to enumerate USB device on port 4[14315329.169974] usbcore: registered new interface driver usblp[14315329.176790] PNP: No PS/2 controller found. Probing ports directly.[14315329.183811] serio: i8042 KBD port at 0x60,0x64 irq 1[14315329.189375] serio: i8042 AUX port at 0x60,0x64 irq 12[14315329.195449] mice: PS/2 mouse device common for all mice[14315329.219956] i2c /dev entries driver[14315329.223980] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00[14315329.230289] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40[14315329.236621] it87: Found IT8716F chip at 0x290, revision 0[14315329.240605] it87: in3 is VCC (+5V)[14315329.246525] it87: in7 is VCCH (+5V Stand-By)[14315329.276668] md: raid1 personality registered for level 1[14315329.283566] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx[14315329.292582] Bluetooth: HCI USB driver ver 2.9[14315329.450012] usb 2-1: new low speed USB device using ohci_hcd and address 2[14315329.636693] usb 2-1: configuration #1 chosen from 1 choice[14315329.660003] usb 2-1: New USB device found, idVendor=045e, idProduct=0040[14315329.666684] usb 2-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0[14315329.674262] usb 2-1: Product: Microsoft 3-Button Mouse with IntelliEye(TM)[14315329.683288] usb 2-1: Manufacturer: Microsoft[14315329.963344] usb 2-3: new low speed USB device using ohci_hcd and address 3[14315330.156679] usb 2-3: configuration #1 chosen from 1 choice[14315330.193336] usb 2-3: New USB device found, idVendor=045e, idProduct=00db[14315330.200017] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0[14315330.207602] usb 2-3: Product: Natural® Ergonomic Keyboard 4000[14315330.213796] usb 2-3: Manufacturer: Microsoft[14315330.496678] usb 2-4: new full speed USB device using ohci_hcd and address 4[14315330.670011] usb 2-4: device descriptor read/64, error -62[14315330.943344] usb 2-4: device descriptor read/64, error -62[14315331.210011] usb 2-4: new full speed USB device using ohci_hcd and address 5[14315331.383344] usb 2-4: device descriptor read/64, error -62[14315331.656677] usb 2-4: device descriptor read/64, error -62[14315331.923344] usb 2-4: new full speed USB device using ohci_hcd and address 6[14315332.336674] usb 2-4: device not accepting address 6, error -62[14315332.500011] usb 2-4: new full speed USB device using ohci_hcd and address 7[14315332.913341] usb 2-4: device not accepting address 7, error -62[14315332.919546] hub 2-0:1.0: unable to enumerate USB device on port 4[14315332.926358] usbcore: registered new interface driver hci_usb[14315332.932679] Bluetooth: HCI UART driver ver 2.2[14315332.938855] Bluetooth: HCI H4 protocol initialized[14315332.943679] Bluetooth: HCI BCSP protocol initialized[14315332.949029] cpuidle: using governor ladder[14315332.953490] cpuidle: using governor menu[14315332.963336] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2[14315332.994617] input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1[14315333.013341] input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input3[14315333.047434] input: USB HID v1.11 Keyboard [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:02.0-3[14315333.070002] input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input4[14315333.104253] input: USB HID v1.11 Device [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:02.0-3[14315333.114512] usbcore: registered new interface driver usbhid[14315333.120305] usbhid: v2.6:USB HID core driver[14315333.126452] Advanced Linux Sound Architecture Driver Version 1.0.16.[14315333.134233] ALSA device list:[14315333.137578] No soundcards found.[14315333.141510] GACT probability on[14315333.145020] Mirror/redirect action on[14315333.150212] u32 classifier[14315333.153287] Performance counters on[14315333.154901] input device check on [14315333.159018] Actions configured [14315333.166486] IPv4 over IPv4 tunneling driver[14315333.170629] ip_tables: (C) 2000-2006 Netfilter Core Team[14315333.176416] TCP bic registered[14315333.179848] TCP cubic registered[14315333.183441] TCP westwood registered[14315333.187300] TCP htcp registered[14315333.190813] TCP vegas registered[14315333.194411] TCP yeah registered[14315333.197923] Initializing XFRM netlink socket[14315333.202884] NET: Registered protocol family 10[14315333.210003] IPv6 over IPv4 tunneling driver[14315333.216669] NET: Registered protocol family 17[14315333.221405] NET: Registered protocol family 15[14315333.226324] Bridge firewalling registered[14315333.230726] Bluetooth: L2CAP ver 2.9[14315333.236670] Bluetooth: L2CAP socket layer initialized[14315333.240010] Bluetooth: SCO (Voice Link) ver 0.5[14315333.245429] Bluetooth: SCO socket layer initialized[14315333.250384] Bluetooth: RFCOMM socket layer initialized[14315333.255904] Bluetooth: RFCOMM TTY layer initialized[14315333.261155] Bluetooth: RFCOMM ver 1.8[14315333.266419] Bluetooth: BNEP (Ethernet Emulation) ver 1.2[14315333.270458] Bluetooth: HIDP (Human Interface Emulation) ver 1.2[14315333.277052] RPC: Registered udp transport module.[14315333.282436] RPC: Registered tcp transport module.[14315333.287563] 802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>[14315333.296237] All bugs added by David S. Miller <davem@xxxxxxxxxx>[14315333.300148] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3800+ processors (1 cpu cores) (version 2.20.00)[14315333.313310] powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x8[14315333.316895] powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa[14315333.323065] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc[14315333.335676] powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe[14315333.341612] powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12[14315333.350003] md: Autodetecting RAID arrays.[14315333.354367] md: Scanned 0 and added 0 devices.[14315333.358509] md: autorun ...[14315333.361835] md: ... autorun DONE.[14315333.381886] kjournald starting. Commit interval 5 seconds[14315333.387883] EXT3-fs: mounted filesystem with ordered data mode.[14315333.394472] VFS: Mounted root (ext3 filesystem) readonly.[14315333.400861] Freeing unused kernel memory: 260k freed[14315333.406477] Write protecting the kernel read-only data: 6480k[14315334.057088] Marking TSC unstable due to cpufreq changes[14315334.230019] Clocksource tsc unstable (delta = -103393192 ns)[14315336.340991] scsi6 : pata_amd[14315336.344444] scsi7 : pata_amd[14315336.349256] ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14[14315336.364276] ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15[14315336.559195] ata7.01: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-106S 0122, E1.22, max UDMA/66[14315336.581322] ata7.01: configured for UDMA/66[14315336.598214] scsi 6:0:1:0: CD-ROM PIONEER DVD-ROM DVD-106 1.22 PQ: 0 ANSI: 5[14315336.610878] sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray[14315336.617824] sr 6:0:1:0: Attached scsi generic sg2 type 5[14315336.639413] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22[14315336.645635] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 22[14315336.656334] ALSA sound/pci/hda/hda_intel.c:1904: chipset global capabilities = 0x4401[14315336.690054] ALSA sound/pci/hda/hda_intel.c:745: codec_mask = 0x1[14315336.728674] ALSA sound/pci/hda/hda_codec.c:2350: hda_codec: model '6stack-dig' is selected for config 1043:81f6 (Asus M2N-SLI)[14315337.118212] ALSA sound/pci/hda/hda_codec.c:1127: Cannot find slave Headphone Playback Volume, skipped[14315337.129724] ALSA sound/pci/hda/hda_codec.c:1127: Cannot find slave Mono Playback Volume, skipped[14315337.139447] ALSA sound/pci/hda/hda_codec.c:1127: Cannot find slave Speaker Playback Volume, skipped[14315337.148749] ALSA sound/pci/hda/hda_codec.c:1127: Cannot find slave Speaker Playback Switch, skipped[14315337.161249] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.[14315337.169779] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21[14315337.175914] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21[14315337.702535] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:17:31:aa:1e:89[14315337.711357] forcedeth 0000:00:08.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi msi-x desc-v3[14315337.750004] gameport: EMU10K1 is pci0000:01:08.1/gameport0, io 0x9800, speed 1201kHz[14315337.765496] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18[14315337.771668] ACPI: PCI Interrupt 0000:01:08.0[A] -> ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 20[14315337.783535] Link [APC3] -> GSI 18 (level, low) -> IRQ 18[14315337.797875] ACPI: PCI Interrupt 0000:00:09.0[A] -> ALSA sound/pci/emu10k1/emu10k1_main.c:1748: vendor=0x1102, device=0x2, subsystem_vendor_id=0x80641102, subsystem_id=0x8064[14315337.819202] Link [AMC1] -> GSI 20 (level, low) -> IRQ 20[14315337.833609] ALSA sound/pci/emu10k1/emu10k1_main.c:1773: Sound card name=SB Live 5.1[14315338.353675] forcedeth 0000:00:09.0: ifname eth1, PHY OUI 0x5043 @ 1, addr 00:17:31:ac:c6:64[14315338.362986] forcedeth 0000:00:09.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi msi-x desc-v3[14315339.093711] Adding 3911788k swap on /dev/sda6. Priority:-1 extents:1 across:3911788k[14315339.279495] EXT3 FS on sda5, internal journal[14315344.690008] br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.[14315356.516848] [14315356.516850] =================================[14315356.520007] [ INFO: inconsistent lock state ][14315356.520007] 2.6.26-rc4 #28[14315356.520007] ---------------------------------[14315356.520007] inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.[14315356.520007] ethtool/1985 [HC0[0]:SC0[1]:HE1:SE0] takes:[14315356.520007] (&np->lock){++..}, at: [<ffffffffa000c5fd>] nv_set_settings+0xc8/0x3de [forcedeth][14315356.520008] {in-hardirq-W} state was registered at:[14315356.520008] [<ffffffffffffffff>] 0xffffffffffffffff[14315356.520008] irq event stamp: 3606[14315356.520008] hardirqs last enabled at (3605): [<ffffffff8068106f>] _spin_unlock_irqrestore+0x3f/0x68[14315356.520008] hardirqs last disabled at (3604): [<ffffffff80680d38>] _spin_lock_irqsave+0x13/0x46[14315356.520008] softirqs last enabled at (3534): [<ffffffff80246ba5>] __do_softirq+0xbc/0xc5[14315356.520008] softirqs last disabled at (3606): [<ffffffff80680b33>] _spin_lock_bh+0x11/0x41[14315356.520008] [14315356.520008] other info that might help us debug this:[14315356.520008] 2 locks held by ethtool/1985:[14315356.520008] #0: (rtnl_mutex){--..}, at: [<ffffffff80596072>] rtnl_lock+0x12/0x14[14315356.520008] #1: (_xmit_ETHER){-+..}, at: [<ffffffffa000c5e8>] nv_set_settings+0xb3/0x3de [forcedeth][14315356.520008] [14315356.520008] stack backtrace:[14315356.520008] Pid: 1985, comm: ethtool Not tainted 2.6.26-rc4 #28[14315356.520008] [14315356.520008] Call Trace:[14315356.520008] [<ffffffff8025f190>] print_usage_bug+0x162/0x173[14315356.520008] [<ffffffff8025fa8b>] mark_lock+0x231/0x41f[14315356.520008] [<ffffffff802607cf>] __lock_acquire+0x4e7/0xcac[14315356.520008] [<ffffffff8025fe64>] ? trace_hardirqs_on+0xf1/0x115[14315356.520008] [<ffffffff80272c3a>] ? disable_irq_nosync+0x6f/0x7b[14315356.520008] [<ffffffff80261375>] lock_acquire+0x55/0x6e[14315356.520008] [<ffffffffa000c5fd>] ? :forcedeth:nv_set_settings+0xc8/0x3de[14315356.520008] [<ffffffff80680b15>] _spin_lock+0x2f/0x3c[14315356.520008] [<ffffffffa000c5fd>] :forcedeth:nv_set_settings+0xc8/0x3de[14315356.520008] [<ffffffff8058f8bb>] dev_ethtool+0x186/0xea3[14315356.520008] [<ffffffff8067f446>] ? mutex_lock_nested+0x243/0x275[14315356.520008] [<ffffffff8025df2b>] ? debug_mutex_free_waiter+0x46/0x4a[14315356.520008] [<ffffffff8067f469>] ? mutex_lock_nested+0x266/0x275[14315356.520008] [<ffffffff8058e1ce>] dev_ioctl+0x4eb/0x600[14315356.520008] [<ffffffff8068106f>] ? _spin_unlock_irqrestore+0x3f/0x68[14315356.520008] [<ffffffff80580f91>] sock_ioctl+0x1f5/0x202[14315356.520008] [<ffffffff802a322e>] vfs_ioctl+0x2a/0x77[14315356.520008] [<ffffffff802a34d6>] do_vfs_ioctl+0x25b/0x270[14315356.520008] [<ffffffff806807b6>] ? trace_hardirqs_on_thunk+0x35/0x3a[14315356.520008] [<ffffffff802a352d>] sys_ioctl+0x42/0x65[14315356.520008] [<ffffffff8021fffb>] system_call_after_swapgs+0x7b/0x80[14315356.520008] [14315356.786222] eth0: link down.[14315356.794850] eth1: link down.[14315356.812266] br0: port 2(eth1) entering disabled state[14315360.086673] eth1: link up.[14315360.086679] br0: port 2(eth1) entering learning state[14315360.850884] ALSA sound/pci/hda/hda_intel.c:1318: azx_pcm_prepare: bufsize=0x1800, format=0x4011[14315360.867017] ALSA sound/pci/hda/hda_codec.c:716: hda_codec_setup_stream: NID=0x2, stream=0x5, channel=0, format=0x4011[14315360.900023] ALSA sound/pci/hda/hda_codec.c:716: hda_codec_setup_stream: NID=0x4, stream=0x5, channel=0, format=0x4011[14315360.917746] ALSA sound/pci/hda/hda_codec.c:716: hda_codec_setup_stream: NID=0x6, stream=0x5, channel=0, format=0x4011[14315360.936740] ALSA sound/pci/hda/hda_codec.c:716: hda_codec_setup_stream: NID=0x5, stream=0x5, channel=0, format=0x4011[14315360.953352] ALSA sound/pci/hda/hda_codec.c:716: hda_codec_setup_stream: NID=0xa, stream=0x5, channel=0, format=0x4011[14315360.980039] ALSA sound/pci/hda/hda_codec.c:728: hda_codec_cleanup_stream: NID=0x4[14315360.989433] ALSA sound/pci/hda/hda_codec.c:728: hda_codec_cleanup_stream: NID=0x6[14315360.998047] ALSA sound/pci/hda/hda_codec.c:728: hda_codec_cleanup_stream: NID=0x5[14315361.010006] ALSA sound/pci/hda/hda_codec.c:728: hda_codec_cleanup_stream: NID=0xa[14315361.017106] ALSA sound/pci/hda/hda_codec.c:728: hda_codec_cleanup_stream: NID=0x2[14315361.096677] br0: topology change detected, propagating[14315361.102234] br0: port 2(eth1) entering forwarding state[14315361.127387] warning: `ntpd' uses 32-bit capabilities (legacy support in use)[14315370.790944] [drm] Initialized drm 1.1.0 20060810[14315370.863426] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16[14315370.873077] IOAPIC[0]: Set routing entry (4-16 -> 0x71 -> IRQ 16 Mode:1 Active:1)[14315370.878347] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16[14315370.887791] PCI: Setting latency timer of device 0000:02:00.0 to 64[14315370.894798] [drm] Initialized radeon 1.28.0 20060524 on minor 0[14315372.590005] [drm] Setting GART location based on new memory map[14315372.891221] [drm] Loading R300 Microcode[14315372.895667] [drm] writeback test succeeded in 1 usecs[14315498.823670] usb usb1: usb auto-resume[14315498.828106] ehci_hcd 0000:00:02.1: resume root hub[14315498.896667] hub 1-0:1.0: hub_resume[14315498.900484] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000[14315501.576676] hub 1-0:1.0: hub_suspend[14315501.580562] usb usb1: bus auto-suspend[14315501.584590] ehci_hcd 0000:00:02.1: suspend root hub[14315986.250681] PM: Hibernation mode set to 'platform'[14315986.262135] PM: Marking nosave pages: 000000000009f000 - 0000000000100000[14315986.268938] PM: Basic memory bitmaps created[14315986.275559] PM: Syncing filesystems ... done.[14315986.281302] Freezing user space processes ... (elapsed 0.01 seconds) done.[14315986.302172] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.[14315986.311774] PM: Shrinking memory... -done (0 pages freed)[14315986.381882] PM: Freed 0 kbytes in 0.06 seconds (0.00 MB/s)[14315986.391641] hub 2-0:1.0: hub_suspend[14315986.394524] usb usb2: bus suspend[14315986.397661] ohci_hcd 0000:00:02.0: suspend root hub[14315986.402857] sd 0:0:0:0: [sda] Synchronizing SCSI cache[14315986.416245] ACPI: PCI interrupt for device 0000:01:08.0 disabled[14315986.422433] ACPI handle has no context![14315986.437294] ACPI: PCI interrupt for device 0000:00:09.0 disabled[14315986.457213] ACPI: PCI interrupt for device 0000:00:08.0 disabled[14315986.489964] ACPI: PCI interrupt for device 0000:00:06.1 disabled[14315986.509671] ACPI: PCI interrupt for device 0000:00:05.2 disabled[14315986.513325] ACPI: PCI interrupt for device 0000:00:05.1 disabled[14315986.519720] ACPI: PCI interrupt for device 0000:00:05.0 disabled[14315986.526071] ata8: port disabled. ignoring.[14315986.532436] ACPI: PCI interrupt for device 0000:00:02.1 disabled[14315986.536836] ehci_hcd 0000:00:02.1: --> no state change[14315986.543206] ACPI: PCI interrupt for device 0000:00:02.0 disabled[14315986.548623] ohci_hcd 0000:00:02.0: --> no state change[14315986.555166] ACPI: Preparing to enter system sleep state S4[14315986.563274] Extended CMOS year: 2000[14315986.563274] PM: Creating hibernation image: [14315986.563274] PM: Need to copy 81901 pages[14315986.563274] PM: Normal pages needed: 81901 + 1024 + 38, available pages: 442001[14315986.563274] PM: Hibernation image created (81901 pages copied)[14315986.563274] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[14315986.563274] svm_cpu_init: svm_data is NULL on 0[14315986.563274] Extended CMOS year: 2000[14315986.578298] ACPI: Unable to turn cooling device [ffff81007f842f50] 'off'[14315986.585910] ohci_hcd 0000:00:02.0: PCI legacy resume[14315986.592483] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14315986.601596] PCI: Setting latency timer of device 0000:00:02.0 to 64[14315986.606980] ohci_hcd 0000:00:02.0: powerup ports[14315986.635128] ehci_hcd 0000:00:02.1: PCI legacy resume[14315986.639069] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14315986.648268] PCI: Setting latency timer of device 0000:00:02.1 to 64[14315986.654320] PM: Writing back config space on device 0000:00:04.0 at offset 1 (was b00001, writing b00005)[14315986.664193] PCI: Setting latency timer of device 0000:00:04.0 to 64[14315986.672444] PM: Writing back config space on device 0000:00:05.0 at offset 1 (was b00003, writing b00007)[14315986.686607] ata8: port disabled. ignoring.[14315986.689887] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14315986.698256] PCI: Setting latency timer of device 0000:00:05.0 to 64[14315986.704608] PM: Writing back config space on device 0000:00:05.1 at offset 1 (was b00003, writing b00007)[14315986.714616] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14315986.725062] PCI: Setting latency timer of device 0000:00:05.1 to 64[14315986.730649] PM: Writing back config space on device 0000:00:05.2 at offset 1 (was b00003, writing b00007)[14315986.740907] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14315986.751487] PCI: Setting latency timer of device 0000:00:05.2 to 64[14315986.757101] PCI: Setting latency timer of device 0000:00:06.0 to 64[14315986.776624] PM: Writing back config space on device 0000:00:06.1 at offset f (was 5020200, writing 5020205)[14315986.786839] PM: Writing back config space on device 0000:00:06.1 at offset 4 (was 0, writing fe020000)[14315986.796835] PM: Writing back config space on device 0000:00:06.1 at offset 1 (was b00000, writing b00002)[14315986.806652] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 22[14315986.815909] PCI: Setting latency timer of device 0000:00:06.1 to 64[14315986.841174] ata7.01: ACPI cmd ef/03:44:00:00:00:b0 filtered out[14315986.846526] ata7.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out[14315986.853216] ata7: nv_mode_filter: 0x1f01f&0x1f01f->0x1f01f, BIOS=0x1f000 (0xc50000) ACPI=0x1f01f (600:30:0x1c)[14315986.876773] ata7.01: configured for UDMA/66[14315987.026629] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14315987.044422] ata2: SATA link down (SStatus 0 SControl 300)[14315987.053013] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14315987.056619] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out[14315987.086474] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14315987.100696] ata4: SATA link down (SStatus 0 SControl 300)[14315987.106528] ata5: SATA link down (SStatus 0 SControl 300)[14315987.113327] ata6.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14315987.119156] ata3: SATA link down (SStatus 0 SControl 300)[14315987.130853] ata6.00: configured for UDMA/100[14315987.135041] ata1.00: configured for UDMA/133[14315987.139861] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315987.149821] sd 0:0:0:0: [sda] Write Protect is off[14315987.153694] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00[14315987.159532] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315987.253291] PM: Writing back config space on device 0000:00:08.0 at offset f (was 14010100, writing 1401010a)[14315987.263676] PM: Writing back config space on device 0000:00:08.0 at offset 7 (was 0, writing fe028000)[14315987.273674] PM: Writing back config space on device 0000:00:08.0 at offset 6 (was 0, writing fe029000)[14315987.283223] PM: Writing back config space on device 0000:00:08.0 at offset 5 (was 1, writing b001)[14315987.293222] PM: Writing back config space on device 0000:00:08.0 at offset 4 (was 0, writing fe02a000)[14315987.302646] PM: Writing back config space on device 0000:00:08.0 at offset 1 (was b00000, writing b00007)[14315987.313036] eth0: no link during initialization.