Tejun Heo wrote:
Hello,
again...
David Greaves wrote:
Good :)
Now, not so good :)
Oh, crap. :-)
<grin>
So I hibernated last night and resumed this morning.
Before hibernating I froze and sync'ed. After resume I thawed it. (Sorry
Dave)
Here are some photos of the screen during resume. This is not 100%
reproducable - it seems to occur only if the system is shutdown for
30mins or so.
Tejun, I wonder if error handling during resume is problematic? I got
the same errors in 2.6.21. I have never seen these (or any other libata)
errors other than during resume.
http://www.dgreaves.com/pub/2.6.22-rc5-resume-failure.jpg
(hard to read, here's one from 2.6.21
http://www.dgreaves.com/pub/2.6.21-resume-failure.jpg
Your controller is repeatedly reporting PHY readiness changed exception.
Are you reading the system image from the device attached to the first
SATA port?
Yes if you mean 1st as in the one after the zero-th ...
resume=/dev/sdb4
haze:~# swapon -s
Filename Type Size Used Priority
/dev/sdb4 partition 1004020 0 -1
dmesg snippet below...
sda is part of the /scratch xfs array though. SMART doesn't show any problems
and of course all is well other than during a resume.
sda/b are on sata_sil (a cheap plugin pci card)
I _think_ I've only seen the xfs problem when a resume shows these errors.
The error handling itself tries very hard to ensure that there is no
data corruption in case of errors. All commands which experience
exceptions are retried but if the drive itself is doing something
stupid, there's only so much the driver can do.
How reproducible is the problem? Does the problem go away or occur more
often if you change the drive you write the memory image to?
I don't think there should be activity on the sda drive during resume itself.
[I broke my / md mirror and am using some of that for swap/resume for now]
I did change the swap/resume device to sdd2 (different controller, onboard
sata_via) and there was no EH during resume. The system seemed OK, wrote a few
Gb of video and did a kernel compile.
I repeated this test, no EH during resume, no problems.
I even ran xfs_fsr, the defragment utility, to stress the fs.
I retain this configuration and try again tonight but it looks like there _may_
be a link between EH during resume and my problems...
Of course, I don't understand why it *should* EH during resume, it doesn't
during boot or normal operation...
Any more tests you'd like me to try?
David
dmesg snippet...
sata_sil 0000:00:0a.0: version 2.2
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 16 (level, low) -> IRQ 18
scsi0 : sata_sil
PM: Adding info for No Bus:host0
scsi1 : sata_sil
PM: Adding info for No Bus:host1
ata1: SATA max UDMA/100 cmd 0xf881e080 ctl 0xf881e08a bmdma 0xf881e000 irq 0
ata2: SATA max UDMA/100 cmd 0xf881e0c0 ctl 0xf881e0ca bmdma 0xf881e008 irq 0
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7: Maxtor 6B200M0, BANC1980, max UDMA/100
ata1.00: 390721968 sectors, multi 0: LBA48
ata1.00: configured for UDMA/100
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808
ata2.00: ATA-6: ST3160023AS, 3.18, max UDMA/133
ata2.00: 312581808 sectors, multi 0: LBA48
ata2.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808
ata2.00: configured for UDMA/100
PM: Adding info for No Bus:target0:0:0
scsi 0:0:0:0: Direct-Access ATA Maxtor 6B200M0 BANC PQ: 0 ANSI: 5
PM: Adding info for scsi:0:0:0:0
sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
PM: Adding info for No Bus:target1:0:0
scsi 1:0:0:0: Direct-Access ATA ST3160023AS 3.18 PQ: 0 ANSI: 5
PM: Adding info for scsi:1:0:0:0
sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg1 type 0
_______________________________________________
linux-pm mailing list
linux-pm@xxxxxxxxxxxxxxxxxxxxxxxxxx
https://lists.linux-foundation.org/mailman/listinfo/linux-pm
