On Wednesday, 14 February 2007 16:41, Igor Stoppa wrote:
> On Tue, 2007-02-13 at 10:47 +1100, ext Nigel Cunningham wrote:
> > Hi.
> >
> > On Tue, 2007-02-13 at 00:23 +0100, Rafael J. Wysocki wrote:
> > > Hi,
> > >
> > > Here's my attempt to document the requirements with respect to the basic PM
> > > support in drivers and the testing of that. Comments welcome.
> > >
> > > Greetings,
> > > Rafael
> > >
> > > ---
> > > Documentation/SubmittingDrivers | 10 ++
> > > Documentation/power/drivers-testing.txt | 119 ++++++++++++++++++++++++++++++++
> > > 2 files changed, 129 insertions(+)
> > >
> > > Index: linux-2.6.20-git4/Documentation/SubmittingDrivers
> > > ===================================================================
> > > --- linux-2.6.20-git4.orig/Documentation/SubmittingDrivers
> > > +++ linux-2.6.20-git4/Documentation/SubmittingDrivers
> > > @@ -87,6 +87,16 @@ Clarity: It helps if anyone can see how
> > > driver that intentionally obfuscates how the hardware works
> > > it will go in the bitbucket.
> > >
> > > +PM support: Since Linux is used on many portable and desktop systems, your
> > > + driver is likely to be used on such a system and therefore it
> > > + should support basic power management by implementing, if
> > > + necessary, the .suspend and .resume methods used during the
> > > + system-wide suspend and resume transitions. You should verify
> > > + that your driver correctly handles the suspend and resume, but
> > > + if you are unable to ensure that, please at least define the
> > > + .suspend method returning the -ENOSYS ("Function not
> > > + implemented") error.
> > > +
> > > Control: In general if there is active maintainance of a driver by
> > > the author then patches will be redirected to them unless
> > > they are totally obvious and without need of checking.
> > > Index: linux-2.6.20-git4/Documentation/power/drivers-testing.txt
> > > ===================================================================
> > > --- /dev/null
> > > +++ linux-2.6.20-git4/Documentation/power/drivers-testing.txt
> > > @@ -0,0 +1,119 @@
> > > +Testing suspend and resume support in drivers
> > > + (C) 2007 Rafael J. Wysocki <rjw at sisk.pl>
> > > +
> > > +Unfortunately, to effectively test the support for the system-wide suspend and
> > > +resume transitions in a driver, it is necessary to suspend and resume a fully
> > > +functional system with this driver loaded. Moreover, that should be done many
> > > +times, preferably many times in a row, and separately for the suspend to disk
> > > +(STD) and the suspend to RAM (STR) transitions, because each of these cases
> > > +involves different ordering of operations and different interactions with the
> > > +machine's BIOS.
> > > +
> > > +Of course, for this purpose the test system has to be known to suspend and
> > > +resume without the driver being tested. Thus, if possible, you should first
> > > +resolve all suspend/resume-related problems in the test system before you start
> > > +testing the new driver.
> > > +
> > > +I. Preparing the test system
> > > +
> > > +1. To verify that the STD works, you can try to suspend in the "reboot" mode:
> > > +
> > > +# echo reboot > /sys/power/disk
> > > +# echo disk > /sys/power/state
> > > +
> > > +and the system should suspend, reboot, resume and get back to the command prompt
> > > +where you have started the transition. If that happens, the STD is most likely
> > > +to work correctly, but you can repeat the test a couple of times in a row for
> > > +confidence. You should also test the "platform" and "shutdown" modes of
> >
> > I would say "you need to repeat the test at least a couple of times...",
> > perhaps adding something along the lines of "This is necessary because
> > some problems only show up on a second attempt at suspending and
> > resuming a driver. You can think of it as the driver coming back 'dazed
> > and confused' after the first cycle, and only being properly killed by
> > the second attempt."
>
> "at least a couple of times" sounds very optimistic :-D
Usually two times are enough to trigger the problem in such cases.
> >
> > > +suspend:
> > > +
> > > +# echo platform > /sys/power/disk
> > > +# echo disk > /sys/power/state
> > > +
> > > +or
> > > +
> > > +# echo shutdown > /sys/power/disk
> > > +# echo disk > /sys/power/state
> > > +
> > > +in which cases you will have to press the power button to make the system
> > > +resume. If that works, you are ready to test the STD with the new driver
> > > +loaded. Otherwise, you have to identify what is wrong.