[14315987.329957] PM: Writing back config space on device 0000:00:09.0 at offset f (was 14010100, writing 1401010a)[14315987.340347] PM: Writing back config space on device 0000:00:09.0 at offset 7 (was 0, writing fe025000)[14315987.350344] PM: Writing back config space on device 0000:00:09.0 at offset 6 (was 0, writing fe026000)[14315987.359896] PM: Writing back config space on device 0000:00:09.0 at offset 5 (was 1, writing ac01)[14315987.369897] PM: Writing back config space on device 0000:00:09.0 at offset 4 (was 0, writing fe027000)[14315987.379327] PM: Writing back config space on device 0000:00:09.0 at offset 1 (was b00000, writing b00007)[14315987.392577] PCI: Setting latency timer of device 0000:00:0a.0 to 64[14315987.397575] PCI: Setting latency timer of device 0000:00:0e.0 to 64[14315987.416636] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18[14315987.435121] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16[14315987.444992] PCI: Setting latency timer of device 0000:02:00.0 to 64[14315987.450509] sd 0:0:0:0: [sda] Starting disk[14315987.461766] usb usb1: usb resume[14315987.468753] ehci_hcd 0000:00:02.1: resume root hub[14315987.536706] hub 1-0:1.0: hub_resume[14315987.540738] usb usb2: usb resume[14315987.544405] ohci_hcd 0000:00:02.0: resume root hub[14315987.616616] hub 2-0:1.0: hub_resume[14315987.620615] PM: writing image.[14315987.624243] PM: Free swap pages: 977947[14315987.631831] PM: Saving image data pages (82061 pages) ... 0% 1% 2% 3% 4% 5% 6% 7% 8% 9% 10% 11% 12% 13% 14% 15% 16% 17% 18% 19% 20% 21% 22% 23% 24% 25% 26% 27% 28% 29% 30% 31% 32% 33% 34% 35% 36% 37% 38% 39% 40% 41% 42% 43% 44% 45% 46% 47% 48% 49% 50% 51% 52% 53% 54% 55% 56% 57% 58% 59% 60% 61% 62% 63% 64% 65% 66% 67% 68% 69% 70% 71% 72% 73% 74% 75% 76% 77% 78% 79% 80% 81% 82% 83% 84% 85% 86% 87% 88% 89% 90% 91% 92% 93% 94% 95% 96% 97% 98% 99%100%done[14315991.823947] PM: Wrote 328244 kbytes in 4.18 seconds (78.52 MB/s)[14315991.831374] PM: S|[14315992.111206] ohci_hcd 0000:00:02.0: Unlink after no-IRQ? Controller is probably using the wrong IRQ.[14315992.125935] usb 2-3: usb suspend[14315992.140442] usb 2-1: usb suspend[14315992.156628] hub 2-0:1.0: hub_suspend[14315992.160623] usb usb2: bus suspend[14315992.164341] ohci_hcd 0000:00:02.0: suspend root hub[14315992.169625] hub 1-0:1.0: hub_suspend[14315992.176288] usb usb1: bus suspend[14315992.177833] ehci_hcd 0000:00:02.1: suspend root hub[14315992.182633] sd 0:0:0:0: [sda] Synchronizing SCSI cache[14315992.189475] sd 0:0:0:0: [sda] Stopping disk[14315992.623539] ACPI: PCI interrupt for device 0000:01:08.0 disabled[14315992.630323] ACPI handle has no context![14315992.686627] ACPI: PCI interrupt for device 0000:00:06.1 disabled[14315992.706451] ACPI: PCI interrupt for device 0000:00:05.2 disabled[14315992.723228] ACPI: PCI interrupt for device 0000:00:05.1 disabled[14315992.739839] ACPI: PCI interrupt for device 0000:00:05.0 disabled[14315992.756495] ata8: port disabled. ignoring.[14315992.771213] ACPI: PCI interrupt for device 0000:00:02.1 disabled[14315992.789743] ehci_hcd 0000:00:02.1: --> PCI D3/wakeup[14315992.792010] ACPI: PCI interrupt for device 0000:00:02.0 disabled[14315992.811783] ohci_hcd 0000:00:02.0: --> PCI D3/wakeup[14315992.815627] ACPI: Preparing to enter system sleep state S4[14315992.825538] Extended CMOS year: 2000[14315992.826645] hwsleep-0324 [03] enter_sleep_state : Entering sleep state [S4] [ 0.000000] Linux version 2.6.26-rc4 (ranma@melchior) (gcc version 4.2.3 (Debian 4.2.3-5)) #28 PREEMPT Sun Jun 1 09:06:24 CEST 2008[ 0.000000] Command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose console=ttyS0,115200 console=tty0 pci=nomsi no_console_suspend ro[ 0.000000] BIOS-provided physical RAM map:[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)[ 0.000000] BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)[ 0.000000] max_pfn_mapped = 1048576[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[ 0.000000] init_memory_mapping[ 0.000000] DMI 2.4 present.[ 0.000000] ACPI: RSDP 000F7D20, 0024 (r2 Nvidia)[ 0.000000] ACPI: XSDT 7FEE3100, 004C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: FACP 7FEEADC0, 00F4 (r3 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: DSDT 7FEE3280, 7ACE (r1 NVIDIA AWRDACPI 1000 MSFT 3000000)[ 0.000000] ACPI: FACS 7FEE0000, 0040[ 0.000000] ACPI: SSDT 7FEEB000, 0136 (r1 PTLTD POWERNOW 1 LTP 1)[ 0.000000] ACPI: HPET 7FEEB180, 0038 (r1 Nvidia ASUSACPI 42302E31 AWRD 98)[ 0.000000] ACPI: MCFG 7FEEB200, 003C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: APIC 7FEEAF00, 0098 (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] early res: 0 [0-fff] BIOS data page[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE[ 0.000000] early res: 2 [200000-d3638f] TEXT DATA BSS[ 0.000000] early res: 3 [9f800-fffff] BIOS reserved[ 0.000000] early res: 4 [8000-bfff] PGTABLE[ 0.000000] Zone PFN ranges:[ 0.000000] DMA 0 -> 4096[ 0.000000] DMA32 4096 -> 1048576[ 0.000000] Normal 1048576 -> 1048576[ 0.000000] Movable zone start PFN for each node[ 0.000000] early_node_map[2] active PFN ranges[ 0.000000] 0: 0 -> 159[ 0.000000] 0: 256 -> 524000[ 0.000000] Detected use of extended apic ids on hypertransport bus[ 0.000000] ACPI: PM-Timer IO Port: 0x1008[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)[ 0.000000] Setting APIC routing to flat[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000[ 0.000000] Using ACPI (MADT) for SMP configuration information[ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000)[ 0.000000] mapped IOAPIC to ffffffffff5fa000 (00000000fec00000)[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)[14315324.233334] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 513763[14315324.233334] Kernel command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose console=ttyS0,115200 console=tty0 pci=nomsi no_console_suspend ro[14315324.233334] Initializing CPU#0[14315324.233334] PID hash table entries: 4096 (order: 12, 32768 bytes)[14315324.233334] Extended CMOS year: 2000[14315324.233334] TSC calibrated against PM_TIMER[14315324.233334] time.c: Detected 2411.116 MHz processor.[14315324.233334] Console: colour VGA+ 80x60[14315324.233334] console [tty0] enabled[14315324.233334] console [ttyS0] enabled[14315324.233334] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar[14315324.233334] ... MAX_LOCKDEP_SUBCLASSES: 8[14315324.233334] ... MAX_LOCK_DEPTH: 48[14315324.233334] ... MAX_LOCKDEP_KEYS: 2048[14315324.233334] ... CLASSHASH_SIZE: 1024[14315324.233334] ... MAX_LOCKDEP_ENTRIES: 8192[14315324.233334] ... MAX_LOCKDEP_CHAINS: 16384[14315324.233334] ... CHAINHASH_SIZE: 8192[14315324.233334] memory used by lock dependency info: 1648 kB[14315324.233334] per task-struct memory footprint: 2688 bytes[14315324.233334] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)[14315324.233334] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)[14315324.233334] Checking aperture...[14315324.233334] Node 0: aperture @ 289c000000 size 32 MB[14315324.233334] Aperture beyond 4GB. Ignoring.[14315324.233334] No AGP bridge found[14315324.233334] Memory: 2051692k/2096000k available (4624k kernel code, 43544k reserved, 2268k data, 260k init)[14315324.316528] Calibrating delay using timer specific routine.. 4827.99 BogoMIPS (lpj=8043188)[14315324.322866] Mount-cache hash table entries: 256[14315324.327216] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)[14315324.333327] CPU: L2 Cache: 512K (64 bytes/line)[14315324.336660] CPU: AMD Athlon(tm) 64 Processor 3800+ stepping 01[14315324.342949] ACPI: Core revision 20080321[14315324.359992] Parsing all Control Methods:[14315324.364011] Table [DSDT](id 0001) - 1203 Objects with 101 Devices 380 Methods 44 Regions[14315324.369992] Parsing all Control Methods:[14315324.373967] Table [SSDT](id 0002) - 4 Objects with 0 Devices 0 Methods 0 Regions[14315324.379991] tbxface-0598 [02] tb_load_namespace : ACPI Tables successfully acquired[14315324.389990] evxfevnt-0091 [02] enable : Transition to ACPI mode successful[14315324.398905] enabled ExtINT on CPU#0[14315324.403006] ENABLING IO-APIC IRQs[14315324.406656] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1[14315324.442963] Using local APIC timer interrupts.[14315324.449986] Detected 12.557 MHz APIC timer.[14315324.453320] net_namespace: 1272 bytes[14315324.456653] NET: Registered protocol family 16[14315324.460279] No dock devices found.[14315324.464209] TOM: 0000000080000000 aka 2048M[14315324.468810] ACPI: bus type pci registered[14315324.473327] PCI: Using configuration type 1 for base access[14315324.485055] evgpeblk-0956 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9[14315324.494056] evgpeblk-0956 [04] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9[14315324.513173] Completing Region/Field/Buffer/Package initialization:...................................................................................................................................................................................[14315324.548804] Initialized 39/44 Regions 11/11 Fields 40/40 Buffers 89/101 Packages (1216 nodes)[14315324.553313] Initializing Device/Processor/Thermal objects by executing _INI methods:...[14315324.559599] Executed 3 _INI methods requiring 1 _STA executions (examined 108 objects)[14315324.563312] evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 0 Runtime GPEs in this block[14315324.573312] evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 1 Runtime GPEs in this block[14315324.583311] ACPI: Interpreter enabled[14315324.586644] ACPI: (supports S0 S1 S3 S4 S5)[14315324.591289] ACPI: Using IOAPIC for interrupt routing[14315324.618925] ACPI: PCI Root Bridge [PCI0] (0000:00)[14315324.623308] PCI: Transparent bridge - 0000:00:06.0[14315324.717297] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.726104] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.731566] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 *10 11 14 15)[14315324.739052] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.744887] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.753505] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.762300] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)[14315324.766634] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.771942] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.778222] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)[14315324.785019] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)[14315324.792423] ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)[14315324.796634] ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)[14315324.800686] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.809480] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)[14315324.813829] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)[14315324.821297] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.830093] ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)[14315324.837596] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)[14315324.845095] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)[14315324.852709] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.[14315324.856634] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.[14315324.860580] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0[14315324.866844] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.[14315324.874099] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.[14315324.881348] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.[14315324.888598] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0[14315324.893301] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.[14315324.898761] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0[14315324.903301] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0[14315324.906634] ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0[14315324.910582] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.[14315324.918714] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0[14315324.923301] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0[14315324.926634] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0[14315324.930582] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.[14315324.938324] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.[14315324.946569] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0[14315324.950580] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0[14315324.957634] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0[14315324.964780] Linux Plug and Play Support v0.97 (c) Adam Belay[14315324.969968] pnp: PnP ACPI init[14315324.973301] ACPI: bus type pnp registered[14315324.985823] pnp: PnP ACPI: found 13 devices[14315324.989968] ACPI: ACPI bus type pnp unregistered[14315324.993301] SCSI subsystem initialized[14315324.996759] usbcore: registered new interface driver usbfs[14315325.002670] usbcore: registered new interface driver hub[14315325.006635] usbcore: registered new device driver usb[14315325.009968] PCI: Using ACPI for IRQ routing[14315325.013301] testing the IO APIC.......................[14315325.016635] [14315325.016635] .................................... done.[14315325.031049] Bluetooth: Core ver 2.11[14315325.035185] NET: Registered protocol family 31[14315325.039968] Bluetooth: HCI device and connection manager initialized[14315325.043301] Bluetooth: HCI socket layer initialized[14315325.046635] DMAR:parse DMAR table failure.[14315325.057361] system 00:01: ioport range 0x1000-0x107f has been reserved[14315325.064251] system 00:01: ioport range 0x1080-0x10ff has been reserved[14315325.071137] system 00:01: ioport range 0x1400-0x147f has been reserved[14315325.078022] system 00:01: ioport range 0x1480-0x14ff has been reserved[14315325.084910] system 00:01: ioport range 0x1800-0x187f has been reserved[14315325.091796] system 00:01: ioport range 0x1880-0x18ff has been reserved[14315325.098693] system 00:02: ioport range 0x4d0-0x4d1 has been reserved[14315325.105406] system 00:02: ioport range 0x800-0x87f has been reserved[14315325.112119] system 00:02: ioport range 0x290-0x297 has been reserved[14315325.118858] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved[14315325.126797] system 00:0c: iomem range 0xcd000-0xcffff has been reserved[14315325.133778] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved[14315325.143248] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved[14315325.150653] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved[14315325.158059] system 00:0c: iomem range 0xfefff000-0xfefff0ff could not be reserved[14315325.165984] system 00:0c: iomem range 0x7fee0000-0x7fefffff could not be reserved[14315325.173440] system 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved[14315325.181365] system 00:0c: iomem range 0x0-0x9ffff could not be reserved[14315325.188337] system 00:0c: iomem range 0x100000-0x7fedffff could not be reserved[14315325.202969] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved[14315325.210022] system 00:0c: iomem range 0xfee00000-0xfeefffff could not be reserved[14315325.217947] system 00:0c: iomem range 0xfefff000-0xfeffffff could not be reserved[14315325.225900] system 00:0c: iomem range 0xfff80000-0xfff80fff could not be reserved[14315325.233830] system 00:0c: iomem range 0xfff90000-0xfffbffff could not be reserved[14315325.241760] system 00:0c: iomem range 0xfffed000-0xfffeffff could not be reserved[14315325.250722] PCI: Bridge: 0000:00:06.0[14315325.254332] IO window: 9000-9fff[14315325.258111] MEM window: disabled.[14315325.263163] PREFETCH window: disabled.[14315325.267029] PCI: Bridge: 0000:00:0a.0[14315325.271058] IO window: 8000-8fff[14315325.274831] MEM window: 0xfde00000-0xfdefffff[14315325.279727] PREFETCH window: 0x00000000e8000000-0x00000000efffffff[14315325.286443] PCI: Bridge: 0000:00:0e.0[14315325.290472] IO window: 6000-7fff[14315325.294245] MEM window: 0xfdd00000-0xfddfffff[14315325.299141] PREFETCH window: disabled.[14315325.303509] NET: Registered protocol family 2[14315325.339327] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)[14315325.347472] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)[14315325.356669] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)[14315325.369177] TCP: Hash tables configured (established 262144 bind 65536)[14315325.376181] TCP reno registered[14315325.389176] NET: Registered protocol family 1[14315325.395754] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).[14315325.402891] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.[14315325.409416] fuse init (API version 7.9)[14315325.413774] SGI XFS with security attributes, large block/inode numbers, no debug enabled[14315325.422698] msgmni has been set to 4007 for ipc namespace ffffffff808882f0[14315325.430145] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)[14315325.437997] io scheduler noop registered[14315325.443166] io scheduler anticipatory registered[14315325.447466] io scheduler deadline registered[14315325.452480] io scheduler cfq registered (default)[14315325.469713] pci 0000:00:05.0: Enabling HT MSI Mapping[14315325.475169] pci 0000:00:05.1: Enabling HT MSI Mapping[14315325.480288] pci 0000:00:05.2: Enabling HT MSI Mapping[14315325.485738] pci 0000:00:06.0: Enabling HT MSI Mapping[14315325.491174] pci 0000:00:06.1: Enabling HT MSI Mapping[14315325.496626] pci 0000:00:08.0: Enabling HT MSI Mapping[14315325.502069] pci 0000:00:09.0: Enabling HT MSI Mapping[14315325.507500] pci 0000:00:0a.0: Enabling HT MSI Mapping[14315325.512953] pci 0000:00:0e.0: Enabling HT MSI Mapping[14315325.518653] assign_interrupt_mode Found MSI capability[14315325.523975] assign_interrupt_mode Found MSI capability[14315325.530243] input: Power Button (FF) as /class/input/input0[14315325.536222] ACPI: Power Button (FF) [PWRF][14315325.540812] input: Power Button (CM) as /class/input/input1[14315325.546753] ACPI: Power Button (CM) [PWRB][14315325.552821] ACPI: PNP0C0B:00 is registered as cooling_device0[14315325.558944] ACPI: Fan [FAN] (on)[14315325.562831] ACPI: ACPI0007:00 is registered as cooling_device1[14315325.570104] ACPI: Expecting a [Reference] package element, found type 0[14315325.577473] ACPI: LNXTHERM:01 is registered as thermal_zone0[14315325.583938] ACPI: Thermal Zone [THRM] (40 C)[14315325.610263] Real Time Clock Driver v1.12ac[14315325.614742] Linux agpgart interface v0.103[14315325.619213] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled[14315325.629426] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A[14315325.636741] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A[14315325.644310] loop: module loaded[14315325.647672] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2[14315325.654153] e1000e: Copyright (c) 1999-2008 Intel Corporation.[14315325.660478] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI[14315325.666934] e100: Copyright(c) 1999-2006 Intel Corporation[14315325.672973] tun: Universal TUN/TAP device driver, 1.6[14315325.678389] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>[14315325.685197] Driver 'sd' needs updating - please use bus_type methods[14315325.691990] Driver 'sr' needs updating - please use bus_type methods[14315325.699727] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23[14315325.705854] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14315325.715675] sata_nv 0000:00:05.0: Using SWNCQ mode[14315325.720975] scsi0 : sata_nv[14315325.724440] scsi1 : sata_nv[14315325.728031] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 23[14315325.736121] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 23[14315326.213362] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14315326.243549] ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7[14315326.249924] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)[14315326.263860] ata1.00: configured for UDMA/133[14315326.597023] ata2: SATA link down (SStatus 0 SControl 300)[14315326.616245] isa bounce pool size: 16 pages[14315326.620287] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5[14315326.629360] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315326.636789] sd 0:0:0:0: [sda] Write Protect is off[14315326.641991] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315326.652984] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315326.660029] sd 0:0:0:0: [sda] Write Protect is off[14315326.664333] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315326.673832] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >[14315326.733373] sd 0:0:0:0: [sda] Attached SCSI disk[14315326.741834] sd 0:0:0:0: Attached scsi generic sg0 type 0[14315326.749400] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22[14315326.755559] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14315326.766066] sata_nv 0000:00:05.1: Using SWNCQ mode[14315326.771298] scsi2 : sata_nv[14315326.774646] scsi3 : sata_nv[14315326.779736] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 22[14315326.786676] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 22[14315327.120357] ata3: SATA link down (SStatus 0 SControl 300)[14315327.467022] ata4: SATA link down (SStatus 0 SControl 300)[14315327.486670] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21[14315327.492679] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14315327.501079] sata_nv 0000:00:05.2: Using SWNCQ mode[14315327.506771] scsi4 : sata_nv[14315327.510118] scsi5 : sata_nv[14315327.513669] ata5: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb400 irq 21[14315327.521249] ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb800 bmdma 0xb408 irq 21[14315327.857023] ata5: SATA link down (SStatus 0 SControl 300)[14315328.346694] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14315328.360110] ata6.00: ATAPI: TSSTcorp CDDVDW SH-S203B, SB00, max UDMA/100[14315328.380111] ata6.00: configured for UDMA/100[14315328.398843] scsi 5:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S203B SB00 PQ: 0 ANSI: 5[14315328.410003] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray[14315328.416674] Uniform CD-ROM driver Revision: 3.20[14315328.423724] sr 5:0:0:0: Attached scsi generic sg1 type 5[14315328.435246] block2mtd: version $Revision: 1.30 $[14315328.442473] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20[14315328.446685] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14315328.457118] ehci_hcd 0000:00:02.1: EHCI Host Controller[14315328.463634] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1[14315328.471119] ehci_hcd 0000:00:02.1: debug port 1[14315328.476547] ehci_hcd 0000:00:02.1: irq 20, io mem 0xfe02e000[14315328.491682] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004[14315328.500162] usb usb1: configuration #1 chosen from 1 choice[14315328.506296] hub 1-0:1.0: USB hub found[14315328.510445] hub 1-0:1.0: 10 ports detected[14315328.616897] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002[14315328.624059] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1[14315328.631737] usb usb1: Product: EHCI Host Controller[14315328.638403] usb usb1: Manufacturer: Linux 2.6.26-rc4 ehci_hcd[14315328.643654] usb usb1: SerialNumber: 0000:00:02.1[14315328.650676] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23[14315328.656787] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14315328.666056] ohci_hcd 0000:00:02.0: OHCI Host Controller[14315328.673336] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2[14315328.680048] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000[14315328.739096] usb usb2: configuration #1 chosen from 1 choice[14315328.745173] hub 2-0:1.0: USB hub found[14315328.749310] hub 2-0:1.0: 10 ports detected[14315328.826737] hub 1-0:1.0: unable to enumerate USB device on port 1[14315328.859995] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001[14315328.866675] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1[14315328.873961] usb usb2: Product: OHCI Host Controller[14315328.879205] usb usb2: Manufacturer: Linux 2.6.26-rc4 ohci_hcd[14315328.883557] usb usb2: SerialNumber: 0000:00:02.0[14315328.889802] USB Universal Host Controller Interface driver v3.0[14315329.030024] hub 1-0:1.0: unable to enumerate USB device on port 3[14315329.206690] hub 1-0:1.0: unable to enumerate USB device on port 4[14315329.213291] usbcore: registered new interface driver usblp[14315329.220135] PNP: No PS/2 controller found. Probing ports directly.[14315329.227168] serio: i8042 KBD port at 0x60,0x64 irq 1[14315329.232704] serio: i8042 AUX port at 0x60,0x64 irq 12[14315329.238736] mice: PS/2 mouse device common for all mice[14315329.263258] i2c /dev entries driver[14315329.267314] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00[14315329.273623] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40[14315329.279949] it87: Found IT8716F chip at 0x290, revision 0[14315329.283937] it87: in3 is VCC (+5V)[14315329.289850] it87: in7 is VCCH (+5V Stand-By)[14315329.320001] md: raid1 personality registered for level 1[14315329.327686] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx[14315329.339952] Bluetooth: HCI USB driver ver 2.9[14315329.493345] usb 2-1: new low speed USB device using ohci_hcd and address 2[14315329.680026] usb 2-1: configuration #1 chosen from 1 choice[14315329.703336] usb 2-1: New USB device found, idVendor=045e, idProduct=0040[14315329.710017] usb 2-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0[14315329.717602] usb 2-1: Product: Microsoft 3-Button Mouse with IntelliEye(TM)[14315329.726619] usb 2-1: Manufacturer: Microsoft[14315330.006678] usb 2-3: new low speed USB device using ohci_hcd and address 3[14315330.200012] usb 2-3: configuration #1 chosen from 1 choice[14315330.236669] usb 2-3: New USB device found, idVendor=045e, idProduct=00db[14315330.243350] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0[14315330.250927] usb 2-3: Product: Natural® Ergonomic Keyboard 4000[14315330.257121] usb 2-3: Manufacturer: Microsoft[14315330.540011] usb 2-4: new full speed USB device using ohci_hcd and address 4[14315330.713344] usb 2-4: device descriptor read/64, error -62[14315330.986677] usb 2-4: device descriptor read/64, error -62[14315331.253344] usb 2-4: new full speed USB device using ohci_hcd and address 5[14315331.426677] usb 2-4: device descriptor read/64, error -62[14315331.700011] usb 2-4: device descriptor read/64, error -62[14315331.966678] usb 2-4: new full speed USB device using ohci_hcd and address 6[14315332.380008] usb 2-4: device not accepting address 6, error -62[14315332.543344] usb 2-4: new full speed USB device using ohci_hcd and address 7[14315332.956675] usb 2-4: device not accepting address 7, error -62[14315332.962884] hub 2-0:1.0: unable to enumerate USB device on port 4[14315332.969681] usbcore: registered new interface driver hci_usb[14315332.976016] Bluetooth: HCI UART driver ver 2.2[14315332.982175] Bluetooth: HCI H4 protocol initialized[14315332.986991] Bluetooth: HCI BCSP protocol initialized[14315332.992341] cpuidle: using governor ladder[14315332.996802] cpuidle: using governor menu[14315333.006669] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2[14315333.037967] input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1[14315333.056674] input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input3[14315333.090722] input: USB HID v1.11 Keyboard [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:02.0-3[14315333.113335] input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input4[14315333.147542] input: USB HID v1.11 Device [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:02.0-3[14315333.157794] usbcore: registered new interface driver usbhid[14315333.163615] usbhid: v2.6:USB HID core driver[14315333.169753] Advanced Linux Sound Architecture Driver Version 1.0.16.[14315333.177526] ALSA device list:[14315333.180871] No soundcards found.[14315333.184803] GACT probability on[14315333.188313] Mirror/redirect action on[14315333.193511] u32 classifier[14315333.196590] Performance counters on[14315333.198201] input device check on [14315333.202321] Actions configured [14315333.209755] IPv4 over IPv4 tunneling driver[14315333.213971] ip_tables: (C) 2000-2006 Netfilter Core Team[14315333.219759] TCP bic registered[14315333.223189] TCP cubic registered[14315333.226782] TCP westwood registered[14315333.230632] TCP htcp registered[14315333.234141] TCP vegas registered[14315333.237735] TCP yeah registered[14315333.241240] Initializing XFRM netlink socket[14315333.246173] NET: Registered protocol family 10[14315333.253336] IPv6 over IPv4 tunneling driver[14315333.260003] NET: Registered protocol family 17[14315333.266655] NET: Registered protocol family 15[14315333.270137] Bridge firewalling registered[14315333.274547] Bluetooth: L2CAP ver 2.9[14315333.278487] Bluetooth: L2CAP socket layer initialized[14315333.283907] Bluetooth: SCO (Voice Link) ver 0.5[14315333.288799] Bluetooth: SCO socket layer initialized[14315333.293704] Bluetooth: RFCOMM socket layer initialized[14315333.299223] Bluetooth: RFCOMM TTY layer initialized[14315333.304474] Bluetooth: RFCOMM ver 1.8[14315333.309739] Bluetooth: BNEP (Ethernet Emulation) ver 1.2[14315333.313777] Bluetooth: HIDP (Human Interface Emulation) ver 1.2[14315333.320383] RPC: Registered udp transport module.[14315333.325755] RPC: Registered tcp transport module.[14315333.330882] 802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>[14315333.339565] All bugs added by David S. Miller <davem@xxxxxxxxxx>[14315333.343476] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3800+ processors (1 cpu cores) (version 2.20.00)[14315333.356638] powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x8[14315333.360223] powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa[14315333.366392] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc[14315333.379005] powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe[14315333.384939] powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12[14315333.397176] Freezing user space processes ... (elapsed 0.00 seconds) done.[14315333.405713] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.[14315333.413728] PM: Loading image data pages (82061 pages) ... 0% 1% 2% 3% 4% 5% 6% 7% 8%Marking TSC unstable due to cpufreq changes[14315334.100080] 9% 10% 11% 12% 13% 14% 15% 16% 17% 18% 19% 20% 21% 22% 23%<4>Clocksource tsc unstable (delta = -83348826 ns)[14315334.761277] 24% 25% 26% 27% 28% 29% 30% 31% 32% 33% 34% 35% 36% 37% 38% 39% 40% 41% 42% 43% 44% 45% 46% 47% 48% 49% 50% 51% 52% 53% 54% 55% 56% 57% 58% 59% 60% 61% 62% 63% 64% 65% 66% 67% 68% 69% 70% 71% 72% 73% 74% 75% 76% 77% 78% 79% 80% 81% 82% 83% 84% 85% 86% 87% 88% 89% 90% 91% 92% 93% 94% 95% 96% 97% 98% 99%100%done[14315338.103363] PM: Read 328244 kbytes in 4.69 seconds (69.98 MB/s)[14315338.118467] sd 0:0:0:0: [sda] Synchronizing SCSI cache[14315338.125657] ACPI: PCI interrupt for device 0000:00:05.2 disabled[14315338.132768] ACPI: PCI interrupt for device 0000:00:05.1 disabled[14315338.139434] ACPI: PCI interrupt for device 0000:00:05.0 disabled[14315338.145877] ACPI: PCI interrupt for device 0000:00:02.0 disabled[14315338.152470] Extended CMOS year: 2000[14315986.563274] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[14315986.563274] evxfevnt-0079 [02] enable : System is already in ACPI mode[14315986.563274] svm_cpu_init: svm_data is NULL on 0[14315986.563274] Extended CMOS year: 2000[14315986.589380] ACPI: Unable to turn cooling device [ffff81007f842f50] 'off'[14315986.595650] ohci_hcd 0000:00:02.0: PCI legacy resume[14315986.602250] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14315986.610740] PCI: Setting latency timer of device 0000:00:02.0 to 64[14315986.616840] ohci_hcd 0000:00:02.0: lost power[14315986.676746] ohci_hcd 0000:00:02.0: OHCI controller state[14315986.682550] ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers[14315986.689553] ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3[14315986.699552] ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0[14315986.703045] ohci_hcd 0000:00:02.0: intrstatus 0x00000044 RHSC SF[14315986.709712] ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH[14315986.716023] ohci_hcd 0000:00:02.0: hcca frame #002b[14315986.722593] ohci_hcd 0000:00:02.0: roothub.a 0100120a POTPGT=1 NOCP NPS NDP=10(10)[14315986.728984] ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000[14315986.735900] ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE[14315986.742568] ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS[14315986.752122] ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS[14315986.757264] ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00010301 CSC LSDA PPS CCS[14315986.765496] ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00010101 CSC PPS CCS[14315986.775496] ohci_hcd 0000:00:02.0: roothub.portstatus [4] 0x00000100 PPS[14315986.780480] ohci_hcd 0000:00:02.0: roothub.portstatus [5] 0x00000100 PPS[14315986.787580] ohci_hcd 0000:00:02.0: roothub.portstatus [6] 0x00000100 PPS[14315986.794677] ohci_hcd 0000:00:02.0: roothub.portstatus [7] 0x00000100 PPS[14315986.801774] ohci_hcd 0000:00:02.0: roothub.portstatus [8] 0x00000100 PPS[14315986.808870] ohci_hcd 0000:00:02.0: roothub.portstatus [9] 0x00000100 PPS[14315986.815970] ohci_hcd 0000:00:02.0: restart complete[14315986.822637] usb usb2: root hub lost power or was reset[14315986.827920] ohci_hcd 0000:00:02.0: suspend root hub[14315986.832075] ehci_hcd 0000:00:02.1: PCI legacy resume[14315986.838745] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14315986.847146] PCI: Setting latency timer of device 0000:00:02.1 to 64[14315986.853423] ehci_hcd 0000:00:02.1: lost power, restarting[14315986.859232] usb usb1: root hub lost power or was reset[14315986.865901] ehci_hcd 0000:00:02.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT[14315986.874772] ehci_hcd 0000:00:02.1: debug port 1[14315986.878896] PCI: cache line size of 64 is not supported by device 0000:00:02.1[14315986.888901] PM: Writing back config space on device 0000:00:04.0 at offset b (was 82391043, writing 8239f043)[14315986.897045] PCI: Setting latency timer of device 0000:00:04.0 to 64[14315986.910015] ata8: port disabled. ignoring.[14315986.914630] PM: Writing back config space on device 0000:00:05.0 at offset 1 (was b00003, writing b00007)[14315986.924729] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14315986.934453] PCI: Setting latency timer of device 0000:00:05.0 to 64[14315986.941010] PM: Writing back config space on device 0000:00:05.1 at offset 1 (was b00003, writing b00007)[14315986.951635] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14315986.961165] PCI: Setting latency timer of device 0000:00:05.1 to 64[14315986.968038] PM: Writing back config space on device 0000:00:05.2 at offset 1 (was b00003, writing b00007)[14315986.978536] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14315986.988059] PCI: Setting latency timer of device 0000:00:05.2 to 64[14315986.994917] PCI: Setting latency timer of device 0000:00:06.0 to 64[14315987.013297] PM: Writing back config space on device 0000:00:06.1 at offset 1 (was b00006, writing b00002)[14315987.023378] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 22[14315987.032679] PCI: Setting latency timer of device 0000:00:06.1 to 64[14315987.085970] ata7.01: ACPI cmd ef/03:44:00:00:00:b0 filtered out[14315987.089928] ata7.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out[14315987.096627] ata7: nv_mode_filter: 0x1f01f&0x1f01f->0x1f01f, BIOS=0x1f000 (0xc50000) ACPI=0x1f01f (600:30:0x1c)[14315987.113600] ata7.01: configured for UDMA/66[14315987.263295] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14315987.325767] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14315987.352457] ata2: SATA link down (SStatus 0 SControl 300)[14315987.357660] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14315987.363714] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out[14315987.370155] ata6.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14315987.379831] ata3: SATA link down (SStatus 0 SControl 300)[14315987.382567] ata5: SATA link down (SStatus 0 SControl 300)[14315987.389289] ata4: SATA link down (SStatus 0 SControl 300)[14315987.395472] ata6.00: configured for UDMA/100[14315987.401731] ata1.00: configured for UDMA/133[14315987.405175] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315987.412932] sd 0:0:0:0: [sda] Write Protect is off[14315987.419578] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00[14315987.424926] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315987.467065] eth0: no link during initialization.[14315987.484033] PCI: Setting latency timer of device 0000:00:0a.0 to 64[14315987.491779] PCI: Setting latency timer of device 0000:00:0e.0 to 64[14315987.509959] PM: Writing back config space on device 0000:01:08.0 at offset 1 (was 2900005, writing 2900001)[14315987.520213] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18[14315987.537783] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16[14315987.548735] PCI: Setting latency timer of device 0000:02:00.0 to 64[14315987.555499] sd 0:0:0:0: [sda] Starting disk[14315987.585461] usb usb1: usb resume[14315987.609591] ehci_hcd 0000:00:02.1: resume root hub after power loss[14315987.689950] ehci_hcd 0000:00:02.1: port 4 low speed --> companion[14315987.696455] ehci_hcd 0000:00:02.1: port 3 low speed --> companion[14315987.703118] ehci_hcd 0000:00:02.1: port 1 low speed --> companion[14315987.799951] ehci_hcd 0000:00:02.1: GetStatus port 4 status 003402 POWER OWNER sig=k CSC[14315987.808460] ehci_hcd 0000:00:02.1: GetStatus port 3 status 003402 POWER OWNER sig=k CSC[14315987.818459] ehci_hcd 0000:00:02.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC[14315987.836617] hub 1-0:1.0: hub_reset_resume[14315987.841029] hub 1-0:1.0: trying to enable port power on non-switchable hub[14315987.949971] usb usb2: usb resume[14315987.953634] ohci_hcd 0000:00:02.0: wakeup root hub[14315988.026616] hub 2-0:1.0: hub_reset_resume[14315988.031030] hub 2-0:1.0: trying to enable port power on non-switchable hub[14315988.139956] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC PPS CCS[14315988.159949] usb 2-1: finish reset-resume[14315988.419952] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS[14315988.479955] usb 2-1: reset low speed USB device using ohci_hcd and address 2[14315988.743285] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS[14315988.846616] usb 2-3: finish reset-resume[14315989.106618] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS[14315989.166618] usb 2-3: reset low speed USB device using ohci_hcd and address 3[14315989.433285] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS[14315989.516610] usb 2-3: manual set_interface for iface 0, alt 0[14315989.537646] usb 2-3: manual set_interface for iface 1, alt 0[14315989.554579] PM: Image restored successfully.[14315989.624012] Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000[14315989.635191] usb usb1: remote wakeup needed for autosuspend[14315989.639411] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0010[14315989.646085] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC PPS CCS[14315989.655410] hub 2-0:1.0: port 4, status 0101, change 0001, 12 Mb/s[14315989.734100] done.[14315989.737591] PM: Basic memory bitmaps freed[14315989.803290] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x101[14315989.916620] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315989.979960] usb 2-4: new full speed USB device using ohci_hcd and address 8[14315989.988178] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.002481] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.009944] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.126620] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315990.186620] usb 2-4: device descriptor read/64, error -62[14315990.294084] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.303277] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.303277] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.433285] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315990.493290] usb 2-4: device descriptor read/64, error -62[14315990.706618] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315990.769956] usb 2-4: new full speed USB device using ohci_hcd and address 9[14315990.780758] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.791297] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.804078] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315990.919953] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315990.979957] usb 2-4: device descriptor read/64, error -62[14315991.087264] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315991.096610] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315991.096614] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0in 5ec20000 cc 5 --> status -62[14315991.229953] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315991.289964] usb 2-4: device descriptor read/64, error -62[14315991.503285] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315991.566624] usb 2-4: new full speed USB device using ohci_hcd and address 10[14315991.577744] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0out 5ec20000 cc 5 --> status -62[14315991.790449] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0out 5ec20000 cc 5 --> status -62[14315992.003284] usb 2-4: device not accepting address 10, error -62[14315992.113285] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14315992.173291] usb 2-4: new full speed USB device using ohci_hcd and address 11[14315992.184180] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0out 5ec20000 cc 5 --> status -62[14315992.397242] ohci_hcd 0000:00:02.0: urb ffff810079c53680 path 4 ep0out 5ec20000 cc 5 --> status -62[14315992.609950] usb 2-4: device not accepting address 11, error -62[14315992.616293] hub 2-0:1.0: unable to enumerate USB device on port 4[14315992.626214] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0010[14315999.439944] [drm] Loading R300 Microcode[14316042.515071] PM: Hibernation mode set to 'platform'[14316042.526291] PM: Marking nosave pages: 000000000009f000 - 0000000000100000[14316042.536589] PM: Basic memory bitmaps created[14316042.538198] PM: Syncing filesystems ... done.[14316042.550112] Freezing user space processes ... (elapsed 0.00 seconds) done.[14316042.565534] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.[14316042.574058] PM: Shrinking memory... -done (0 pages freed)[14316042.771984] PM: Freed 0 kbytes in 0.19 seconds (0.00 MB/s)[14316042.779933] hub 2-0:1.0: hub_suspend[14316042.783880] usb usb2: bus suspend[14316042.789752] ohci_hcd 0000:00:02.0: suspend root hub[14316042.793447] hub 1-0:1.0: hub_suspend[14316042.797397] usb usb1: bus suspend[14316042.801079] ehci_hcd 0000:00:02.1: suspend root hub[14316042.806378] sd 0:0:0:0: [sda] Synchronizing SCSI cache[14316042.819280] ACPI: PCI interrupt for device 0000:01:08.0 disabled[14316042.825677] ACPI handle has no context![14316042.879962] ACPI: PCI interrupt for device 0000:00:06.1 disabled[14316042.899754] ACPI: PCI interrupt for device 0000:00:05.2 disabled[14316042.903324] ACPI: PCI interrupt for device 0000:00:05.1 disabled[14316042.909780] ACPI: PCI interrupt for device 0000:00:05.0 disabled[14316042.916204] ata8: port disabled. ignoring.[14316042.922637] ACPI: PCI interrupt for device 0000:00:02.1 disabled[14316042.929007] ehci_hcd 0000:00:02.1: --> no state change[14316042.932395] ACPI: PCI interrupt for device 0000:00:02.0 disabled[14316042.939043] ohci_hcd 0000:00:02.0: --> no state change[14316042.945692] ACPI: Preparing to enter system sleep state S4[14316042.952727] Extended CMOS year: 2000[14316042.953739] PM: Creating hibernation image: [14316042.953739] PM: Need to copy 82428 pages[14316042.953739] PM: Normal pages needed: 82428 + 1024 + 38, available pages: 441474[14316042.953739] PM: Hibernation image created (82428 pages copied)[14316042.953739] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[14316042.953739] svm_cpu_init: svm_data is NULL on 0[14316042.953739] Extended CMOS year: 2000[14316042.966088] ACPI: Unable to turn cooling device [ffff81007f842f50] 'off'[14316042.976587] ohci_hcd 0000:00:02.0: PCI legacy resume[14316042.979948] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14316042.989587] PCI: Setting latency timer of device 0000:00:02.0 to 64[14316042.996229] ohci_hcd 0000:00:02.0: powerup ports[14316043.022910] ehci_hcd 0000:00:02.1: PCI legacy resume[14316043.026611] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14316043.036198] PCI: Setting latency timer of device 0000:00:02.1 to 64[14316043.042853] PM: Writing back config space on device 0000:00:04.0 at offset 1 (was b00001, writing b00005)[14316043.052878] PCI: Setting latency timer of device 0000:00:04.0 to 64[14316043.062714] PM: Writing back config space on device 0000:00:05.0 at offset 1 (was b00003, writing b00007)[14316043.074451] ata8: port disabled. ignoring.[14316043.078822] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14316043.088715] PCI: Setting latency timer of device 0000:00:05.0 to 64[14316043.095744] PM: Writing back config space on device 0000:00:05.1 at offset 1 (was b00003, writing b00007)[14316043.105945] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14316043.113674] PCI: Setting latency timer of device 0000:00:05.1 to 64[14316043.123267] PM: Writing back config space on device 0000:00:05.2 at offset 1 (was b00003, writing b00007)[14316043.133264] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14316043.140088] PCI: Setting latency timer of device 0000:00:05.2 to 64[14316043.146850] PCI: Setting latency timer of device 0000:00:06.0 to 64[14316043.166620] PM: Writing back config space on device 0000:00:06.1 at offset f (was 5020200, writing 5020205)[14316043.176821] PM: Writing back config space on device 0000:00:06.1 at offset 4 (was 0, writing fe020000)[14316043.186581] PM: Writing back config space on device 0000:00:06.1 at offset 1 (was b00000, writing b00002)[14316043.199936] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 22[14316043.207524] PCI: Setting latency timer of device 0000:00:06.1 to 64[14316043.231202] ata7.01: ACPI cmd ef/03:44:00:00:00:b0 filtered out[14316043.236607] ata7.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out[14316043.243198] ata7: nv_mode_filter: 0x1f01f&0x1f01f->0x1f01f, BIOS=0x1f000 (0xc50000) ACPI=0x1f01f (600:30:0x1c)[14316043.266812] ata7.01: configured for UDMA/66[14316043.416621] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14316043.434478] ata2: SATA link down (SStatus 0 SControl 300)[14316043.453759] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14316043.460338] ata4: SATA link down (SStatus 0 SControl 300)[14316043.476354] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14316043.483008] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out[14316043.499809] ata6.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14316043.506447] ata5: SATA link down (SStatus 0 SControl 300)[14316043.513068] ata3: SATA link down (SStatus 0 SControl 300)[14316043.524158] ata6.00: configured for UDMA/100[14316043.528288] ata1.00: configured for UDMA/133[14316043.533090] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14316043.543053] sd 0:0:0:0: [sda] Write Protect is off[14316043.546928] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00[14316043.552768] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14316043.646619] PM: Writing back config space on device 0000:00:08.0 at offset f (was 14010100, writing 1401010a)[14316043.657001] PM: Writing back config space on device 0000:00:08.0 at offset 7 (was 0, writing fe028000)[14316043.666998] PM: Writing back config space on device 0000:00:08.0 at offset 6 (was 0, writing fe029000)[14316043.676541] PM: Writing back config space on device 0000:00:08.0 at offset 5 (was 1, writing b001)[14316043.686542] PM: Writing back config space on device 0000:00:08.0 at offset 4 (was 0, writing fe02a000)[14316043.695962] PM: Writing back config space on device 0000:00:08.0 at offset 1 (was b00000, writing b00007)[14316043.706310] eth0: no link during initialization.[14316043.723285] PM: Writing back config space on device 0000:00:09.0 at offset f (was 14010100, writing 1401010a)[14316043.733675] PM: Writing back config space on device 0000:00:09.0 at offset 7 (was 0, writing fe025000)[14316043.743671] PM: Writing back config space on device 0000:00:09.0 at offset 6 (was 0, writing fe026000)[14316043.753222] PM: Writing back config space on device 0000:00:09.0 at offset 5 (was 1, writing ac01)[14316043.763222] PM: Writing back config space on device 0000:00:09.0 at offset 4 (was 0, writing fe027000)[14316043.772644] PM: Writing back config space on device 0000:00:09.0 at offset 1 (was b00000, writing b00007)[14316043.785895] PCI: Setting latency timer of device 0000:00:0a.0 to 64[14316043.790896] PCI: Setting latency timer of device 0000:00:0e.0 to 64[14316043.809963] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18[14316043.828438] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16[14316043.838298] PCI: Setting latency timer of device 0000:02:00.0 to 64[14316043.843816] sd 0:0:0:0: [sda] Starting disk[14316043.858391] usb usb1: usb resume[14316043.918524] ehci_hcd 0000:00:02.1: resume root hub[14316043.986610] hub 1-0:1.0: hub_resume[14316043.990514] usb usb2: usb resume[14316043.994137] ohci_hcd 0000:00:02.0: resume root hub[14316044.066609] hub 2-0:1.0: hub_resume[14316044.070613] PM: writing image.[14316044.074110] PM: Free swap pages: 977947[14316044.079438] PM: Saving image data pages (82589 pages) ... 0% 1% 2% 3% 4% 5% 6% 7% 8% 9% 10% 11% 12% 13% 14% 15% 16% 17% 18% 19% 20% 21% 22% 23% 24% 25% 26% 27% 28% 29% 30% 31% 32% 33% 34% 35% 36% 37% 38% 39% 40% 41% 42% 43% 44% 45% 46% 47% 48% 49% 50% 51% 52% 53% 54% 55% 56% 57% 58% 59% 60% 61% 62% 63% 64% 65% 66% 67% 68% 69% 70% 71% 72% 73% 74% 75% 76% 77% 78% 79% 80% 81% 82% 83% 84% 85% 86% 87% 88% 89% 90% 91% 92% 93% 94% 95% 96% 97% 98% 99%100%done[14316048.280494] PM: Wrote 330356 kbytes in 4.19 seconds (78.84 MB/s)[14316048.287753] PM: S|[14316048.677728] ohci_hcd 0000:00:02.0: Unlink after no-IRQ? Controller is probably using the wrong IRQ.[14316048.692267] usb 2-3: usb suspend[14316048.714043] usb 2-1: usb suspend[14316048.729956] hub 2-0:1.0: hub_suspend[14316048.733955] usb usb2: bus suspend[14316048.737675] ohci_hcd 0000:00:02.0: suspend root hub[14316048.742965] hub 1-0:1.0: hub_suspend[14316048.749629] usb usb1: bus suspend[14316048.751176] ehci_hcd 0000:00:02.1: suspend root hub[14316048.755970] sd 0:0:0:0: [sda] Synchronizing SCSI cache[14316048.762812] sd 0:0:0:0: [sda] Stopping disk[14316049.190010] ACPI: PCI interrupt for device 0000:01:08.0 disabled[14316049.196537] ACPI handle has no context![14316049.253289] ACPI: PCI interrupt for device 0000:00:06.1 disabled[14316049.273115] ACPI: PCI interrupt for device 0000:00:05.2 disabled[14316049.289891] ACPI: PCI interrupt for device 0000:00:05.1 disabled[14316049.306511] ACPI: PCI interrupt for device 0000:00:05.0 disabled[14316049.323158] ata8: port disabled. ignoring.[14316049.337876] ACPI: PCI interrupt for device 0000:00:02.1 disabled[14316049.356406] ehci_hcd 0000:00:02.1: --> PCI D3/wakeup[14316049.358672] ACPI: PCI interrupt for device 0000:00:02.0 disabled[14316049.378443] ohci_hcd 0000:00:02.0: --> PCI D3/wakeup[14316049.382302] ACPI: Preparing to enter system sleep state S4[14316049.392357] Extended CMOS year: 2000[14316049.393306] hwsleep-0324 [03] enter_sleep_state : Entering sleep state [S4] [ 0.000000] Linux version 2.6.26-rc4 (ranma@melchior) (gcc version 4.2.3 (Debian 4.2.3-5)) #28 PREEMPT Sun Jun 1 09:06:24 CEST 2008[ 0.000000] Command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose console=ttyS0,115200 console=tty0 pci=nomsi no_console_suspend ro[ 0.000000] BIOS-provided physical RAM map:[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)[ 0.000000] BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)[ 0.000000] max_pfn_mapped = 1048576[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[ 0.000000] init_memory_mapping[ 0.000000] DMI 2.4 present.[ 0.000000] ACPI: RSDP 000F7D20, 0024 (r2 Nvidia)[ 0.000000] ACPI: XSDT 7FEE3100, 004C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: FACP 7FEEADC0, 00F4 (r3 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: DSDT 7FEE3280, 7ACE (r1 NVIDIA AWRDACPI 1000 MSFT 3000000)[ 0.000000] ACPI: FACS 7FEE0000, 0040[ 0.000000] ACPI: SSDT 7FEEB000, 0136 (r1 PTLTD POWERNOW 1 LTP 1)[ 0.000000] ACPI: HPET 7FEEB180, 0038 (r1 Nvidia ASUSACPI 42302E31 AWRD 98)[ 0.000000] ACPI: MCFG 7FEEB200, 003C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] ACPI: APIC 7FEEAF00, 0098 (r1 Nvidia ASUSACPI 42302E31 AWRD 0)[ 0.000000] early res: 0 [0-fff] BIOS data page[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE[ 0.000000] early res: 2 [200000-d3638f] TEXT DATA BSS[ 0.000000] early res: 3 [9f800-fffff] BIOS reserved[ 0.000000] early res: 4 [8000-bfff] PGTABLE[ 0.000000] Zone PFN ranges:[ 0.000000] DMA 0 -> 4096[ 0.000000] DMA32 4096 -> 1048576[ 0.000000] Normal 1048576 -> 1048576[ 0.000000] Movable zone start PFN for each node[ 0.000000] early_node_map[2] active PFN ranges[ 0.000000] 0: 0 -> 159[ 0.000000] 0: 256 -> 524000[ 0.000000] Detected use of extended apic ids on hypertransport bus[ 0.000000] ACPI: PM-Timer IO Port: 0x1008[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)[ 0.000000] Setting APIC routing to flat[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000[ 0.000000] Using ACPI (MADT) for SMP configuration information[ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000)[ 0.000000] mapped IOAPIC to ffffffffff5fa000 (00000000fec00000)[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)[14315324.233334] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 513763[14315324.233334] Kernel command line: root=/dev/sda5 resume=/dev/sda6 vga=6 apic=verbose console=ttyS0,115200 console=tty0 pci=nomsi no_console_suspend ro[14315324.233334] Initializing CPU#0[14315324.233334] PID hash table entries: 4096 (order: 12, 32768 bytes)[14315324.233334] Extended CMOS year: 2000[14315324.233334] TSC calibrated against PM_TIMER[14315324.233334] time.c: Detected 2411.099 MHz processor.[14315324.233334] Console: colour VGA+ 80x60[14315324.233334] console [tty0] enabled[14315324.233334] console [ttyS0] enabled[14315324.233334] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar[14315324.233334] ... MAX_LOCKDEP_SUBCLASSES: 8[14315324.233334] ... MAX_LOCK_DEPTH: 48[14315324.233334] ... MAX_LOCKDEP_KEYS: 2048[14315324.233334] ... CLASSHASH_SIZE: 1024[14315324.233334] ... MAX_LOCKDEP_ENTRIES: 8192[14315324.233334] ... MAX_LOCKDEP_CHAINS: 16384[14315324.233334] ... CHAINHASH_SIZE: 8192[14315324.233334] memory used by lock dependency info: 1648 kB[14315324.233334] per task-struct memory footprint: 2688 bytes[14315324.233334] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)[14315324.233334] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)[14315324.233334] Checking aperture...[14315324.233334] Node 0: aperture @ 89c000000 size 32 MB[14315324.233334] Aperture beyond 4GB. Ignoring.[14315324.233334] No AGP bridge found[14315324.233334] Memory: 2051692k/2096000k available (4624k kernel code, 43544k reserved, 2268k data, 260k init)[14315324.316528] Calibrating delay using timer specific routine.. 4827.00 BogoMIPS (lpj=8043205)[14315324.322857] Mount-cache hash table entries: 256[14315324.327216] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)[14315324.333327] CPU: L2 Cache: 512K (64 bytes/line)[14315324.336660] CPU: AMD Athlon(tm) 64 Processor 3800+ stepping 01[14315324.342949] ACPI: Core revision 20080321[14315324.359992] Parsing all Control Methods:[14315324.364011] Table [DSDT](id 0001) - 1203 Objects with 101 Devices 380 Methods 44 Regions[14315324.369992] Parsing all Control Methods:[14315324.373967] Table [SSDT](id 0002) - 4 Objects with 0 Devices 0 Methods 0 Regions[14315324.379991] tbxface-0598 [02] tb_load_namespace : ACPI Tables successfully acquired[14315324.389990] evxfevnt-0091 [02] enable : Transition to ACPI mode successful[14315324.398902] enabled ExtINT on CPU#0[14315324.402995] ENABLING IO-APIC IRQs[14315324.406656] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1[14315324.442963] Using local APIC timer interrupts.[14315324.449986] Detected 12.557 MHz APIC timer.[14315324.453320] net_namespace: 1272 bytes[14315324.456653] NET: Registered protocol family 16[14315324.460264] No dock devices found.[14315324.464193] TOM: 0000000080000000 aka 2048M[14315324.468794] ACPI: bus type pci registered[14315324.473293] PCI: Using configuration type 1 for base access[14315324.481638] evgpeblk-0956 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9[14315324.490697] evgpeblk-0956 [04] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9[14315324.509805] Completing Region/Field/Buffer/Package initialization:...................................................................................................................................................................................[14315324.545438] Initialized 39/44 Regions 11/11 Fields 40/40 Buffers 89/101 Packages (1216 nodes)[14315324.549980] Initializing Device/Processor/Thermal objects by executing _INI methods:...[14315324.556256] Executed 3 _INI methods requiring 1 _STA executions (examined 108 objects)[14315324.559979] evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 0 Runtime GPEs in this block[14315324.569979] evgpeblk-1052 [03] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 1 Runtime GPEs in this block[14315324.579978] ACPI: Interpreter enabled[14315324.583311] ACPI: (supports S0 S1 S3 S4 S5)[14315324.587956] ACPI: Using IOAPIC for interrupt routing[14315324.615461] ACPI: PCI Root Bridge [PCI0] (0000:00)[14315324.619975] PCI: Transparent bridge - 0000:00:06.0[14315324.713902] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.722705] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.728225] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 *10 11 14 15)[14315324.735728] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.741552] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.750170] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.758961] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)[14315324.763301] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.768606] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.777265] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)[14315324.784756] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)[14315324.792248] ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)[14315324.796634] ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)[14315324.800688] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.809481] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)[14315324.813830] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)[14315324.821293] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.[14315324.829952] ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)[14315324.834335] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)[14315324.841605] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)[14315324.849224] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.[14315324.853301] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.[14315324.857248] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0[14315324.863512] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.[14315324.870578] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.[14315324.877826] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.[14315324.885076] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0[14315324.889968] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.[14315324.895428] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0[14315324.899968] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0[14315324.903301] ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0[14315324.907248] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.[14315324.915381] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0[14315324.919968] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0[14315324.923301] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0[14315324.927248] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.[14315324.934992] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.[14315324.943228] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0[14315324.947246] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0[14315324.954299] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0[14315324.961381] Linux Plug and Play Support v0.97 (c) Adam Belay[14315324.966635] pnp: PnP ACPI init[14315324.969968] ACPI: bus type pnp registered[14315324.982451] pnp: PnP ACPI: found 13 devices[14315324.986635] ACPI: ACPI bus type pnp unregistered[14315324.989968] SCSI subsystem initialized[14315324.993332] usbcore: registered new interface driver usbfs[14315324.999240] usbcore: registered new interface driver hub[14315325.003301] usbcore: registered new device driver usb[14315325.006635] PCI: Using ACPI for IRQ routing[14315325.009968] testing the IO APIC.......................[14315325.013301] [14315325.013301] .................................... done.[14315325.027803] Bluetooth: Core ver 2.11[14315325.031935] NET: Registered protocol family 31[14315325.036635] Bluetooth: HCI device and connection manager initialized[14315325.039968] Bluetooth: HCI socket layer initialized[14315325.043301] DMAR:parse DMAR table failure.[14315325.054041] system 00:01: ioport range 0x1000-0x107f has been reserved[14315325.060937] system 00:01: ioport range 0x1080-0x10ff has been reserved[14315325.067822] system 00:01: ioport range 0x1400-0x147f has been reserved[14315325.074710] system 00:01: ioport range 0x1480-0x14ff has been reserved[14315325.081595] system 00:01: ioport range 0x1800-0x187f has been reserved[14315325.088483] system 00:01: ioport range 0x1880-0x18ff has been reserved[14315325.095381] system 00:02: ioport range 0x4d0-0x4d1 has been reserved[14315325.102093] system 00:02: ioport range 0x800-0x87f has been reserved[14315325.108807] system 00:02: ioport range 0x290-0x297 has been reserved[14315325.115543] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved[14315325.123491] system 00:0c: iomem range 0xcd000-0xcffff has been reserved[14315325.130464] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved[14315325.139923] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved[14315325.147328] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved[14315325.154735] system 00:0c: iomem range 0xfefff000-0xfefff0ff could not be reserved[14315325.162659] system 00:0c: iomem range 0x7fee0000-0x7fefffff could not be reserved[14315325.170116] system 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved[14315325.178043] system 00:0c: iomem range 0x0-0x9ffff could not be reserved[14315325.185017] system 00:0c: iomem range 0x100000-0x7fedffff could not be reserved[14315325.199647] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved[14315325.206708] system 00:0c: iomem range 0xfee00000-0xfeefffff could not be reserved[14315325.214634] system 00:0c: iomem range 0xfefff000-0xfeffffff could not be reserved[14315325.222585] system 00:0c: iomem range 0xfff80000-0xfff80fff could not be reserved[14315325.230510] system 00:0c: iomem range 0xfff90000-0xfffbffff could not be reserved[14315325.238441] system 00:0c: iomem range 0xfffed000-0xfffeffff could not be reserved[14315325.247394] PCI: Bridge: 0000:00:06.0[14315325.251018] IO window: 9000-9fff[14315325.254790] MEM window: disabled.[14315325.259831] PREFETCH window: disabled.[14315325.263697] PCI: Bridge: 0000:00:0a.0[14315325.267727] IO window: 8000-8fff[14315325.271501] MEM window: 0xfde00000-0xfdefffff[14315325.276395] PREFETCH window: 0x00000000e8000000-0x00000000efffffff[14315325.283110] PCI: Bridge: 0000:00:0e.0[14315325.287142] IO window: 6000-7fff[14315325.290913] MEM window: 0xfdd00000-0xfddfffff[14315325.295811] PREFETCH window: disabled.[14315325.300178] NET: Registered protocol family 2[14315325.335996] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)[14315325.344142] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)[14315325.353337] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)[14315325.365827] TCP: Hash tables configured (established 262144 bind 65536)[14315325.372834] TCP reno registered[14315325.385835] NET: Registered protocol family 1[14315325.392305] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).[14315325.399441] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.[14315325.405968] fuse init (API version 7.9)[14315325.410326] SGI XFS with security attributes, large block/inode numbers, no debug enabled[14315325.419254] msgmni has been set to 4007 for ipc namespace ffffffff808882f0[14315325.426697] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)[14315325.434550] io scheduler noop registered[14315325.439766] io scheduler anticipatory registered[14315325.444075] io scheduler deadline registered[14315325.449091] io scheduler cfq registered (default)[14315325.466344] pci 0000:00:05.0: Enabling HT MSI Mapping[14315325.471799] pci 0000:00:05.1: Enabling HT MSI Mapping[14315325.476916] pci 0000:00:05.2: Enabling HT MSI Mapping[14315325.482372] pci 0000:00:06.0: Enabling HT MSI Mapping[14315325.487809] pci 0000:00:06.1: Enabling HT MSI Mapping[14315325.493262] pci 0000:00:08.0: Enabling HT MSI Mapping[14315325.498703] pci 0000:00:09.0: Enabling HT MSI Mapping[14315325.504135] pci 0000:00:0a.0: Enabling HT MSI Mapping[14315325.509588] pci 0000:00:0e.0: Enabling HT MSI Mapping[14315325.515287] assign_interrupt_mode Found MSI capability[14315325.520606] assign_interrupt_mode Found MSI capability[14315325.526881] input: Power Button (FF) as /class/input/input0[14315325.532858] ACPI: Power Button (FF) [PWRF][14315325.537449] input: Power Button (CM) as /class/input/input1[14315325.543390] ACPI: Power Button (CM) [PWRB][14315325.549458] ACPI: PNP0C0B:00 is registered as cooling_device0[14315325.555580] ACPI: Fan [FAN] (on)[14315325.559460] ACPI: ACPI0007:00 is registered as cooling_device1[14315325.566720] ACPI: Expecting a [Reference] package element, found type 0[14315325.574102] ACPI: LNXTHERM:01 is registered as thermal_zone0[14315325.580563] ACPI: Thermal Zone [THRM] (40 C)[14315325.603595] Real Time Clock Driver v1.12ac[14315325.608075] Linux agpgart interface v0.103[14315325.612547] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled[14315325.622760] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A[14315325.630102] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A[14315325.637596] loop: module loaded[14315325.641032] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2[14315325.647514] e1000e: Copyright (c) 1999-2008 Intel Corporation.[14315325.653829] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI[14315325.660284] e100: Copyright(c) 1999-2006 Intel Corporation[14315325.666293] tun: Universal TUN/TAP device driver, 1.6[14315325.671712] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>[14315325.678480] Driver 'sd' needs updating - please use bus_type methods[14315325.685243] Driver 'sr' needs updating - please use bus_type methods[14315325.692949] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23[14315325.699077] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14315325.708827] sata_nv 0000:00:05.0: Using SWNCQ mode[14315325.714123] scsi0 : sata_nv[14315325.717541] scsi1 : sata_nv[14315325.721110] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 23[14315325.729217] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 23[14315326.206695] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14315326.220214] ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7[14315326.226587] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32)[14315326.240521] ata1.00: configured for UDMA/133[14315326.573691] ata2: SATA link down (SStatus 0 SControl 300)[14315326.592889] isa bounce pool size: 16 pages[14315326.596955] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5[14315326.606007] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315326.613434] sd 0:0:0:0: [sda] Write Protect is off[14315326.618637] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315326.627081] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14315326.636275] sd 0:0:0:0: [sda] Write Protect is off[14315326.640928] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14315326.650427] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >[14315326.740003] sd 0:0:0:0: [sda] Attached SCSI disk[14315326.748229] sd 0:0:0:0: Attached scsi generic sg0 type 0[14315326.755781] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22[14315326.761936] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14315326.772452] sata_nv 0000:00:05.1: Using SWNCQ mode[14315326.777683] scsi2 : sata_nv[14315326.781028] scsi3 : sata_nv[14315326.784603] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 22[14315326.792706] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 22[14315327.127025] ata3: SATA link down (SStatus 0 SControl 300)[14315327.473691] ata4: SATA link down (SStatus 0 SControl 300)[14315327.493337] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21[14315327.499341] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14315327.507738] sata_nv 0000:00:05.2: Using SWNCQ mode[14315327.513425] scsi4 : sata_nv[14315327.516781] scsi5 : sata_nv[14315327.520348] ata5: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xb400 irq 21[14315327.527925] ata6: SATA max UDMA/133 cmd 0xbc00 ctl 0xb800 bmdma 0xb408 irq 21[14315327.863749] ata5: SATA link down (SStatus 0 SControl 300)[14315328.353361] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14315328.383444] ata6.00: ATAPI: TSSTcorp CDDVDW SH-S203B, SB00, max UDMA/100[14315328.436778] ata6.00: configured for UDMA/100[14315328.476668] scsi 5:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S203B SB00 PQ: 0 ANSI: 5[14315328.600002] sr0: scsi3-mmc drive: 125x/48x writer dvd-ram cd/rw xa/form2 cdda tray[14315328.642296] Uniform CD-ROM driver Revision: 3.20[14315328.649446] sr 5:0:0:0: Attached scsi generic sg1 type 5[14315328.659784] block2mtd: version $Revision: 1.30 $[14315328.667052] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20[14315328.673194] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14315328.682802] ehci_hcd 0000:00:02.1: EHCI Host Controller[14315328.689317] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1[14315328.696829] ehci_hcd 0000:00:02.1: debug port 1[14315328.702248] ehci_hcd 0000:00:02.1: irq 20, io mem 0xfe02e000[14315328.716567] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004[14315328.723891] usb usb1: configuration #1 chosen from 1 choice[14315328.730025] hub 1-0:1.0: USB hub found[14315328.734185] hub 1-0:1.0: 10 ports detected[14315328.840224] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002[14315328.847386] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1[14315328.855061] usb usb1: Product: EHCI Host Controller[14315328.861727] usb usb1: Manufacturer: Linux 2.6.26-rc4 ehci_hcd[14315328.866980] usb usb1: SerialNumber: 0000:00:02.1[14315328.873993] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23[14315328.880101] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14315328.889364] ohci_hcd 0000:00:02.0: OHCI Host Controller[14315328.896669] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2[14315328.903383] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000[14315328.962374] usb usb2: configuration #1 chosen from 1 choice[14315328.968432] hub 2-0:1.0: USB hub found[14315328.972586] hub 2-0:1.0: 10 ports detected[14315329.050071] hub 1-0:1.0: unable to enumerate USB device on port 1[14315329.083321] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001[14315329.090008] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1[14315329.097286] usb usb2: Product: OHCI Host Controller[14315329.102530] usb usb2: Manufacturer: Linux 2.6.26-rc4 ohci_hcd[14315329.106885] usb usb2: SerialNumber: 0000:00:02.0[14315329.113130] USB Universal Host Controller Interface driver v3.0[14315329.253357] hub 1-0:1.0: unable to enumerate USB device on port 3[14315329.430023] hub 1-0:1.0: unable to enumerate USB device on port 4[14315329.436621] usbcore: registered new interface driver usblp[14315329.443451] PNP: No PS/2 controller found. Probing ports directly.[14315329.450472] serio: i8042 KBD port at 0x60,0x64 irq 1[14315329.456021] serio: i8042 AUX port at 0x60,0x64 irq 12[14315329.462037] mice: PS/2 mouse device common for all mice[14315329.486561] i2c /dev entries driver[14315329.490643] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00[14315329.496959] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40[14315329.503281] it87: Found IT8716F chip at 0x290, revision 0[14315329.507267] it87: in3 is VCC (+5V)[14315329.513179] it87: in7 is VCCH (+5V Stand-By)[14315329.543335] md: raid1 personality registered for level 1[14315329.550473] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx[14315329.559489] Bluetooth: HCI USB driver ver 2.9[14315329.716679] usb 2-1: new low speed USB device using ohci_hcd and address 2[14315329.903359] usb 2-1: configuration #1 chosen from 1 choice[14315329.926669] usb 2-1: New USB device found, idVendor=045e, idProduct=0040[14315329.933351] usb 2-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0[14315329.940927] usb 2-1: Product: Microsoft 3-Button Mouse with IntelliEye(TM)[14315329.949952] usb 2-1: Manufacturer: Microsoft[14315330.230013] usb 2-3: new low speed USB device using ohci_hcd and address 3[14315330.423345] usb 2-3: configuration #1 chosen from 1 choice[14315330.460003] usb 2-3: New USB device found, idVendor=045e, idProduct=00db[14315330.466683] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0[14315330.474261] usb 2-3: Product: Natural® Ergonomic Keyboard 4000[14315330.480453] usb 2-3: Manufacturer: Microsoft[14315330.763344] usb 2-4: new full speed USB device using ohci_hcd and address 4[14315330.936678] usb 2-4: device descriptor read/64, error -62[14315331.210011] usb 2-4: device descriptor read/64, error -62[14315331.476678] usb 2-4: new full speed USB device using ohci_hcd and address 5[14315331.650011] usb 2-4: device descriptor read/64, error -62[14315331.923344] usb 2-4: device descriptor read/64, error -62[14315332.190011] usb 2-4: new full speed USB device using ohci_hcd and address 6[14315332.603341] usb 2-4: device not accepting address 6, error -62[14315332.766677] usb 2-4: new full speed USB device using ohci_hcd and address 7[14315333.180008] usb 2-4: device not accepting address 7, error -62[14315333.186213] hub 2-0:1.0: unable to enumerate USB device on port 4[14315333.193008] usbcore: registered new interface driver hci_usb[14315333.199346] Bluetooth: HCI UART driver ver 2.2[14315333.205504] Bluetooth: HCI H4 protocol initialized[14315333.210322] Bluetooth: HCI BCSP protocol initialized[14315333.215671] cpuidle: using governor ladder[14315333.220135] cpuidle: using governor menu[14315333.230002] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2[14315333.261274] input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:02.0-1[14315333.280007] input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input3[14315333.314087] input: USB HID v1.11 Keyboard [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:02.0-3[14315333.336668] input: Microsoft Natural® Ergonomic Keyboard 4000 as /class/input/input4[14315333.370899] input: USB HID v1.11 Device [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:02.0-3[14315333.381147] usbcore: registered new interface driver usbhid[14315333.386945] usbhid: v2.6:USB HID core driver[14315333.393085] Advanced Linux Sound Architecture Driver Version 1.0.16.[14315333.400869] ALSA device list:[14315333.404208] No soundcards found.[14315333.408145] GACT probability on[14315333.411653] Mirror/redirect action on[14315333.416853] u32 classifier[14315333.419931] Performance counters on[14315333.421542] input device check on [14315333.425661] Actions configured [14315333.433116] IPv4 over IPv4 tunneling driver[14315333.437304] ip_tables: (C) 2000-2006 Netfilter Core Team[14315333.443091] TCP bic registered[14315333.446522] TCP cubic registered[14315333.450115] TCP westwood registered[14315333.453967] TCP htcp registered[14315333.457479] TCP vegas registered[14315333.461077] TCP yeah registered[14315333.464582] Initializing XFRM netlink socket[14315333.469529] NET: Registered protocol family 10[14315333.476669] IPv6 over IPv4 tunneling driver[14315333.483336] NET: Registered protocol family 17[14315333.490002] NET: Registered protocol family 15[14315333.493450] Bridge firewalling registered[14315333.497860] Bluetooth: L2CAP ver 2.9[14315333.501800] Bluetooth: L2CAP socket layer initialized[14315333.507218] Bluetooth: SCO (Voice Link) ver 0.5[14315333.512112] Bluetooth: SCO socket layer initialized[14315333.517037] Bluetooth: RFCOMM socket layer initialized[14315333.522549] Bluetooth: RFCOMM TTY layer initialized[14315333.527800] Bluetooth: RFCOMM ver 1.8[14315333.533062] Bluetooth: BNEP (Ethernet Emulation) ver 1.2[14315333.537101] Bluetooth: HIDP (Human Interface Emulation) ver 1.2[14315333.543695] RPC: Registered udp transport module.[14315333.549077] RPC: Registered tcp transport module.[14315333.554204] 802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>[14315333.562880] All bugs added by David S. Miller <davem@xxxxxxxxxx>[14315333.566792] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3800+ processors (1 cpu cores) (version 2.20.00)[14315333.579955] powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x8[14315333.583538] powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa[14315333.589709] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc[14315333.602320] powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe[14315333.608255] powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12[14315333.620496] Freezing user space processes ... (elapsed 0.00 seconds) done.[14315333.629026] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.[14315333.637034] PM: Loading image data pages (82589 pages) ... 0% 1% 2% 3% 4% 5% 6% 7% 8% 9% 10% 11% 12% 13% 14% 15% 16% 17% 18% 19% 20% 21% 22% 23% 24% 25% 26% 27% 28% 29% 30% 31%Marking TSC unstable due to cpufreq changes[14315335.330662] 32% 33% 34% 35% 36% 37% 38% 39% 40%<4>Clocksource tsc unstable (delta = -248506648 ns)[14315335.735245] 41% 42% 43% 44% 45% 46% 47% 48% 49% 50% 51% 52% 53% 54% 55% 56% 57% 58% 59% 60% 61% 62% 63% 64% 65% 66% 67% 68% 69% 70% 71% 72% 73% 74% 75% 76% 77% 78% 79% 80% 81% 82% 83% 84% 85% 86% 87% 88% 89% 90% 91% 92% 93% 94% 95% 96% 97% 98% 99%100%done[14315338.320334] PM: Read 330356 kbytes in 4.68 seconds (70.58 MB/s)[14315338.341762] sd 0:0:0:0: [sda] Synchronizing SCSI cache[14315338.350008] ACPI: PCI interrupt for device 0000:00:05.2 disabled[14315338.354161] ACPI: PCI interrupt for device 0000:00:05.1 disabled[14315338.360826] ACPI: PCI interrupt for device 0000:00:05.0 disabled[14315338.367267] ACPI: PCI interrupt for device 0000:00:02.0 disabled[14315338.373860] Extended CMOS year: 2000[14316042.953739] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106[14316042.953739] evxfevnt-0079 [02] enable : System is already in ACPI mode[14316042.953739] svm_cpu_init: svm_data is NULL on 0[14316042.953739] Extended CMOS year: 2000[14316042.978446] ACPI: Unable to turn cooling device [ffff81007f842f50] 'off'[14316042.985081] ohci_hcd 0000:00:02.0: PCI legacy resume[14316042.991683] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23[14316043.000127] PCI: Setting latency timer of device 0000:00:02.0 to 64[14316043.006555] ohci_hcd 0000:00:02.0: lost power[14316043.067239] ohci_hcd 0000:00:02.0: OHCI controller state[14316043.073837] ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers[14316043.080939] ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3[14316043.088830] ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0[14316043.095497] ohci_hcd 0000:00:02.0: intrstatus 0x00000044 RHSC SF[14316043.101379] ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH[14316043.107788] ohci_hcd 0000:00:02.0: hcca frame #002d[14316043.113060] ohci_hcd 0000:00:02.0: roothub.a 0100120a POTPGT=1 NOCP NPS NDP=10(10)[14316043.123059] ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000[14316043.128132] ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE[14316043.134800] ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS[14316043.142770] ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS[14316043.149876] ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00010301 CSC LSDA PPS CCS[14316043.159876] ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00010101 CSC PPS CCS[14316043.166081] ohci_hcd 0000:00:02.0: roothub.portstatus [4] 0x00000100 PPS[14316043.173177] ohci_hcd 0000:00:02.0: roothub.portstatus [5] 0x00000100 PPS[14316043.183177] ohci_hcd 0000:00:02.0: roothub.portstatus [6] 0x00000100 PPS[14316043.187374] ohci_hcd 0000:00:02.0: roothub.portstatus [7] 0x00000100 PPS[14316043.194471] ohci_hcd 0000:00:02.0: roothub.portstatus [8] 0x00000100 PPS[14316043.201571] ohci_hcd 0000:00:02.0: roothub.portstatus [9] 0x00000100 PPS[14316043.208667] ohci_hcd 0000:00:02.0: restart complete[14316043.215334] usb usb2: root hub lost power or was reset[14316043.219485] ohci_hcd 0000:00:02.0: suspend root hub[14316043.226154] ehci_hcd 0000:00:02.1: PCI legacy resume[14316043.231435] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20[14316043.239441] PCI: Setting latency timer of device 0000:00:02.1 to 64[14316043.246120] ehci_hcd 0000:00:02.1: lost power, restarting[14316043.252770] usb usb1: root hub lost power or was reset[14316043.258599] ehci_hcd 0000:00:02.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT[14316043.267470] ehci_hcd 0000:00:02.1: debug port 1[14316043.271595] PCI: cache line size of 64 is not supported by device 0000:00:02.1[14316043.279323] PCI: Setting latency timer of device 0000:00:04.0 to 64[14316043.294538] ata8: port disabled. ignoring.[14316043.300828] PM: Writing back config space on device 0000:00:05.0 at offset 1 (was b00003, writing b00007)[14316043.310929] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 23[14316043.320659] PCI: Setting latency timer of device 0000:00:05.0 to 64[14316043.327303] PM: Writing back config space on device 0000:00:05.1 at offset 1 (was b00003, writing b00007)[14316043.338069] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 22[14316043.347650] PCI: Setting latency timer of device 0000:00:05.1 to 64[14316043.354561] PM: Writing back config space on device 0000:00:05.2 at offset 1 (was b00003, writing b00007)[14316043.365135] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 21[14316043.374686] PCI: Setting latency timer of device 0000:00:05.2 to 64[14316043.381567] PCI: Setting latency timer of device 0000:00:06.0 to 64[14316043.399958] PM: Writing back config space on device 0000:00:06.1 at offset 1 (was b00006, writing b00002)[14316043.410047] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 22[14316043.419357] PCI: Setting latency timer of device 0000:00:06.1 to 64[14316043.475393] ata7.01: ACPI cmd ef/03:44:00:00:00:b0 filtered out[14316043.479959] ata7.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out[14316043.486295] ata7: nv_mode_filter: 0x1f01f&0x1f01f->0x1f01f, BIOS=0x1f000 (0xc50000) ACPI=0x1f01f (600:30:0x1c)[14316043.503603] ata7.01: configured for UDMA/66[14316043.649959] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)[14316043.705849] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[14316043.761923] ata2: SATA link down (SStatus 0 SControl 300)[14316043.768607] ata6.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14316043.774862] ata4: SATA link down (SStatus 0 SControl 300)[14316043.781536] ata3: SATA link down (SStatus 0 SControl 300)[14316043.787696] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out[14316043.793812] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out[14316043.800465] ata6.00: configured for UDMA/100[14316043.805232] ata5: SATA link down (SStatus 0 SControl 300)[14316043.811777] ata1.00: configured for UDMA/133[14316043.819807] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)[14316043.824302] sd 0:0:0:0: [sda] Write Protect is off[14316043.829585] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00[14316043.836316] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA[14316043.870403] eth0: no link during initialization.[14316043.887365] PCI: Setting latency timer of device 0000:00:0a.0 to 64[14316043.895115] PCI: Setting latency timer of device 0000:00:0e.0 to 64[14316043.913287] PM: Writing back config space on device 0000:01:08.0 at offset 1 (was 2900005, writing 2900001)[14316043.923545] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18[14316043.941120] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 16[14316043.952082] PCI: Setting latency timer of device 0000:02:00.0 to 64[14316043.958846] sd 0:0:0:0: [sda] Starting disk[14316043.969848] usb usb1: usb resume[14316043.977995] ehci_hcd 0000:00:02.1: resume root hub after power loss[14316044.073278] ehci_hcd 0000:00:02.1: port 4 low speed --> companion[14316044.079790] ehci_hcd 0000:00:02.1: port 3 low speed --> companion[14316044.086449] ehci_hcd 0000:00:02.1: port 1 low speed --> companion[14316044.183280] ehci_hcd 0000:00:02.1: GetStatus port 4 status 003402 POWER OWNER sig=k CSC[14316044.198098] ehci_hcd 0000:00:02.1: GetStatus port 3 status 003402 POWER OWNER sig=k CSC[14316044.208097] ehci_hcd 0000:00:02.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC[14316044.226611] hub 1-0:1.0: hub_reset_resume[14316044.231026] hub 1-0:1.0: trying to enable port power on non-switchable hub[14316044.339965] usb usb2: usb resume[14316044.343635] ohci_hcd 0000:00:02.0: wakeup root hub[14316044.416610] hub 2-0:1.0: hub_reset_resume[14316044.421024] hub 2-0:1.0: trying to enable port power on non-switchable hub[14316044.529951] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC PPS CCS[14316044.549943] usb 2-1: finish reset-resume[14316044.809946] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS[14316044.869949] usb 2-1: reset low speed USB device using ohci_hcd and address 2[14316045.133279] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS[14316045.236610] usb 2-3: finish reset-resume[14316045.496612] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS[14316045.556612] usb 2-3: reset low speed USB device using ohci_hcd and address 3[14316045.823279] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [2] = 0x00100303 PRSC LSDA PPS PES CCS[14316045.904597] usb 2-3: manual set_interface for iface 0, alt 0[14316045.927640] usb 2-3: manual set_interface for iface 1, alt 0[14316045.939040] PM: Image restored successfully.[14316046.137987] Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000[14316046.148422] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0010[14316046.155074] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC PPS CCS[14316046.164442] hub 2-0:1.0: port 4, status 0101, change 0001, 12 Mb/s[14316046.257296] done.[14316046.267195] PM: Basic memory bitmaps freed[14316046.293285] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x101[14316046.406614] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316046.469949] usb 2-4: new full speed USB device using ohci_hcd and address 12[14316046.480843] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316046.491303] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316046.504082] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316046.619948] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316046.679951] usb 2-4: device descriptor read/64, error -62[14316046.787270] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316046.796604] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316046.796608] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316046.926614] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316046.986619] usb 2-4: device descriptor read/64, error -62[14316047.199946] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316047.263284] usb 2-4: new full speed USB device using ohci_hcd and address 13[14316047.271820] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316047.284069] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316047.293272] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316047.413281] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316047.476614] usb 2-4: device descriptor read/64, error -62[14316047.584063] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316047.593272] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316047.593275] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0in 5ec20000 cc 5 --> status -62[14316047.726613] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316047.786618] usb 2-4: device descriptor read/64, error -62[14316047.999946] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316048.063282] usb 2-4: new full speed USB device using ohci_hcd and address 14[14316048.074171] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0out 5ec20000 cc 5 --> status -62[14316048.287247] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0out 5ec20000 cc 5 --> status -62[14316048.499945] usb 2-4: device not accepting address 14, error -62[14316048.609947] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS[14316048.669950] usb 2-4: new full speed USB device using ohci_hcd and address 15[14316048.680847] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0out 5ec20000 cc 5 --> status -62[14316048.894040] ohci_hcd 0000:00:02.0: urb ffff810079c53080 path 4 ep0out 5ec20000 cc 5 --> status -62[14316049.106612] usb 2-4: device not accepting address 15, error -62[14316049.112960] hub 2-0:1.0: unable to enumerate USB device on port 4[14316049.119635] hub 1-0:1.0: hub_suspend[14316049.126148] usb usb1: bus auto-suspend[14316049.127875] ehci_hcd 0000:00:02.1: suspend root hub[14316049.137334] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0010[14316054.935949] [drm] Loading R300 Microcode[14316192.574403] usb usb1: usb auto-resume[14316192.579981] ehci_hcd 0000:00:02.1: resume root hub[14316192.686598] hub 1-0:1.0: hub_resume[14316192.690414] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0000[14316194.696600] hub 1-0:1.0: hub_suspend[14316194.700479] usb usb1: bus auto-suspend[14316194.704516] ehci_hcd 0000:00:02.1: suspend root hub
Kernel config:## Automatically generated make config: don't edit# Linux kernel version: 2.6.26-rc4# Sun Jun 1 09:04:00 2008#CONFIG_64BIT=y# CONFIG_X86_32 is not setCONFIG_X86_64=yCONFIG_X86=yCONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig"# CONFIG_GENERIC_LOCKBREAK is not setCONFIG_GENERIC_TIME=yCONFIG_GENERIC_CMOS_UPDATE=yCONFIG_CLOCKSOURCE_WATCHDOG=yCONFIG_GENERIC_CLOCKEVENTS=yCONFIG_GENERIC_CLOCKEVENTS_BROADCAST=yCONFIG_LOCKDEP_SUPPORT=yCONFIG_STACKTRACE_SUPPORT=yCONFIG_HAVE_LATENCYTOP_SUPPORT=yCONFIG_FAST_CMPXCHG_LOCAL=yCONFIG_MMU=yCONFIG_ZONE_DMA=yCONFIG_GENERIC_ISA_DMA=yCONFIG_GENERIC_IOMAP=yCONFIG_GENERIC_BUG=yCONFIG_GENERIC_HWEIGHT=y# CONFIG_GENERIC_GPIO is not setCONFIG_ARCH_MAY_HAVE_PC_FDC=yCONFIG_RWSEM_GENERIC_SPINLOCK=y# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set# CONFIG_ARCH_HAS_ILOG2_U32 is not set# CONFIG_ARCH_HAS_ILOG2_U64 is not setCONFIG_ARCH_HAS_CPU_IDLE_WAIT=yCONFIG_GENERIC_CALIBRATE_DELAY=yCONFIG_GENERIC_TIME_VSYSCALL=yCONFIG_ARCH_HAS_CPU_RELAX=yCONFIG_ARCH_HAS_CACHE_LINE_SIZE=yCONFIG_HAVE_SETUP_PER_CPU_AREA=y# CONFIG_HAVE_CPUMASK_OF_CPU_MAP is not setCONFIG_ARCH_HIBERNATION_POSSIBLE=yCONFIG_ARCH_SUSPEND_POSSIBLE=yCONFIG_ZONE_DMA32=yCONFIG_ARCH_POPULATES_NODE_MAP=yCONFIG_AUDIT_ARCH=yCONFIG_ARCH_SUPPORTS_AOUT=yCONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=yCONFIG_GENERIC_HARDIRQS=yCONFIG_GENERIC_IRQ_PROBE=yCONFIG_X86_BIOS_REBOOT=yCONFIG_X86_TRAMPOLINE=y# CONFIG_KTIME_SCALAR is not setCONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
## General setup#CONFIG_EXPERIMENTAL=yCONFIG_BROKEN_ON_SMP=yCONFIG_LOCK_KERNEL=yCONFIG_INIT_ENV_ARG_LIMIT=32CONFIG_LOCALVERSION=""CONFIG_LOCALVERSION_AUTO=yCONFIG_SWAP=yCONFIG_SYSVIPC=yCONFIG_SYSVIPC_SYSCTL=y# CONFIG_POSIX_MQUEUE is not setCONFIG_BSD_PROCESS_ACCT=yCONFIG_BSD_PROCESS_ACCT_V3=y# CONFIG_TASKSTATS is not set# CONFIG_AUDIT is not setCONFIG_IKCONFIG=yCONFIG_IKCONFIG_PROC=yCONFIG_LOG_BUF_SHIFT=16# CONFIG_CGROUPS is not setCONFIG_HAVE_UNSTABLE_SCHED_CLOCK=yCONFIG_GROUP_SCHED=yCONFIG_FAIR_GROUP_SCHED=y# CONFIG_RT_GROUP_SCHED is not setCONFIG_USER_SCHED=y# CONFIG_CGROUP_SCHED is not setCONFIG_SYSFS_DEPRECATED=yCONFIG_SYSFS_DEPRECATED_V2=y# CONFIG_RELAY is not set# CONFIG_NAMESPACES is not set# CONFIG_BLK_DEV_INITRD is not setCONFIG_CC_OPTIMIZE_FOR_SIZE=yCONFIG_SYSCTL=yCONFIG_EMBEDDED=yCONFIG_UID16=yCONFIG_SYSCTL_SYSCALL=yCONFIG_SYSCTL_SYSCALL_CHECK=yCONFIG_KALLSYMS=yCONFIG_KALLSYMS_ALL=y# CONFIG_KALLSYMS_EXTRA_PASS is not setCONFIG_HOTPLUG=yCONFIG_PRINTK=yCONFIG_BUG=yCONFIG_ELF_CORE=yCONFIG_PCSPKR_PLATFORM=y# CONFIG_COMPAT_BRK is not setCONFIG_BASE_FULL=yCONFIG_FUTEX=yCONFIG_ANON_INODES=yCONFIG_EPOLL=yCONFIG_SIGNALFD=yCONFIG_TIMERFD=yCONFIG_EVENTFD=yCONFIG_SHMEM=yCONFIG_VM_EVENT_COUNTERS=yCONFIG_SLAB=y# CONFIG_SLUB is not set# CONFIG_SLOB is not set# CONFIG_PROFILING is not set# CONFIG_MARKERS is not setCONFIG_HAVE_OPROFILE=y# CONFIG_KPROBES is not setCONFIG_HAVE_KPROBES=yCONFIG_HAVE_KRETPROBES=y# CONFIG_HAVE_DMA_ATTRS is not setCONFIG_PROC_PAGE_MONITOR=yCONFIG_SLABINFO=yCONFIG_RT_MUTEXES=y# CONFIG_TINY_SHMEM is not setCONFIG_BASE_SMALL=0CONFIG_MODULES=y# CONFIG_MODULE_FORCE_LOAD is not setCONFIG_MODULE_UNLOAD=yCONFIG_MODULE_FORCE_UNLOAD=y# CONFIG_MODVERSIONS is not set# CONFIG_MODULE_SRCVERSION_ALL is not setCONFIG_KMOD=yCONFIG_BLOCK=y# CONFIG_BLK_DEV_IO_TRACE is not setCONFIG_BLK_DEV_BSG=yCONFIG_BLOCK_COMPAT=y
## IO Schedulers#CONFIG_IOSCHED_NOOP=yCONFIG_IOSCHED_AS=yCONFIG_IOSCHED_DEADLINE=yCONFIG_IOSCHED_CFQ=y# CONFIG_DEFAULT_AS is not set# CONFIG_DEFAULT_DEADLINE is not setCONFIG_DEFAULT_CFQ=y# CONFIG_DEFAULT_NOOP is not setCONFIG_DEFAULT_IOSCHED="cfq"CONFIG_PREEMPT_NOTIFIERS=yCONFIG_CLASSIC_RCU=y
## Processor type and features#CONFIG_TICK_ONESHOT=yCONFIG_NO_HZ=yCONFIG_HIGH_RES_TIMERS=yCONFIG_GENERIC_CLOCKEVENTS_BUILD=y# CONFIG_SMP is not setCONFIG_X86_PC=y# CONFIG_X86_ELAN is not set# CONFIG_X86_VOYAGER is not set# CONFIG_X86_NUMAQ is not set# CONFIG_X86_SUMMIT is not set# CONFIG_X86_BIGSMP is not set# CONFIG_X86_VISWS is not set# CONFIG_X86_GENERICARCH is not set# CONFIG_X86_ES7000 is not set# CONFIG_X86_RDC321X is not set# CONFIG_X86_VSMP is not set# CONFIG_PARAVIRT_GUEST is not setCONFIG_MEMTEST_BOOTPARAM=yCONFIG_MEMTEST_BOOTPARAM_VALUE=0# CONFIG_M386 is not set# CONFIG_M486 is not set# CONFIG_M586 is not set# CONFIG_M586TSC is not set# CONFIG_M586MMX is not set# CONFIG_M686 is not set# CONFIG_MPENTIUMII is not set# CONFIG_MPENTIUMIII is not set# CONFIG_MPENTIUMM is not set# CONFIG_MPENTIUM4 is not set# CONFIG_MK6 is not set# CONFIG_MK7 is not setCONFIG_MK8=y# CONFIG_MCRUSOE is not set# CONFIG_MEFFICEON is not set# CONFIG_MWINCHIPC6 is not set# CONFIG_MWINCHIP2 is not set# CONFIG_MWINCHIP3D is not set# CONFIG_MGEODEGX1 is not set# CONFIG_MGEODE_LX is not set# CONFIG_MCYRIXIII is not set# CONFIG_MVIAC3_2 is not set# CONFIG_MVIAC7 is not set# CONFIG_MPSC is not set# CONFIG_MCORE2 is not set# CONFIG_GENERIC_CPU is not setCONFIG_X86_CPU=yCONFIG_X86_L1_CACHE_BYTES=64CONFIG_X86_INTERNODE_CACHE_BYTES=64CONFIG_X86_CMPXCHG=yCONFIG_X86_L1_CACHE_SHIFT=6CONFIG_X86_GOOD_APIC=yCONFIG_X86_INTEL_USERCOPY=yCONFIG_X86_USE_PPRO_CHECKSUM=yCONFIG_X86_TSC=yCONFIG_X86_CMOV=yCONFIG_X86_MINIMUM_CPU_FAMILY=64CONFIG_X86_DEBUGCTLMSR=yCONFIG_HPET_TIMER=yCONFIG_HPET_EMULATE_RTC=yCONFIG_DMI=yCONFIG_GART_IOMMU=y# CONFIG_CALGARY_IOMMU is not setCONFIG_SWIOTLB=yCONFIG_IOMMU_HELPER=y# CONFIG_PREEMPT_NONE is not set# CONFIG_PREEMPT_VOLUNTARY is not setCONFIG_PREEMPT=y# CONFIG_PREEMPT_RCU is not setCONFIG_X86_LOCAL_APIC=yCONFIG_X86_IO_APIC=yCONFIG_X86_MCE=y# CONFIG_X86_MCE_INTEL is not setCONFIG_X86_MCE_AMD=y# CONFIG_I8K is not set# CONFIG_MICROCODE is not set# CONFIG_X86_MSR is not set# CONFIG_X86_CPUID is not setCONFIG_ARCH_SPARSEMEM_DEFAULT=yCONFIG_ARCH_SPARSEMEM_ENABLE=yCONFIG_ARCH_SELECT_MEMORY_MODEL=yCONFIG_SELECT_MEMORY_MODEL=y# CONFIG_FLATMEM_MANUAL is not set# CONFIG_DISCONTIGMEM_MANUAL is not setCONFIG_SPARSEMEM_MANUAL=yCONFIG_SPARSEMEM=yCONFIG_HAVE_MEMORY_PRESENT=y# CONFIG_SPARSEMEM_STATIC is not setCONFIG_SPARSEMEM_EXTREME=yCONFIG_SPARSEMEM_VMEMMAP_ENABLE=yCONFIG_SPARSEMEM_VMEMMAP=y
## Memory hotplug is currently incompatible with Software Suspend#CONFIG_PAGEFLAGS_EXTENDED=yCONFIG_SPLIT_PTLOCK_CPUS=4CONFIG_RESOURCES_64BIT=yCONFIG_ZONE_DMA_FLAG=1CONFIG_BOUNCE=yCONFIG_VIRT_TO_BUS=yCONFIG_MTRR=yCONFIG_X86_PAT=y# CONFIG_EFI is not set# CONFIG_SECCOMP is not set# CONFIG_HZ_100 is not set# CONFIG_HZ_250 is not setCONFIG_HZ_300=y# CONFIG_HZ_1000 is not setCONFIG_HZ=300CONFIG_SCHED_HRTICK=yCONFIG_KEXEC=y# CONFIG_CRASH_DUMP is not setCONFIG_PHYSICAL_START=0x200000# CONFIG_RELOCATABLE is not setCONFIG_PHYSICAL_ALIGN=0x200000CONFIG_COMPAT_VDSO=yCONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
## Power management options#CONFIG_ARCH_HIBERNATION_HEADER=yCONFIG_PM=yCONFIG_PM_DEBUG=y# CONFIG_PM_VERBOSE is not setCONFIG_CAN_PM_TRACE=y# CONFIG_PM_TRACE_RTC is not setCONFIG_PM_SLEEP=yCONFIG_SUSPEND=yCONFIG_SUSPEND_FREEZER=yCONFIG_HIBERNATION=yCONFIG_PM_STD_PARTITION=""CONFIG_ACPI=yCONFIG_ACPI_SLEEP=yCONFIG_ACPI_PROCFS=yCONFIG_ACPI_PROCFS_POWER=yCONFIG_ACPI_SYSFS_POWER=yCONFIG_ACPI_PROC_EVENT=yCONFIG_ACPI_AC=y# CONFIG_ACPI_BATTERY is not setCONFIG_ACPI_BUTTON=yCONFIG_ACPI_FAN=yCONFIG_ACPI_DOCK=y# CONFIG_ACPI_BAY is not setCONFIG_ACPI_PROCESSOR=yCONFIG_ACPI_THERMAL=y# CONFIG_ACPI_WMI is not set# CONFIG_ACPI_ASUS is not set# CONFIG_ACPI_TOSHIBA is not setCONFIG_ACPI_CUSTOM_DSDT_FILE=""# CONFIG_ACPI_CUSTOM_DSDT is not setCONFIG_ACPI_BLACKLIST_YEAR=0CONFIG_ACPI_DEBUG=yCONFIG_ACPI_DEBUG_FUNC_TRACE=yCONFIG_ACPI_EC=yCONFIG_ACPI_POWER=yCONFIG_ACPI_SYSTEM=yCONFIG_X86_PM_TIMER=y# CONFIG_ACPI_CONTAINER is not set# CONFIG_ACPI_SBS is not set
## CPU Frequency scaling#CONFIG_CPU_FREQ=yCONFIG_CPU_FREQ_TABLE=y# CONFIG_CPU_FREQ_DEBUG is not setCONFIG_CPU_FREQ_STAT=y# CONFIG_CPU_FREQ_STAT_DETAILS is not set# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not setCONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not setCONFIG_CPU_FREQ_GOV_PERFORMANCE=yCONFIG_CPU_FREQ_GOV_POWERSAVE=yCONFIG_CPU_FREQ_GOV_USERSPACE=yCONFIG_CPU_FREQ_GOV_ONDEMAND=yCONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
## CPUFreq processor drivers## CONFIG_X86_ACPI_CPUFREQ is not setCONFIG_X86_POWERNOW_K8=yCONFIG_X86_POWERNOW_K8_ACPI=y# CONFIG_X86_SPEEDSTEP_CENTRINO is not set# CONFIG_X86_P4_CLOCKMOD is not set
## shared options## CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set# CONFIG_X86_SPEEDSTEP_LIB is not setCONFIG_CPU_IDLE=yCONFIG_CPU_IDLE_GOV_LADDER=yCONFIG_CPU_IDLE_GOV_MENU=y
## Bus options (PCI etc.)#CONFIG_PCI=yCONFIG_PCI_DIRECT=y# CONFIG_PCI_MMCONFIG is not setCONFIG_PCI_DOMAINS=yCONFIG_DMAR=yCONFIG_DMAR_GFX_WA=yCONFIG_DMAR_FLOPPY_WA=yCONFIG_PCIEPORTBUS=yCONFIG_PCIEAER=yCONFIG_PCIEASPM=yCONFIG_PCIEASPM_DEBUG=yCONFIG_ARCH_SUPPORTS_MSI=yCONFIG_PCI_MSI=yCONFIG_PCI_LEGACY=y# CONFIG_PCI_DEBUG is not setCONFIG_HT_IRQ=yCONFIG_ISA_DMA_API=yCONFIG_K8_NB=y# CONFIG_PCCARD is not set# CONFIG_HOTPLUG_PCI is not set
## Executable file formats / Emulations#CONFIG_BINFMT_ELF=yCONFIG_COMPAT_BINFMT_ELF=yCONFIG_BINFMT_MISC=yCONFIG_IA32_EMULATION=y# CONFIG_IA32_AOUT is not setCONFIG_COMPAT=yCONFIG_COMPAT_FOR_U64_ALIGNMENT=yCONFIG_SYSVIPC_COMPAT=y
## Networking#CONFIG_NET=y
## Networking options#CONFIG_PACKET=yCONFIG_PACKET_MMAP=yCONFIG_UNIX=yCONFIG_XFRM=yCONFIG_XFRM_USER=y# CONFIG_XFRM_SUB_POLICY is not set# CONFIG_XFRM_MIGRATE is not set# CONFIG_XFRM_STATISTICS is not setCONFIG_NET_KEY=y# CONFIG_NET_KEY_MIGRATE is not setCONFIG_INET=yCONFIG_IP_MULTICAST=yCONFIG_IP_ADVANCED_ROUTER=yCONFIG_ASK_IP_FIB_HASH=y# CONFIG_IP_FIB_TRIE is not setCONFIG_IP_FIB_HASH=yCONFIG_IP_MULTIPLE_TABLES=yCONFIG_IP_ROUTE_MULTIPATH=yCONFIG_IP_ROUTE_VERBOSE=y# CONFIG_IP_PNP is not setCONFIG_NET_IPIP=y# CONFIG_NET_IPGRE is not setCONFIG_IP_MROUTE=yCONFIG_IP_PIMSM_V1=yCONFIG_IP_PIMSM_V2=y# CONFIG_ARPD is not setCONFIG_SYN_COOKIES=yCONFIG_INET_AH=yCONFIG_INET_ESP=yCONFIG_INET_IPCOMP=yCONFIG_INET_XFRM_TUNNEL=yCONFIG_INET_TUNNEL=yCONFIG_INET_XFRM_MODE_TRANSPORT=yCONFIG_INET_XFRM_MODE_TUNNEL=yCONFIG_INET_XFRM_MODE_BEET=yCONFIG_INET_LRO=yCONFIG_INET_DIAG=yCONFIG_INET_TCP_DIAG=yCONFIG_TCP_CONG_ADVANCED=yCONFIG_TCP_CONG_BIC=yCONFIG_TCP_CONG_CUBIC=yCONFIG_TCP_CONG_WESTWOOD=yCONFIG_TCP_CONG_HTCP=y# CONFIG_TCP_CONG_HSTCP is not set# CONFIG_TCP_CONG_HYBLA is not setCONFIG_TCP_CONG_VEGAS=y# CONFIG_TCP_CONG_SCALABLE is not set# CONFIG_TCP_CONG_LP is not set# CONFIG_TCP_CONG_VENO is not setCONFIG_TCP_CONG_YEAH=y# CONFIG_TCP_CONG_ILLINOIS is not set# CONFIG_DEFAULT_BIC is not setCONFIG_DEFAULT_CUBIC=y# CONFIG_DEFAULT_HTCP is not set# CONFIG_DEFAULT_VEGAS is not set# CONFIG_DEFAULT_WESTWOOD is not set# CONFIG_DEFAULT_RENO is not setCONFIG_DEFAULT_TCP_CONG="cubic"# CONFIG_TCP_MD5SIG is not set# CONFIG_IP_VS is not setCONFIG_IPV6=y# CONFIG_IPV6_PRIVACY is not set# CONFIG_IPV6_ROUTER_PREF is not set# CONFIG_IPV6_OPTIMISTIC_DAD is not setCONFIG_INET6_AH=yCONFIG_INET6_ESP=yCONFIG_INET6_IPCOMP=y# CONFIG_IPV6_MIP6 is not setCONFIG_INET6_XFRM_TUNNEL=yCONFIG_INET6_TUNNEL=yCONFIG_INET6_XFRM_MODE_TRANSPORT=yCONFIG_INET6_XFRM_MODE_TUNNEL=yCONFIG_INET6_XFRM_MODE_BEET=y# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not setCONFIG_IPV6_SIT=yCONFIG_IPV6_NDISC_NODETYPE=yCONFIG_IPV6_TUNNEL=y# CONFIG_IPV6_MULTIPLE_TABLES is not setCONFIG_IPV6_MROUTE=yCONFIG_IPV6_PIMSM_V2=y# CONFIG_NETWORK_SECMARK is not setCONFIG_NETFILTER=y# CONFIG_NETFILTER_DEBUG is not setCONFIG_NETFILTER_ADVANCED=yCONFIG_BRIDGE_NETFILTER=y
## Core Netfilter Configuration## CONFIG_NETFILTER_NETLINK_QUEUE is not set# CONFIG_NETFILTER_NETLINK_LOG is not set# CONFIG_NF_CONNTRACK is not setCONFIG_NETFILTER_XTABLES=yCONFIG_NETFILTER_XT_TARGET_CLASSIFY=y# CONFIG_NETFILTER_XT_TARGET_DSCP is not setCONFIG_NETFILTER_XT_TARGET_MARK=yCONFIG_NETFILTER_XT_TARGET_NFQUEUE=y# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set# CONFIG_NETFILTER_XT_TARGET_TRACE is not set# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set# CONFIG_NETFILTER_XT_MATCH_COMMENT is not setCONFIG_NETFILTER_XT_MATCH_DCCP=y# CONFIG_NETFILTER_XT_MATCH_DSCP is not set# CONFIG_NETFILTER_XT_MATCH_ESP is not set# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not setCONFIG_NETFILTER_XT_MATCH_LENGTH=yCONFIG_NETFILTER_XT_MATCH_LIMIT=yCONFIG_NETFILTER_XT_MATCH_MAC=yCONFIG_NETFILTER_XT_MATCH_MARK=y# CONFIG_NETFILTER_XT_MATCH_OWNER is not set# CONFIG_NETFILTER_XT_MATCH_POLICY is not set# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not setCONFIG_NETFILTER_XT_MATCH_PHYSDEV=yCONFIG_NETFILTER_XT_MATCH_PKTTYPE=y# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set# CONFIG_NETFILTER_XT_MATCH_RATEEST is not setCONFIG_NETFILTER_XT_MATCH_REALM=yCONFIG_NETFILTER_XT_MATCH_SCTP=y# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not setCONFIG_NETFILTER_XT_MATCH_STRING=yCONFIG_NETFILTER_XT_MATCH_TCPMSS=y# CONFIG_NETFILTER_XT_MATCH_TIME is not set# CONFIG_NETFILTER_XT_MATCH_U32 is not set# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
## IP: Netfilter Configuration## CONFIG_IP_NF_QUEUE is not setCONFIG_IP_NF_IPTABLES=yCONFIG_IP_NF_MATCH_RECENT=yCONFIG_IP_NF_MATCH_ECN=y# CONFIG_IP_NF_MATCH_AH is not setCONFIG_IP_NF_MATCH_TTL=yCONFIG_IP_NF_MATCH_ADDRTYPE=yCONFIG_IP_NF_FILTER=yCONFIG_IP_NF_TARGET_REJECT=yCONFIG_IP_NF_TARGET_LOG=yCONFIG_IP_NF_TARGET_ULOG=yCONFIG_IP_NF_MANGLE=yCONFIG_IP_NF_TARGET_ECN=yCONFIG_IP_NF_TARGET_TTL=yCONFIG_IP_NF_RAW=y# CONFIG_IP_NF_ARPTABLES is not set
## IPv6: Netfilter Configuration#CONFIG_IP6_NF_QUEUE=y# CONFIG_IP6_NF_IPTABLES is not set
## Bridge: Netfilter Configuration## CONFIG_BRIDGE_NF_EBTABLES is not set# CONFIG_IP_DCCP is not set# CONFIG_IP_SCTP is not set# CONFIG_TIPC is not set# CONFIG_ATM is not setCONFIG_BRIDGE=yCONFIG_VLAN_8021Q=y# CONFIG_DECNET is not setCONFIG_LLC=y# CONFIG_LLC2 is not set# CONFIG_IPX is not set# CONFIG_ATALK is not set# CONFIG_X25 is not set# CONFIG_LAPB is not set# CONFIG_ECONET is not set# CONFIG_WAN_ROUTER is not setCONFIG_NET_SCHED=y
## Queueing/Scheduling#CONFIG_NET_SCH_CBQ=yCONFIG_NET_SCH_HTB=y# CONFIG_NET_SCH_HFSC is not setCONFIG_NET_SCH_PRIO=y# CONFIG_NET_SCH_RR is not setCONFIG_NET_SCH_RED=yCONFIG_NET_SCH_SFQ=yCONFIG_NET_SCH_TEQL=yCONFIG_NET_SCH_TBF=yCONFIG_NET_SCH_GRED=yCONFIG_NET_SCH_DSMARK=y# CONFIG_NET_SCH_NETEM is not setCONFIG_NET_SCH_INGRESS=y
## Classification#CONFIG_NET_CLS=yCONFIG_NET_CLS_BASIC=yCONFIG_NET_CLS_TCINDEX=yCONFIG_NET_CLS_ROUTE4=yCONFIG_NET_CLS_ROUTE=yCONFIG_NET_CLS_FW=yCONFIG_NET_CLS_U32=yCONFIG_CLS_U32_PERF=yCONFIG_CLS_U32_MARK=y# CONFIG_NET_CLS_RSVP is not set# CONFIG_NET_CLS_RSVP6 is not set# CONFIG_NET_CLS_FLOW is not set# CONFIG_NET_EMATCH is not setCONFIG_NET_CLS_ACT=yCONFIG_NET_ACT_POLICE=yCONFIG_NET_ACT_GACT=yCONFIG_GACT_PROB=yCONFIG_NET_ACT_MIRRED=yCONFIG_NET_ACT_IPT=y# CONFIG_NET_ACT_NAT is not setCONFIG_NET_ACT_PEDIT=y# CONFIG_NET_ACT_SIMP is not setCONFIG_NET_CLS_IND=yCONFIG_NET_SCH_FIFO=y
## Network testing## CONFIG_NET_PKTGEN is not set# CONFIG_HAMRADIO is not set# CONFIG_CAN is not set# CONFIG_IRDA is not setCONFIG_BT=yCONFIG_BT_L2CAP=yCONFIG_BT_SCO=yCONFIG_BT_RFCOMM=yCONFIG_BT_RFCOMM_TTY=yCONFIG_BT_BNEP=y# CONFIG_BT_BNEP_MC_FILTER is not set# CONFIG_BT_BNEP_PROTO_FILTER is not setCONFIG_BT_HIDP=y
## Bluetooth device drivers#CONFIG_BT_HCIUSB=yCONFIG_BT_HCIUSB_SCO=yCONFIG_BT_HCIUART=yCONFIG_BT_HCIUART_H4=yCONFIG_BT_HCIUART_BCSP=y# CONFIG_BT_HCIUART_LL is not set# CONFIG_BT_HCIBCM203X is not set# CONFIG_BT_HCIBPA10X is not set# CONFIG_BT_HCIBFUSB is not set# CONFIG_BT_HCIVHCI is not set# CONFIG_AF_RXRPC is not setCONFIG_FIB_RULES=y
## Wireless## CONFIG_CFG80211 is not set# CONFIG_WIRELESS_EXT is not set# CONFIG_MAC80211 is not set# CONFIG_IEEE80211 is not set# CONFIG_RFKILL is not set# CONFIG_NET_9P is not set
## Device Drivers#
## Generic Driver Options#CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"# CONFIG_STANDALONE is not set# CONFIG_PREVENT_FIRMWARE_BUILD is not setCONFIG_FW_LOADER=y# CONFIG_DEBUG_DRIVER is not set# CONFIG_DEBUG_DEVRES is not set# CONFIG_SYS_HYPERVISOR is not set# CONFIG_CONNECTOR is not setCONFIG_MTD=y# CONFIG_MTD_DEBUG is not set# CONFIG_MTD_CONCAT is not setCONFIG_MTD_PARTITIONS=y# CONFIG_MTD_REDBOOT_PARTS is not set# CONFIG_MTD_CMDLINE_PARTS is not set# CONFIG_MTD_AR7_PARTS is not set
## User Modules And Translation Layers#CONFIG_MTD_CHAR=yCONFIG_MTD_BLKDEVS=yCONFIG_MTD_BLOCK=y# CONFIG_FTL is not set# CONFIG_NFTL is not set# CONFIG_INFTL is not set# CONFIG_RFD_FTL is not set# CONFIG_SSFDC is not set# CONFIG_MTD_OOPS is not set
## RAM/ROM/Flash chip drivers## CONFIG_MTD_CFI is not set# CONFIG_MTD_JEDECPROBE is not setCONFIG_MTD_MAP_BANK_WIDTH_1=yCONFIG_MTD_MAP_BANK_WIDTH_2=yCONFIG_MTD_MAP_BANK_WIDTH_4=y# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set# CONFIG_MTD_MAP_BANK_WIDTH_32 is not setCONFIG_MTD_CFI_I1=yCONFIG_MTD_CFI_I2=y# CONFIG_MTD_CFI_I4 is not set# CONFIG_MTD_CFI_I8 is not set# CONFIG_MTD_RAM is not set# CONFIG_MTD_ROM is not set# CONFIG_MTD_ABSENT is not set
## Mapping drivers for chip access## CONFIG_MTD_COMPLEX_MAPPINGS is not set# CONFIG_MTD_TS5500 is not set# CONFIG_MTD_INTEL_VR_NOR is not set# CONFIG_MTD_PLATRAM is not set
## Self-contained MTD device drivers## CONFIG_MTD_PMC551 is not set# CONFIG_MTD_SLRAM is not set# CONFIG_MTD_PHRAM is not set# CONFIG_MTD_MTDRAM is not setCONFIG_MTD_BLOCK2MTD=y
## Disk-On-Chip Device Drivers## CONFIG_MTD_DOC2000 is not set# CONFIG_MTD_DOC2001 is not set# CONFIG_MTD_DOC2001PLUS is not set# CONFIG_MTD_NAND is not set# CONFIG_MTD_ONENAND is not set
## UBI - Unsorted block images## CONFIG_MTD_UBI is not set# CONFIG_PARPORT is not setCONFIG_PNP=y# CONFIG_PNP_DEBUG is not set
## Protocols#CONFIG_PNPACPI=yCONFIG_BLK_DEV=y# CONFIG_BLK_DEV_FD is not set# CONFIG_BLK_CPQ_DA is not set# CONFIG_BLK_CPQ_CISS_DA is not set# CONFIG_BLK_DEV_DAC960 is not set# CONFIG_BLK_DEV_UMEM is not set# CONFIG_BLK_DEV_COW_COMMON is not setCONFIG_BLK_DEV_LOOP=yCONFIG_BLK_DEV_CRYPTOLOOP=y# CONFIG_BLK_DEV_NBD is not set# CONFIG_BLK_DEV_SX8 is not set# CONFIG_BLK_DEV_UB is not set# CONFIG_BLK_DEV_RAM is not set# CONFIG_CDROM_PKTCDVD is not set# CONFIG_ATA_OVER_ETH is not setCONFIG_MISC_DEVICES=y# CONFIG_IBM_ASM is not set# CONFIG_PHANTOM is not set# CONFIG_EEPROM_93CX6 is not set# CONFIG_SGI_IOC4 is not set# CONFIG_TIFM_CORE is not set# CONFIG_FUJITSU_LAPTOP is not set# CONFIG_MSI_LAPTOP is not set# CONFIG_SONY_LAPTOP is not set# CONFIG_THINKPAD_ACPI is not set# CONFIG_INTEL_MENLOW is not set# CONFIG_EEEPC_LAPTOP is not set# CONFIG_ENCLOSURE_SERVICES is not setCONFIG_HAVE_IDE=y# CONFIG_IDE is not set
## SCSI device support## CONFIG_RAID_ATTRS is not setCONFIG_SCSI=yCONFIG_SCSI_DMA=y# CONFIG_SCSI_TGT is not set# CONFIG_SCSI_NETLINK is not setCONFIG_SCSI_PROC_FS=y
## SCSI support type (disk, tape, CD-ROM)#CONFIG_BLK_DEV_SD=y# CONFIG_CHR_DEV_ST is not set# CONFIG_CHR_DEV_OSST is not setCONFIG_BLK_DEV_SR=y# CONFIG_BLK_DEV_SR_VENDOR is not setCONFIG_CHR_DEV_SG=y# CONFIG_CHR_DEV_SCH is not set
## Some SCSI devices (e.g. CD jukebox) support multiple LUNs#CONFIG_SCSI_MULTI_LUN=y# CONFIG_SCSI_CONSTANTS is not set# CONFIG_SCSI_LOGGING is not set# CONFIG_SCSI_SCAN_ASYNC is not setCONFIG_SCSI_WAIT_SCAN=m
## SCSI Transports## CONFIG_SCSI_SPI_ATTRS is not set# CONFIG_SCSI_FC_ATTRS is not set# CONFIG_SCSI_ISCSI_ATTRS is not set# CONFIG_SCSI_SAS_ATTRS is not set# CONFIG_SCSI_SAS_LIBSAS is not set# CONFIG_SCSI_SRP_ATTRS is not setCONFIG_SCSI_LOWLEVEL=y# CONFIG_ISCSI_TCP is not set# CONFIG_BLK_DEV_3W_XXXX_RAID is not set# CONFIG_SCSI_3W_9XXX is not set# CONFIG_SCSI_ACARD is not set# CONFIG_SCSI_AACRAID is not set# CONFIG_SCSI_AIC7XXX is not set# CONFIG_SCSI_AIC7XXX_OLD is not set# CONFIG_SCSI_AIC79XX is not set# CONFIG_SCSI_AIC94XX is not set# CONFIG_SCSI_DPT_I2O is not set# CONFIG_SCSI_ADVANSYS is not set# CONFIG_SCSI_ARCMSR is not set# CONFIG_MEGARAID_NEWGEN is not set# CONFIG_MEGARAID_LEGACY is not set# CONFIG_MEGARAID_SAS is not set# CONFIG_SCSI_HPTIOP is not set# CONFIG_SCSI_BUSLOGIC is not set# CONFIG_SCSI_DMX3191D is not set# CONFIG_SCSI_EATA is not set# CONFIG_SCSI_FUTURE_DOMAIN is not set# CONFIG_SCSI_GDTH is not set# CONFIG_SCSI_IPS is not set# CONFIG_SCSI_INITIO is not set# CONFIG_SCSI_INIA100 is not set# CONFIG_SCSI_MVSAS is not set# CONFIG_SCSI_STEX is not set# CONFIG_SCSI_SYM53C8XX_2 is not set# CONFIG_SCSI_IPR is not set# CONFIG_SCSI_QLOGIC_1280 is not set# CONFIG_SCSI_QLA_FC is not set# CONFIG_SCSI_QLA_ISCSI is not set# CONFIG_SCSI_LPFC is not set# CONFIG_SCSI_DC395x is not set# CONFIG_SCSI_DC390T is not set# CONFIG_SCSI_DEBUG is not set# CONFIG_SCSI_SRP is not setCONFIG_ATA=y# CONFIG_ATA_NONSTANDARD is not setCONFIG_ATA_ACPI=yCONFIG_SATA_PMP=yCONFIG_SATA_AHCI=y# CONFIG_SATA_SIL24 is not setCONFIG_ATA_SFF=y# CONFIG_SATA_SVW is not set# CONFIG_ATA_PIIX is not set# CONFIG_SATA_MV is not setCONFIG_SATA_NV=y# CONFIG_PDC_ADMA is not set# CONFIG_SATA_QSTOR is not set# CONFIG_SATA_PROMISE is not set# CONFIG_SATA_SX4 is not set# CONFIG_SATA_SIL is not set# CONFIG_SATA_SIS is not set# CONFIG_SATA_ULI is not set# CONFIG_SATA_VIA is not set# CONFIG_SATA_VITESSE is not set# CONFIG_SATA_INIC162X is not set# CONFIG_PATA_ACPI is not set# CONFIG_PATA_ALI is not setCONFIG_PATA_AMD=m# CONFIG_PATA_ARTOP is not set# CONFIG_PATA_ATIIXP is not set# CONFIG_PATA_CMD640_PCI is not set# CONFIG_PATA_CMD64X is not set# CONFIG_PATA_CS5520 is not set# CONFIG_PATA_CS5530 is not set# CONFIG_PATA_CYPRESS is not set# CONFIG_PATA_EFAR is not set# CONFIG_ATA_GENERIC is not set# CONFIG_PATA_HPT366 is not set# CONFIG_PATA_HPT37X is not set# CONFIG_PATA_HPT3X2N is not set# CONFIG_PATA_HPT3X3 is not set# CONFIG_PATA_IT821X is not set# CONFIG_PATA_IT8213 is not set# CONFIG_PATA_JMICRON is not set# CONFIG_PATA_TRIFLEX is not set# CONFIG_PATA_MARVELL is not set# CONFIG_PATA_MPIIX is not set# CONFIG_PATA_OLDPIIX is not set# CONFIG_PATA_NETCELL is not set# CONFIG_PATA_NINJA32 is not set# CONFIG_PATA_NS87410 is not set# CONFIG_PATA_NS87415 is not set# CONFIG_PATA_OPTI is not set# CONFIG_PATA_OPTIDMA is not set# CONFIG_PATA_PDC_OLD is not set# CONFIG_PATA_RADISYS is not set# CONFIG_PATA_RZ1000 is not set# CONFIG_PATA_SC1200 is not set# CONFIG_PATA_SERVERWORKS is not set# CONFIG_PATA_PDC2027X is not set# CONFIG_PATA_SIL680 is not set# CONFIG_PATA_SIS is not set# CONFIG_PATA_VIA is not set# CONFIG_PATA_WINBOND is not set# CONFIG_PATA_PLATFORM is not set# CONFIG_PATA_SCH is not setCONFIG_MD=yCONFIG_BLK_DEV_MD=y# CONFIG_MD_LINEAR is not set# CONFIG_MD_RAID0 is not setCONFIG_MD_RAID1=y# CONFIG_MD_RAID10 is not set# CONFIG_MD_RAID456 is not set# CONFIG_MD_MULTIPATH is not set# CONFIG_MD_FAULTY is not setCONFIG_BLK_DEV_DM=y# CONFIG_DM_DEBUG is not setCONFIG_DM_CRYPT=yCONFIG_DM_SNAPSHOT=yCONFIG_DM_MIRROR=yCONFIG_DM_ZERO=y# CONFIG_DM_MULTIPATH is not set# CONFIG_DM_DELAY is not set# CONFIG_DM_UEVENT is not set# CONFIG_FUSION is not set
## IEEE 1394 (FireWire) support## CONFIG_FIREWIRE is not set# CONFIG_IEEE1394 is not set# CONFIG_I2O is not set# CONFIG_MACINTOSH_DRIVERS is not setCONFIG_NETDEVICES=y# CONFIG_NETDEVICES_MULTIQUEUE is not set# CONFIG_IFB is not set# CONFIG_DUMMY is not set# CONFIG_BONDING is not set# CONFIG_MACVLAN is not set# CONFIG_EQUALIZER is not setCONFIG_TUN=y# CONFIG_VETH is not set# CONFIG_NET_SB1000 is not set# CONFIG_ARCNET is not set# CONFIG_PHYLIB is not setCONFIG_NET_ETHERNET=yCONFIG_MII=y# CONFIG_HAPPYMEAL is not set# CONFIG_SUNGEM is not set# CONFIG_CASSINI is not set# CONFIG_NET_VENDOR_3COM is not set# CONFIG_NET_TULIP is not set# CONFIG_HP100 is not set# CONFIG_IBM_NEW_EMAC_ZMII is not set# CONFIG_IBM_NEW_EMAC_RGMII is not set# CONFIG_IBM_NEW_EMAC_TAH is not set# CONFIG_IBM_NEW_EMAC_EMAC4 is not setCONFIG_NET_PCI=y# CONFIG_PCNET32 is not set# CONFIG_AMD8111_ETH is not set# CONFIG_ADAPTEC_STARFIRE is not set# CONFIG_B44 is not setCONFIG_FORCEDETH=m# CONFIG_FORCEDETH_NAPI is not set# CONFIG_EEPRO100 is not setCONFIG_E100=y# CONFIG_FEALNX is not set# CONFIG_NATSEMI is not set# CONFIG_NE2K_PCI is not set# CONFIG_8139CP is not set# CONFIG_8139TOO is not set# CONFIG_R6040 is not set# CONFIG_SIS900 is not set# CONFIG_EPIC100 is not set# CONFIG_SUNDANCE is not set# CONFIG_VIA_RHINE is not set# CONFIG_SC92031 is not setCONFIG_NETDEV_1000=y# CONFIG_ACENIC is not set# CONFIG_DL2K is not set# CONFIG_E1000 is not setCONFIG_E1000E=yCONFIG_E1000E_ENABLED=y# CONFIG_IP1000 is not set# CONFIG_IGB is not set# CONFIG_NS83820 is not set# CONFIG_HAMACHI is not set# CONFIG_YELLOWFIN is not setCONFIG_R8169=yCONFIG_R8169_NAPI=yCONFIG_R8169_VLAN=y# CONFIG_SIS190 is not set# CONFIG_SKGE is not set# CONFIG_SKY2 is not set# CONFIG_VIA_VELOCITY is not set# CONFIG_TIGON3 is not set# CONFIG_BNX2 is not set# CONFIG_QLA3XXX is not set# CONFIG_ATL1 is not setCONFIG_NETDEV_10000=y# CONFIG_CHELSIO_T1 is not set# CONFIG_CHELSIO_T3 is not set# CONFIG_IXGBE is not set# CONFIG_IXGB is not set# CONFIG_S2IO is not set# CONFIG_MYRI10GE is not set# CONFIG_NETXEN_NIC is not set# CONFIG_NIU is not set# CONFIG_MLX4_CORE is not set# CONFIG_TEHUTI is not set# CONFIG_BNX2X is not set# CONFIG_SFC is not set# CONFIG_TR is not set
## Wireless LAN## CONFIG_WLAN_PRE80211 is not set# CONFIG_WLAN_80211 is not set# CONFIG_IWLWIFI_LEDS is not set
## USB Network Adapters## CONFIG_USB_CATC is not set# CONFIG_USB_KAWETH is not set# CONFIG_USB_PEGASUS is not set# CONFIG_USB_RTL8150 is not setCONFIG_USB_USBNET=mCONFIG_USB_NET_AX8817X=mCONFIG_USB_NET_CDCETHER=m# CONFIG_USB_NET_DM9601 is not set# CONFIG_USB_NET_GL620A is not setCONFIG_USB_NET_NET1080=m# CONFIG_USB_NET_PLUSB is not set# CONFIG_USB_NET_MCS7830 is not set# CONFIG_USB_NET_RNDIS_HOST is not set# CONFIG_USB_NET_CDC_SUBSET is not setCONFIG_USB_NET_ZAURUS=m# CONFIG_WAN is not set# CONFIG_FDDI is not set# CONFIG_HIPPI is not set# CONFIG_PPP is not set# CONFIG_SLIP is not set# CONFIG_NET_FC is not set# CONFIG_NETCONSOLE is not set# CONFIG_NETPOLL is not set# CONFIG_NET_POLL_CONTROLLER is not set# CONFIG_ISDN is not set# CONFIG_PHONE is not set
## Input device support#CONFIG_INPUT=y# CONFIG_INPUT_FF_MEMLESS is not set# CONFIG_INPUT_POLLDEV is not set
## Userland interfaces#CONFIG_INPUT_MOUSEDEV=y# CONFIG_INPUT_MOUSEDEV_PSAUX is not setCONFIG_INPUT_MOUSEDEV_SCREEN_X=1600CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1200CONFIG_INPUT_JOYDEV=yCONFIG_INPUT_EVDEV=y# CONFIG_INPUT_EVBUG is not set
## Input Device Drivers#CONFIG_INPUT_KEYBOARD=yCONFIG_KEYBOARD_ATKBD=y# CONFIG_KEYBOARD_SUNKBD is not set# CONFIG_KEYBOARD_LKKBD is not set# CONFIG_KEYBOARD_XTKBD is not set# CONFIG_KEYBOARD_NEWTON is not set# CONFIG_KEYBOARD_STOWAWAY is not setCONFIG_INPUT_MOUSE=y# CONFIG_MOUSE_PS2 is not set# CONFIG_MOUSE_SERIAL is not set# CONFIG_MOUSE_APPLETOUCH is not set# CONFIG_MOUSE_VSXXXAA is not setCONFIG_INPUT_JOYSTICK=yCONFIG_JOYSTICK_ANALOG=m# CONFIG_JOYSTICK_A3D is not set# CONFIG_JOYSTICK_ADI is not set# CONFIG_JOYSTICK_COBRA is not set# CONFIG_JOYSTICK_GF2K is not set# CONFIG_JOYSTICK_GRIP is not set# CONFIG_JOYSTICK_GRIP_MP is not set# CONFIG_JOYSTICK_GUILLEMOT is not set# CONFIG_JOYSTICK_INTERACT is not set# CONFIG_JOYSTICK_SIDEWINDER is not set# CONFIG_JOYSTICK_TMDC is not set# CONFIG_JOYSTICK_IFORCE is not set# CONFIG_JOYSTICK_WARRIOR is not set# CONFIG_JOYSTICK_MAGELLAN is not set# CONFIG_JOYSTICK_SPACEORB is not set# CONFIG_JOYSTICK_SPACEBALL is not set# CONFIG_JOYSTICK_STINGER is not set# CONFIG_JOYSTICK_TWIDJOY is not set# CONFIG_JOYSTICK_ZHENHUA is not set# CONFIG_JOYSTICK_JOYDUMP is not set# CONFIG_JOYSTICK_XPAD is not set# CONFIG_INPUT_TABLET is not set# CONFIG_INPUT_TOUCHSCREEN is not setCONFIG_INPUT_MISC=y# CONFIG_INPUT_PCSPKR is not set# CONFIG_INPUT_ATLAS_BTNS is not set# CONFIG_INPUT_ATI_REMOTE is not set# CONFIG_INPUT_ATI_REMOTE2 is not set# CONFIG_INPUT_KEYSPAN_REMOTE is not set# CONFIG_INPUT_POWERMATE is not set# CONFIG_INPUT_YEALINK is not set# CONFIG_INPUT_UINPUT is not set
## Hardware I/O ports#CONFIG_SERIO=yCONFIG_SERIO_I8042=yCONFIG_SERIO_SERPORT=y# CONFIG_SERIO_CT82C710 is not set# CONFIG_SERIO_PCIPS2 is not setCONFIG_SERIO_LIBPS2=y# CONFIG_SERIO_RAW is not setCONFIG_GAMEPORT=m# CONFIG_GAMEPORT_NS558 is not set# CONFIG_GAMEPORT_L4 is not setCONFIG_GAMEPORT_EMU10K1=m# CONFIG_GAMEPORT_FM801 is not set
## Character devices#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_HW_CONSOLE=y# CONFIG_VT_HW_CONSOLE_BINDING is not setCONFIG_DEVKMEM=y# CONFIG_SERIAL_NONSTANDARD is not set# CONFIG_NOZOMI is not set
## Serial drivers#CONFIG_SERIAL_8250=yCONFIG_SERIAL_8250_CONSOLE=yCONFIG_FIX_EARLYCON_MEM=yCONFIG_SERIAL_8250_PCI=yCONFIG_SERIAL_8250_PNP=yCONFIG_SERIAL_8250_NR_UARTS=4CONFIG_SERIAL_8250_RUNTIME_UARTS=4# CONFIG_SERIAL_8250_EXTENDED is not set
## Non-8250 serial port support#CONFIG_SERIAL_CORE=yCONFIG_SERIAL_CORE_CONSOLE=yCONFIG_CONSOLE_POLL=y# CONFIG_SERIAL_JSM is not setCONFIG_UNIX98_PTYS=y# CONFIG_LEGACY_PTYS is not set# CONFIG_IPMI_HANDLER is not set# CONFIG_HW_RANDOM is not set# CONFIG_NVRAM is not setCONFIG_RTC=y# CONFIG_R3964 is not set# CONFIG_APPLICOM is not set# CONFIG_MWAVE is not set# CONFIG_PC8736x_GPIO is not set# CONFIG_RAW_DRIVER is not set# CONFIG_HPET is not set# CONFIG_HANGCHECK_TIMER is not set# CONFIG_TCG_TPM is not set# CONFIG_TELCLOCK is not setCONFIG_DEVPORT=yCONFIG_I2C=yCONFIG_I2C_BOARDINFO=yCONFIG_I2C_CHARDEV=yCONFIG_I2C_ALGOBIT=m
## I2C Hardware Bus support## CONFIG_I2C_ALI1535 is not set# CONFIG_I2C_ALI1563 is not set# CONFIG_I2C_ALI15X3 is not set# CONFIG_I2C_AMD756 is not set# CONFIG_I2C_AMD8111 is not set# CONFIG_I2C_I801 is not set# CONFIG_I2C_I810 is not set# CONFIG_I2C_PIIX4 is not setCONFIG_I2C_NFORCE2=y# CONFIG_I2C_OCORES is not set# CONFIG_I2C_PARPORT_LIGHT is not set# CONFIG_I2C_PROSAVAGE is not set# CONFIG_I2C_SAVAGE4 is not set# CONFIG_I2C_SIMTEC is not set# CONFIG_I2C_SIS5595 is not set# CONFIG_I2C_SIS630 is not set# CONFIG_I2C_SIS96X is not set# CONFIG_I2C_TAOS_EVM is not set# CONFIG_I2C_STUB is not set# CONFIG_I2C_TINY_USB is not set# CONFIG_I2C_VIA is not set# CONFIG_I2C_VIAPRO is not set# CONFIG_I2C_VOODOO3 is not set# CONFIG_I2C_PCA_PLATFORM is not set
## Miscellaneous I2C Chip support## CONFIG_DS1682 is not set# CONFIG_SENSORS_EEPROM is not set# CONFIG_SENSORS_PCF8574 is not set# CONFIG_PCF8575 is not set# CONFIG_SENSORS_PCF8591 is not set# CONFIG_SENSORS_MAX6875 is not set# CONFIG_SENSORS_TSL2550 is not set# CONFIG_I2C_DEBUG_CORE is not set# CONFIG_I2C_DEBUG_ALGO is not set# CONFIG_I2C_DEBUG_BUS is not set# CONFIG_I2C_DEBUG_CHIP is not set# CONFIG_SPI is not set# CONFIG_W1 is not setCONFIG_POWER_SUPPLY=y# CONFIG_POWER_SUPPLY_DEBUG is not set# CONFIG_PDA_POWER is not set# CONFIG_BATTERY_DS2760 is not setCONFIG_HWMON=yCONFIG_HWMON_VID=y# CONFIG_SENSORS_ABITUGURU is not set# CONFIG_SENSORS_ABITUGURU3 is not set# CONFIG_SENSORS_AD7418 is not set# CONFIG_SENSORS_ADM1021 is not set# CONFIG_SENSORS_ADM1025 is not set# CONFIG_SENSORS_ADM1026 is not set# CONFIG_SENSORS_ADM1029 is not set# CONFIG_SENSORS_ADM1031 is not set# CONFIG_SENSORS_ADM9240 is not set# CONFIG_SENSORS_ADT7470 is not set# CONFIG_SENSORS_ADT7473 is not setCONFIG_SENSORS_K8TEMP=m# CONFIG_SENSORS_ASB100 is not set# CONFIG_SENSORS_ATXP1 is not set# CONFIG_SENSORS_DS1621 is not set# CONFIG_SENSORS_I5K_AMB is not set# CONFIG_SENSORS_F71805F is not set# CONFIG_SENSORS_F71882FG is not set# CONFIG_SENSORS_F75375S is not set# CONFIG_SENSORS_FSCHER is not set# CONFIG_SENSORS_FSCPOS is not set# CONFIG_SENSORS_FSCHMD is not set# CONFIG_SENSORS_GL518SM is not set# CONFIG_SENSORS_GL520SM is not set# CONFIG_SENSORS_CORETEMP is not setCONFIG_SENSORS_IT87=y# CONFIG_SENSORS_LM63 is not set# CONFIG_SENSORS_LM75 is not set# CONFIG_SENSORS_LM77 is not set# CONFIG_SENSORS_LM78 is not set# CONFIG_SENSORS_LM80 is not set# CONFIG_SENSORS_LM83 is not set# CONFIG_SENSORS_LM85 is not set# CONFIG_SENSORS_LM87 is not set# CONFIG_SENSORS_LM90 is not set# CONFIG_SENSORS_LM92 is not set# CONFIG_SENSORS_LM93 is not set# CONFIG_SENSORS_MAX1619 is not set# CONFIG_SENSORS_MAX6650 is not set# CONFIG_SENSORS_PC87360 is not set# CONFIG_SENSORS_PC87427 is not set# CONFIG_SENSORS_SIS5595 is not set# CONFIG_SENSORS_DME1737 is not set# CONFIG_SENSORS_SMSC47M1 is not set# CONFIG_SENSORS_SMSC47M192 is not set# CONFIG_SENSORS_SMSC47B397 is not set# CONFIG_SENSORS_ADS7828 is not set# CONFIG_SENSORS_THMC50 is not set# CONFIG_SENSORS_VIA686A is not set# CONFIG_SENSORS_VT1211 is not set# CONFIG_SENSORS_VT8231 is not set# CONFIG_SENSORS_W83781D is not set# CONFIG_SENSORS_W83791D is not set# CONFIG_SENSORS_W83792D is not set# CONFIG_SENSORS_W83793 is not set# CONFIG_SENSORS_W83L785TS is not set# CONFIG_SENSORS_W83L786NG is not set# CONFIG_SENSORS_W83627HF is not set# CONFIG_SENSORS_W83627EHF is not set# CONFIG_SENSORS_HDAPS is not set# CONFIG_SENSORS_APPLESMC is not set# CONFIG_HWMON_DEBUG_CHIP is not setCONFIG_THERMAL=y# CONFIG_WATCHDOG is not set
## Sonics Silicon Backplane#CONFIG_SSB_POSSIBLE=y# CONFIG_SSB is not set
## Multifunction device drivers## CONFIG_MFD_SM501 is not set# CONFIG_HTC_PASIC3 is not set
## Multimedia devices#
## Multimedia core support#CONFIG_VIDEO_DEV=mCONFIG_VIDEO_V4L2_COMMON=mCONFIG_VIDEO_ALLOW_V4L1=yCONFIG_VIDEO_V4L1_COMPAT=y# CONFIG_DVB_CORE is not setCONFIG_VIDEO_MEDIA=m
## Multimedia drivers## CONFIG_MEDIA_ATTACH is not setCONFIG_MEDIA_TUNER=m# CONFIG_MEDIA_TUNER_CUSTOMIZE is not setCONFIG_MEDIA_TUNER_SIMPLE=mCONFIG_MEDIA_TUNER_TDA8290=mCONFIG_MEDIA_TUNER_TDA9887=mCONFIG_MEDIA_TUNER_TEA5761=mCONFIG_MEDIA_TUNER_TEA5767=mCONFIG_MEDIA_TUNER_MT20XX=mCONFIG_MEDIA_TUNER_XC2028=mCONFIG_MEDIA_TUNER_XC5000=mCONFIG_VIDEO_V4L2=mCONFIG_VIDEO_V4L1=m# CONFIG_VIDEO_CAPTURE_DRIVERS is not set# CONFIG_RADIO_ADAPTERS is not set# CONFIG_DAB is not set
## Graphics support#CONFIG_AGP=yCONFIG_AGP_AMD64=y# CONFIG_AGP_INTEL is not set# CONFIG_AGP_SIS is not set# CONFIG_AGP_VIA is not setCONFIG_DRM=m# CONFIG_DRM_TDFX is not set# CONFIG_DRM_R128 is not setCONFIG_DRM_RADEON=m# CONFIG_DRM_MGA is not set# CONFIG_DRM_SIS is not set# CONFIG_DRM_VIA is not set# CONFIG_DRM_SAVAGE is not set# CONFIG_VGASTATE is not set# CONFIG_VIDEO_OUTPUT_CONTROL is not setCONFIG_FB=m# CONFIG_FIRMWARE_EDID is not setCONFIG_FB_DDC=mCONFIG_FB_CFB_FILLRECT=mCONFIG_FB_CFB_COPYAREA=mCONFIG_FB_CFB_IMAGEBLIT=m# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set# CONFIG_FB_SYS_FILLRECT is not set# CONFIG_FB_SYS_COPYAREA is not set# CONFIG_FB_SYS_IMAGEBLIT is not set# CONFIG_FB_FOREIGN_ENDIAN is not set# CONFIG_FB_SYS_FOPS is not set# CONFIG_FB_SVGALIB is not set# CONFIG_FB_MACMODES is not set# CONFIG_FB_BACKLIGHT is not setCONFIG_FB_MODE_HELPERS=y# CONFIG_FB_TILEBLITTING is not set
## Frame buffer hardware drivers## CONFIG_FB_CIRRUS is not set# CONFIG_FB_PM2 is not set# CONFIG_FB_CYBER2000 is not set# CONFIG_FB_ARC is not set# CONFIG_FB_VGA16 is not set# CONFIG_FB_N411 is not set# CONFIG_FB_HGA is not set# CONFIG_FB_S1D13XXX is not set# CONFIG_FB_NVIDIA is not set# CONFIG_FB_RIVA is not set# CONFIG_FB_LE80578 is not set# CONFIG_FB_INTEL is not set# CONFIG_FB_MATROX is not setCONFIG_FB_RADEON=mCONFIG_FB_RADEON_I2C=y# CONFIG_FB_RADEON_BACKLIGHT is not setCONFIG_FB_RADEON_DEBUG=y# CONFIG_FB_ATY128 is not set# CONFIG_FB_ATY is not set# CONFIG_FB_S3 is not set# CONFIG_FB_SAVAGE is not set# CONFIG_FB_SIS is not set# CONFIG_FB_NEOMAGIC is not set# CONFIG_FB_KYRO is not set# CONFIG_FB_3DFX is not set# CONFIG_FB_VOODOO1 is not set# CONFIG_FB_VT8623 is not set# CONFIG_FB_TRIDENT is not set# CONFIG_FB_ARK is not set# CONFIG_FB_PM3 is not set# CONFIG_FB_GEODE is not set# CONFIG_FB_VIRTUAL is not setCONFIG_BACKLIGHT_LCD_SUPPORT=y# CONFIG_LCD_CLASS_DEVICE is not setCONFIG_BACKLIGHT_CLASS_DEVICE=y# CONFIG_BACKLIGHT_CORGI is not set# CONFIG_BACKLIGHT_PROGEAR is not set
## Display device support#CONFIG_DISPLAY_SUPPORT=y
## Display hardware drivers#
## Console display driver support#CONFIG_VGA_CONSOLE=yCONFIG_VGACON_SOFT_SCROLLBACK=yCONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64CONFIG_VIDEO_SELECT=yCONFIG_DUMMY_CONSOLE=yCONFIG_FRAMEBUFFER_CONSOLE=m# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not setCONFIG_FRAMEBUFFER_CONSOLE_ROTATION=yCONFIG_FONTS=y# CONFIG_FONT_8x8 is not set# CONFIG_FONT_8x16 is not set# CONFIG_FONT_6x11 is not set# CONFIG_FONT_7x14 is not set# CONFIG_FONT_PEARL_8x8 is not set# CONFIG_FONT_ACORN_8x8 is not set# CONFIG_FONT_MINI_4x6 is not set# CONFIG_FONT_SUN8x16 is not setCONFIG_FONT_SUN12x22=y# CONFIG_FONT_10x18 is not setCONFIG_LOGO=yCONFIG_LOGO_LINUX_MONO=yCONFIG_LOGO_LINUX_VGA16=yCONFIG_LOGO_LINUX_CLUT224=y
## Sound#CONFIG_SOUND=y
## Advanced Linux Sound Architecture#CONFIG_SND=yCONFIG_SND_TIMER=yCONFIG_SND_PCM=yCONFIG_SND_HWDEP=mCONFIG_SND_RAWMIDI=mCONFIG_SND_SEQUENCER=y# CONFIG_SND_SEQ_DUMMY is not setCONFIG_SND_OSSEMUL=yCONFIG_SND_MIXER_OSS=yCONFIG_SND_PCM_OSS=y# CONFIG_SND_PCM_OSS_PLUGINS is not setCONFIG_SND_SEQUENCER_OSS=y# CONFIG_SND_RTCTIMER is not set# CONFIG_SND_DYNAMIC_MINORS is not set# CONFIG_SND_SUPPORT_OLD_API is not setCONFIG_SND_VERBOSE_PROCFS=yCONFIG_SND_VERBOSE_PRINTK=yCONFIG_SND_DEBUG=yCONFIG_SND_DEBUG_DETECT=y# CONFIG_SND_PCM_XRUN_DEBUG is not setCONFIG_SND_VMASTER=y
## Generic devices## CONFIG_SND_PCSP is not setCONFIG_SND_AC97_CODEC=m# CONFIG_SND_DUMMY is not set# CONFIG_SND_VIRMIDI is not set# CONFIG_SND_MTPAV is not set# CONFIG_SND_SERIAL_U16550 is not set# CONFIG_SND_MPU401 is not set
## PCI devices## CONFIG_SND_AD1889 is not set# CONFIG_SND_ALS300 is not set# CONFIG_SND_ALS4000 is not set# CONFIG_SND_ALI5451 is not set# CONFIG_SND_ATIIXP is not set# CONFIG_SND_ATIIXP_MODEM is not set# CONFIG_SND_AU8810 is not set# CONFIG_SND_AU8820 is not set# CONFIG_SND_AU8830 is not set# CONFIG_SND_AW2 is not set# CONFIG_SND_AZT3328 is not set# CONFIG_SND_BT87X is not set# CONFIG_SND_CA0106 is not set# CONFIG_SND_CMIPCI is not set# CONFIG_SND_OXYGEN is not set# CONFIG_SND_CS4281 is not set# CONFIG_SND_CS46XX is not set# CONFIG_SND_CS5530 is not set# CONFIG_SND_DARLA20 is not set# CONFIG_SND_GINA20 is not set# CONFIG_SND_LAYLA20 is not set# CONFIG_SND_DARLA24 is not set# CONFIG_SND_GINA24 is not set# CONFIG_SND_LAYLA24 is not set# CONFIG_SND_MONA is not set# CONFIG_SND_MIA is not set# CONFIG_SND_ECHO3G is not set# CONFIG_SND_INDIGO is not set# CONFIG_SND_INDIGOIO is not set# CONFIG_SND_INDIGODJ is not setCONFIG_SND_EMU10K1=m# CONFIG_SND_EMU10K1X is not set# CONFIG_SND_ENS1370 is not set# CONFIG_SND_ENS1371 is not set# CONFIG_SND_ES1938 is not set# CONFIG_SND_ES1968 is not set# CONFIG_SND_FM801 is not setCONFIG_SND_HDA_INTEL=m# CONFIG_SND_HDA_HWDEP is not setCONFIG_SND_HDA_CODEC_REALTEK=yCONFIG_SND_HDA_CODEC_ANALOG=yCONFIG_SND_HDA_CODEC_SIGMATEL=yCONFIG_SND_HDA_CODEC_VIA=yCONFIG_SND_HDA_CODEC_ATIHDMI=yCONFIG_SND_HDA_CODEC_CONEXANT=yCONFIG_SND_HDA_CODEC_CMEDIA=yCONFIG_SND_HDA_CODEC_SI3054=yCONFIG_SND_HDA_GENERIC=y# CONFIG_SND_HDA_POWER_SAVE is not set# CONFIG_SND_HDSP is not set# CONFIG_SND_HDSPM is not set# CONFIG_SND_HIFIER is not set# CONFIG_SND_ICE1712 is not set# CONFIG_SND_ICE1724 is not set# CONFIG_SND_INTEL8X0 is not set# CONFIG_SND_INTEL8X0M is not set# CONFIG_SND_KORG1212 is not set# CONFIG_SND_MAESTRO3 is not set# CONFIG_SND_MIXART is not set# CONFIG_SND_NM256 is not set# CONFIG_SND_PCXHR is not set# CONFIG_SND_RIPTIDE is not set# CONFIG_SND_RME32 is not set# CONFIG_SND_RME96 is not set# CONFIG_SND_RME9652 is not set# CONFIG_SND_SONICVIBES is not set# CONFIG_SND_TRIDENT is not set# CONFIG_SND_VIA82XX is not set# CONFIG_SND_VIA82XX_MODEM is not set# CONFIG_SND_VIRTUOSO is not set# CONFIG_SND_VX222 is not set# CONFIG_SND_YMFPCI is not setCONFIG_SND_AC97_POWER_SAVE=yCONFIG_SND_AC97_POWER_SAVE_DEFAULT=0
## USB devices## CONFIG_SND_USB_AUDIO is not set# CONFIG_SND_USB_USX2Y is not set# CONFIG_SND_USB_CAIAQ is not set
## System on Chip audio support## CONFIG_SND_SOC is not set
## ALSA SoC audio for Freescale SOCs#
## SoC Audio for the Texas Instruments OMAP#
## Open Sound System## CONFIG_SOUND_PRIME is not setCONFIG_AC97_BUS=mCONFIG_HID_SUPPORT=yCONFIG_HID=y# CONFIG_HID_DEBUG is not set# CONFIG_HIDRAW is not set
## USB Input Devices#CONFIG_USB_HID=y# CONFIG_USB_HIDINPUT_POWERBOOK is not set# CONFIG_HID_FF is not set# CONFIG_USB_HIDDEV is not setCONFIG_USB_SUPPORT=yCONFIG_USB_ARCH_HAS_HCD=yCONFIG_USB_ARCH_HAS_OHCI=yCONFIG_USB_ARCH_HAS_EHCI=yCONFIG_USB=yCONFIG_USB_DEBUG=y# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
## Miscellaneous USB options#CONFIG_USB_DEVICEFS=y# CONFIG_USB_DEVICE_CLASS is not set# CONFIG_USB_DYNAMIC_MINORS is not setCONFIG_USB_SUSPEND=y# CONFIG_USB_OTG is not set# CONFIG_USB_OTG_WHITELIST is not set# CONFIG_USB_OTG_BLACKLIST_HUB is not set
## USB Host Controller Drivers## CONFIG_USB_C67X00_HCD is not setCONFIG_USB_EHCI_HCD=y# CONFIG_USB_EHCI_ROOT_HUB_TT is not set# CONFIG_USB_EHCI_TT_NEWSCHED is not set# CONFIG_USB_ISP116X_HCD is not set# CONFIG_USB_ISP1760_HCD is not setCONFIG_USB_OHCI_HCD=y# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not setCONFIG_USB_OHCI_LITTLE_ENDIAN=yCONFIG_USB_UHCI_HCD=y# CONFIG_USB_SL811_HCD is not set# CONFIG_USB_R8A66597_HCD is not set
## USB Device Class drivers## CONFIG_USB_ACM is not setCONFIG_USB_PRINTER=y# CONFIG_USB_WDM is not set
## NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'#
## may also be needed; see USB_STORAGE Help for more information#CONFIG_USB_STORAGE=m# CONFIG_USB_STORAGE_DEBUG is not set# CONFIG_USB_STORAGE_DATAFAB is not set# CONFIG_USB_STORAGE_FREECOM is not set# CONFIG_USB_STORAGE_ISD200 is not set# CONFIG_USB_STORAGE_DPCM is not set# CONFIG_USB_STORAGE_USBAT is not set# CONFIG_USB_STORAGE_SDDR09 is not set# CONFIG_USB_STORAGE_SDDR55 is not set# CONFIG_USB_STORAGE_JUMPSHOT is not set# CONFIG_USB_STORAGE_ALAUDA is not set# CONFIG_USB_STORAGE_ONETOUCH is not set# CONFIG_USB_STORAGE_KARMA is not setCONFIG_USB_STORAGE_CYPRESS_ATACB=y# CONFIG_USB_LIBUSUAL is not set
## USB Imaging devices## CONFIG_USB_MDC800 is not set# CONFIG_USB_MICROTEK is not setCONFIG_USB_MON=y
## USB port drivers#CONFIG_USB_SERIAL=m# CONFIG_USB_EZUSB is not setCONFIG_USB_SERIAL_GENERIC=y# CONFIG_USB_SERIAL_AIRCABLE is not set# CONFIG_USB_SERIAL_AIRPRIME is not set# CONFIG_USB_SERIAL_ARK3116 is not set# CONFIG_USB_SERIAL_BELKIN is not set# CONFIG_USB_SERIAL_CH341 is not set# CONFIG_USB_SERIAL_WHITEHEAT is not set# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set# CONFIG_USB_SERIAL_CP2101 is not set# CONFIG_USB_SERIAL_CYPRESS_M8 is not set# CONFIG_USB_SERIAL_EMPEG is not set# CONFIG_USB_SERIAL_FTDI_SIO is not set# CONFIG_USB_SERIAL_FUNSOFT is not set# CONFIG_USB_SERIAL_VISOR is not set# CONFIG_USB_SERIAL_IPAQ is not set# CONFIG_USB_SERIAL_IR is not set# CONFIG_USB_SERIAL_EDGEPORT is not set# CONFIG_USB_SERIAL_EDGEPORT_TI is not set# CONFIG_USB_SERIAL_GARMIN is not set# CONFIG_USB_SERIAL_IPW is not set# CONFIG_USB_SERIAL_IUU is not set# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set# CONFIG_USB_SERIAL_KEYSPAN is not set# CONFIG_USB_SERIAL_KLSI is not set# CONFIG_USB_SERIAL_KOBIL_SCT is not set# CONFIG_USB_SERIAL_MCT_U232 is not set# CONFIG_USB_SERIAL_MOS7720 is not set# CONFIG_USB_SERIAL_MOS7840 is not set# CONFIG_USB_SERIAL_MOTOROLA is not set# CONFIG_USB_SERIAL_NAVMAN is not setCONFIG_USB_SERIAL_PL2303=m# CONFIG_USB_SERIAL_OTI6858 is not set# CONFIG_USB_SERIAL_SPCP8X5 is not set# CONFIG_USB_SERIAL_HP4X is not set# CONFIG_USB_SERIAL_SAFE is not set# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set# CONFIG_USB_SERIAL_TI is not set# CONFIG_USB_SERIAL_CYBERJACK is not set# CONFIG_USB_SERIAL_XIRCOM is not set# CONFIG_USB_SERIAL_OPTION is not set# CONFIG_USB_SERIAL_OMNINET is not set# CONFIG_USB_SERIAL_DEBUG is not set
## USB Miscellaneous drivers## CONFIG_USB_EMI62 is not set# CONFIG_USB_EMI26 is not set# CONFIG_USB_ADUTUX is not set# CONFIG_USB_AUERSWALD is not set# CONFIG_USB_RIO500 is not set# CONFIG_USB_LEGOTOWER is not set# CONFIG_USB_LCD is not set# CONFIG_USB_BERRY_CHARGE is not set# CONFIG_USB_LED is not set# CONFIG_USB_CYPRESS_CY7C63 is not set# CONFIG_USB_CYTHERM is not set# CONFIG_USB_PHIDGET is not set# CONFIG_USB_IDMOUSE is not set# CONFIG_USB_FTDI_ELAN is not set# CONFIG_USB_APPLEDISPLAY is not set# CONFIG_USB_SISUSBVGA is not set# CONFIG_USB_LD is not set# CONFIG_USB_TRANCEVIBRATOR is not set# CONFIG_USB_IOWARRIOR is not set# CONFIG_USB_TEST is not set# CONFIG_USB_GADGET is not set# CONFIG_MMC is not set# CONFIG_MEMSTICK is not set# CONFIG_NEW_LEDS is not set# CONFIG_ACCESSIBILITY is not set# CONFIG_INFINIBAND is not set# CONFIG_EDAC is not set# CONFIG_RTC_CLASS is not setCONFIG_DMADEVICES=y
## DMA Devices## CONFIG_INTEL_IOATDMA is not set# CONFIG_UIO is not set
## Firmware Drivers## CONFIG_EDD is not set# CONFIG_DELL_RBU is not set# CONFIG_DCDBAS is not setCONFIG_DMIID=y# CONFIG_ISCSI_IBFT_FIND is not set
## File systems#CONFIG_EXT2_FS=yCONFIG_EXT2_FS_XATTR=yCONFIG_EXT2_FS_POSIX_ACL=yCONFIG_EXT2_FS_SECURITY=y# CONFIG_EXT2_FS_XIP is not setCONFIG_EXT3_FS=yCONFIG_EXT3_FS_XATTR=yCONFIG_EXT3_FS_POSIX_ACL=yCONFIG_EXT3_FS_SECURITY=y# CONFIG_EXT4DEV_FS is not setCONFIG_JBD=y# CONFIG_JBD_DEBUG is not setCONFIG_FS_MBCACHE=yCONFIG_REISERFS_FS=y# CONFIG_REISERFS_CHECK is not set# CONFIG_REISERFS_PROC_INFO is not set# CONFIG_REISERFS_FS_XATTR is not set# CONFIG_JFS_FS is not setCONFIG_FS_POSIX_ACL=yCONFIG_XFS_FS=y# CONFIG_XFS_QUOTA is not set# CONFIG_XFS_POSIX_ACL is not set# CONFIG_XFS_RT is not set# CONFIG_XFS_DEBUG is not set# CONFIG_GFS2_FS is not set# CONFIG_OCFS2_FS is not setCONFIG_DNOTIFY=yCONFIG_INOTIFY=yCONFIG_INOTIFY_USER=y# CONFIG_QUOTA is not set# CONFIG_AUTOFS_FS is not setCONFIG_AUTOFS4_FS=yCONFIG_FUSE_FS=yCONFIG_GENERIC_ACL=y
## CD-ROM/DVD Filesystems#CONFIG_ISO9660_FS=yCONFIG_JOLIET=y# CONFIG_ZISOFS is not setCONFIG_UDF_FS=yCONFIG_UDF_NLS=y
## DOS/FAT/NT Filesystems#CONFIG_FAT_FS=yCONFIG_MSDOS_FS=yCONFIG_VFAT_FS=yCONFIG_FAT_DEFAULT_CODEPAGE=932CONFIG_FAT_DEFAULT_IOCHARSET="utf8"# CONFIG_NTFS_FS is not set
## Pseudo filesystems#CONFIG_PROC_FS=yCONFIG_PROC_KCORE=yCONFIG_PROC_SYSCTL=yCONFIG_SYSFS=yCONFIG_TMPFS=yCONFIG_TMPFS_POSIX_ACL=y# CONFIG_HUGETLBFS is not set# CONFIG_HUGETLB_PAGE is not setCONFIG_CONFIGFS_FS=y
## Miscellaneous filesystems## CONFIG_ADFS_FS is not set# CONFIG_AFFS_FS is not set# CONFIG_HFS_FS is not set# CONFIG_HFSPLUS_FS is not set# CONFIG_BEFS_FS is not set# CONFIG_BFS_FS is not set# CONFIG_EFS_FS is not setCONFIG_JFFS2_FS=yCONFIG_JFFS2_FS_DEBUG=0CONFIG_JFFS2_FS_WRITEBUFFER=y# CONFIG_JFFS2_FS_WBUF_VERIFY is not set# CONFIG_JFFS2_SUMMARY is not set# CONFIG_JFFS2_FS_XATTR is not set# CONFIG_JFFS2_COMPRESSION_OPTIONS is not setCONFIG_JFFS2_ZLIB=y# CONFIG_JFFS2_LZO is not setCONFIG_JFFS2_RTIME=y# CONFIG_JFFS2_RUBIN is not setCONFIG_CRAMFS=y# CONFIG_VXFS_FS is not set# CONFIG_MINIX_FS is not set# CONFIG_HPFS_FS is not set# CONFIG_QNX4FS_FS is not set# CONFIG_ROMFS_FS is not set# CONFIG_SYSV_FS is not set# CONFIG_UFS_FS is not setCONFIG_NETWORK_FILESYSTEMS=yCONFIG_NFS_FS=yCONFIG_NFS_V3=yCONFIG_NFS_V3_ACL=y# CONFIG_NFS_V4 is not setCONFIG_NFSD=yCONFIG_NFSD_V2_ACL=yCONFIG_NFSD_V3=yCONFIG_NFSD_V3_ACL=y# CONFIG_NFSD_V4 is not setCONFIG_LOCKD=yCONFIG_LOCKD_V4=yCONFIG_EXPORTFS=yCONFIG_NFS_ACL_SUPPORT=yCONFIG_NFS_COMMON=yCONFIG_SUNRPC=yCONFIG_SUNRPC_GSS=yCONFIG_SUNRPC_BIND34=yCONFIG_RPCSEC_GSS_KRB5=y# CONFIG_RPCSEC_GSS_SPKM3 is not setCONFIG_SMB_FS=yCONFIG_SMB_NLS_DEFAULT=yCONFIG_SMB_NLS_REMOTE="cp850"CONFIG_CIFS=y# CONFIG_CIFS_STATS is not set# CONFIG_CIFS_WEAK_PW_HASH is not setCONFIG_CIFS_XATTR=yCONFIG_CIFS_POSIX=y# CONFIG_CIFS_DEBUG2 is not set# CONFIG_CIFS_EXPERIMENTAL is not set# CONFIG_NCP_FS is not set# CONFIG_CODA_FS is not set# CONFIG_AFS_FS is not set
## Partition Types## CONFIG_PARTITION_ADVANCED is not setCONFIG_MSDOS_PARTITION=yCONFIG_NLS=yCONFIG_NLS_DEFAULT="utf8"CONFIG_NLS_CODEPAGE_437=y# CONFIG_NLS_CODEPAGE_737 is not set# CONFIG_NLS_CODEPAGE_775 is not setCONFIG_NLS_CODEPAGE_850=y# CONFIG_NLS_CODEPAGE_852 is not set# CONFIG_NLS_CODEPAGE_855 is not set# CONFIG_NLS_CODEPAGE_857 is not set# CONFIG_NLS_CODEPAGE_860 is not set# CONFIG_NLS_CODEPAGE_861 is not set# CONFIG_NLS_CODEPAGE_862 is not set# CONFIG_NLS_CODEPAGE_863 is not set# CONFIG_NLS_CODEPAGE_864 is not set# CONFIG_NLS_CODEPAGE_865 is not set# CONFIG_NLS_CODEPAGE_866 is not set# CONFIG_NLS_CODEPAGE_869 is not set# CONFIG_NLS_CODEPAGE_936 is not set# CONFIG_NLS_CODEPAGE_950 is not setCONFIG_NLS_CODEPAGE_932=y# CONFIG_NLS_CODEPAGE_949 is not set# CONFIG_NLS_CODEPAGE_874 is not set# CONFIG_NLS_ISO8859_8 is not set# CONFIG_NLS_CODEPAGE_1250 is not set# CONFIG_NLS_CODEPAGE_1251 is not set# CONFIG_NLS_ASCII is not setCONFIG_NLS_ISO8859_1=y# CONFIG_NLS_ISO8859_2 is not set# CONFIG_NLS_ISO8859_3 is not set# CONFIG_NLS_ISO8859_4 is not set# CONFIG_NLS_ISO8859_5 is not set# CONFIG_NLS_ISO8859_6 is not set# CONFIG_NLS_ISO8859_7 is not set# CONFIG_NLS_ISO8859_9 is not set# CONFIG_NLS_ISO8859_13 is not set# CONFIG_NLS_ISO8859_14 is not setCONFIG_NLS_ISO8859_15=y# CONFIG_NLS_KOI8_R is not set# CONFIG_NLS_KOI8_U is not setCONFIG_NLS_UTF8=y# CONFIG_DLM is not set
## Kernel hacking#CONFIG_TRACE_IRQFLAGS_SUPPORT=yCONFIG_PRINTK_TIME=yCONFIG_ENABLE_WARN_DEPRECATED=yCONFIG_ENABLE_MUST_CHECK=yCONFIG_FRAME_WARN=3072CONFIG_MAGIC_SYSRQ=y# CONFIG_UNUSED_SYMBOLS is not setCONFIG_DEBUG_FS=y# CONFIG_HEADERS_CHECK is not setCONFIG_DEBUG_KERNEL=y# CONFIG_DEBUG_SHIRQ is not setCONFIG_DETECT_SOFTLOCKUP=yCONFIG_SCHED_DEBUG=yCONFIG_SCHEDSTATS=yCONFIG_TIMER_STATS=y# CONFIG_DEBUG_OBJECTS is not set# CONFIG_DEBUG_SLAB is not setCONFIG_DEBUG_PREEMPT=y# CONFIG_DEBUG_RT_MUTEXES is not set# CONFIG_RT_MUTEX_TESTER is not setCONFIG_DEBUG_SPINLOCK=yCONFIG_DEBUG_MUTEXES=yCONFIG_DEBUG_LOCK_ALLOC=yCONFIG_PROVE_LOCKING=yCONFIG_LOCKDEP=y# CONFIG_LOCK_STAT is not set# CONFIG_DEBUG_LOCKDEP is not setCONFIG_TRACE_IRQFLAGS=yCONFIG_DEBUG_SPINLOCK_SLEEP=y# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not setCONFIG_STACKTRACE=y# CONFIG_DEBUG_KOBJECT is not setCONFIG_DEBUG_BUGVERBOSE=yCONFIG_DEBUG_INFO=y# CONFIG_DEBUG_VM is not set# CONFIG_DEBUG_WRITECOUNT is not set# CONFIG_DEBUG_LIST is not set# CONFIG_DEBUG_SG is not setCONFIG_FRAME_POINTER=y# CONFIG_BOOT_PRINTK_DELAY is not set# CONFIG_RCU_TORTURE_TEST is not set# CONFIG_BACKTRACE_SELF_TEST is not set# CONFIG_FAULT_INJECTION is not setCONFIG_LATENCYTOP=y# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set# CONFIG_SAMPLES is not setCONFIG_HAVE_ARCH_KGDB=yCONFIG_KGDB=yCONFIG_KGDB_SERIAL_CONSOLE=y# CONFIG_KGDB_TESTS is not set# CONFIG_NONPROMISC_DEVMEM is not setCONFIG_EARLY_PRINTK=y# CONFIG_DEBUG_STACKOVERFLOW is not set# CONFIG_DEBUG_STACK_USAGE is not set# CONFIG_DEBUG_PAGEALLOC is not set# CONFIG_X86_PTDUMP is not setCONFIG_DEBUG_RODATA=y# CONFIG_DIRECT_GBPAGES is not set# CONFIG_DEBUG_RODATA_TEST is not set# CONFIG_DEBUG_NX_TEST is not setCONFIG_X86_MPPARSE=y# CONFIG_IOMMU_DEBUG is not setCONFIG_IO_DELAY_TYPE_0X80=0CONFIG_IO_DELAY_TYPE_0XED=1CONFIG_IO_DELAY_TYPE_UDELAY=2CONFIG_IO_DELAY_TYPE_NONE=3CONFIG_IO_DELAY_0X80=y# CONFIG_IO_DELAY_0XED is not set# CONFIG_IO_DELAY_UDELAY is not set# CONFIG_IO_DELAY_NONE is not setCONFIG_DEFAULT_IO_DELAY_TYPE=0# CONFIG_DEBUG_BOOT_PARAMS is not set# CONFIG_CPA_DEBUG is not set
## Security options## CONFIG_KEYS is not set# CONFIG_SECURITY is not set# CONFIG_SECURITY_FILE_CAPABILITIES is not setCONFIG_CRYPTO=y
## Crypto core or helper#CONFIG_CRYPTO_ALGAPI=yCONFIG_CRYPTO_AEAD=yCONFIG_CRYPTO_BLKCIPHER=yCONFIG_CRYPTO_HASH=yCONFIG_CRYPTO_MANAGER=y# CONFIG_CRYPTO_GF128MUL is not setCONFIG_CRYPTO_NULL=y# CONFIG_CRYPTO_CRYPTD is not setCONFIG_CRYPTO_AUTHENC=y# CONFIG_CRYPTO_TEST is not set
## Authenticated Encryption with Associated Data## CONFIG_CRYPTO_CCM is not set# CONFIG_CRYPTO_GCM is not set# CONFIG_CRYPTO_SEQIV is not set
## Block modes#CONFIG_CRYPTO_CBC=y# CONFIG_CRYPTO_CTR is not set# CONFIG_CRYPTO_CTS is not set# CONFIG_CRYPTO_ECB is not set# CONFIG_CRYPTO_LRW is not set# CONFIG_CRYPTO_PCBC is not set# CONFIG_CRYPTO_XTS is not set
## Hash modes#CONFIG_CRYPTO_HMAC=y# CONFIG_CRYPTO_XCBC is not set
## Digest## CONFIG_CRYPTO_CRC32C is not set# CONFIG_CRYPTO_MD4 is not setCONFIG_CRYPTO_MD5=yCONFIG_CRYPTO_MICHAEL_MIC=yCONFIG_CRYPTO_SHA1=yCONFIG_CRYPTO_SHA256=y# CONFIG_CRYPTO_SHA512 is not set# CONFIG_CRYPTO_TGR192 is not setCONFIG_CRYPTO_WP512=y
## Ciphers#CONFIG_CRYPTO_AES=yCONFIG_CRYPTO_AES_X86_64=y# CONFIG_CRYPTO_ANUBIS is not setCONFIG_CRYPTO_ARC4=yCONFIG_CRYPTO_BLOWFISH=y# CONFIG_CRYPTO_CAMELLIA is not set# CONFIG_CRYPTO_CAST5 is not set# CONFIG_CRYPTO_CAST6 is not setCONFIG_CRYPTO_DES=y# CONFIG_CRYPTO_FCRYPT is not set# CONFIG_CRYPTO_KHAZAD is not set# CONFIG_CRYPTO_SALSA20 is not set# CONFIG_CRYPTO_SALSA20_X86_64 is not set# CONFIG_CRYPTO_SEED is not set# CONFIG_CRYPTO_SERPENT is not set# CONFIG_CRYPTO_TEA is not set# CONFIG_CRYPTO_TWOFISH is not set# CONFIG_CRYPTO_TWOFISH_X86_64 is not set
## Compression#CONFIG_CRYPTO_DEFLATE=y# CONFIG_CRYPTO_LZO is not setCONFIG_CRYPTO_HW=y# CONFIG_CRYPTO_DEV_HIFN_795X is not setCONFIG_HAVE_KVM=yCONFIG_VIRTUALIZATION=yCONFIG_KVM=y# CONFIG_KVM_INTEL is not setCONFIG_KVM_AMD=y# CONFIG_VIRTIO_PCI is not set# CONFIG_VIRTIO_BALLOON is not set
## Library routines#CONFIG_BITREVERSE=yCONFIG_GENERIC_FIND_FIRST_BIT=yCONFIG_GENERIC_FIND_NEXT_BIT=y# CONFIG_CRC_CCITT is not set# CONFIG_CRC16 is not setCONFIG_CRC_ITU_T=yCONFIG_CRC32=y# CONFIG_CRC7 is not set# CONFIG_LIBCRC32C is not setCONFIG_ZLIB_INFLATE=yCONFIG_ZLIB_DEFLATE=yCONFIG_TEXTSEARCH=yCONFIG_TEXTSEARCH_KMP=yCONFIG_TEXTSEARCH_BM=yCONFIG_TEXTSEARCH_FSM=yCONFIG_PLIST=yCONFIG_HAS_IOMEM=yCONFIG_HAS_IOPORT=yCONFIG_HAS_DMA=y
-- Tobias PGP: http://9ac7e0bc.uguu.deこのメールは十割再利用されたビットで作られています。_______________________________________________linux-pm mailing listlinux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx://lists.linux-foundation.org/mailman/listinfo/linux-pm