> > > +
> > > +a) To verify if there are any drivers that cause problems you can run the STD
> > > +in the test mode:
> > > +
> > > +# echo test > /sys/power/disk
> > > +# echo disk > /sys/power/state
> > > +
> > > +in which case the system should freeze tasks, suspend devices, disable nonboot
> > > +CPUs (if any), wait for 5 seconds, enable nonboot CPUs, resume devices, thaw
> > > +tasks and return to your command prompt. If that fails, most likely there is
> > > +a driver that fails to either suspend or resume (in the latter case the system
> > > +may hang or be unstable after the test, so please take that into consideration).
> > > +To find this driver, you can carry out a binary search according to the rules:
> > > +- if the test fails, unload a half of the drivers currently loaded and repeat
> > > +(that would probably involve rebooting the system, so always note what drivers
> > > +have been loaded before the test),
> > > +- if the test succeeds, load a half of the drivers you have unloaded most
> > > +recently and repeat.
> > > +
> > > +Once you have found the failing driver (there can be more than just one of
> > > +them), you have to unload it every time before the STD transition. In that case
> > > +please make sure to report the problem with the driver.
> >
> > It is also possible that a cycle can still fail after you have unloaded
> > all modules. In that case, you would want to look in your kernel
> > configuration for possibilities that can be modularised (testing again
> > with them as modules), and possibly also try boot time options such as
> > noapic or noacpi.
>
> The first step, imho, would be to identify all the peripherals requiired
> for a barebone configuration to run (i.e. serial console) and verify
> that at least those can reliably go through several suspend/resume
> cycles. Then the dicotomic approach can be used.
I think in most configurations init=/bin/bash loads the minimal set of drivers
needed. If anyone has certain special need, he will certainly figure out
what to do. :-)
> >
> > > +
> > > +b) If the test mode of STD works, you can boot the system with "init=/bin/bash"
> > > +and attempt to suspend in the "reboot", "shutdown" and "platform" modes. If
> > > +that does not work, there probably is a problem with one of the low level
> > > +drivers and you generally cannot do much about it except for reporting it
> > > +(fortunately, that does not happen very often these days). Otherwise, there is
> >
> > Oh. Perhaps some of the suggestions from above belong here?
> >
> > > +a problem with a modular driver and you can find it by loading a half of the
> > > +modules you normally use and binary searching in accordance with the algorithm:
> > > +- if there are n modules loaded and the attempt to suspend and resume fails,
> > > +unload n/2 of the modules and try again (that would probably involve rebooting
> > > +the system),
> > > +- if there are n modules loaded and the attempt to suspend and resume succeeds,
> > > +load n/2 modules more and try again.
> > > +
> > > +Again, if you find the offending module(s), it(they) must be unloaded every time
> > > +before the STD transition, and please report the problem with it(them).
> > > +
> > > +2. To verify that the STR works, it is generally more convenient to use the
> > > +s2ram tool available from http://suspend.sf.net and documented at
> > > +http://en.opensuse.org/s2ram . However, before doing that it is recommended to
> > > +carry out the procedure described in section 1.
> > > +
> > > +Assume you have resolved the problems with the STD and you have found some
> > > +failing drivers. These drivers are also likely to fail during the STR or
> > > +during the resume, so it is better to unload them every time before the STR
> > > +transition. Now, you can follow the instructions at
> > > +http://en.opensuse.org/s2ram to test the system, but if it does not work
> > > +"out of the box", you may need to boot it with "init=/bin/bash" and test
> > > +s2ram in the minimal configuration. In that case, you may be able to search
> > > +for failing drivers by following the procedure analogous to the one described in
> > > +1b). If you find some failing drivers, you will have to unload them every time
> > > +before the STR transition (ie. before you run s2ram), and please report the
> > > +problem with them.
> > > +
> > > +II. Testing the driver
> > > +
> > > +Once you have resolved the suspend/resume-related problems with your test system
> > > +without the new driver, you are ready to test it:
> Why not first get the driver working against the barebone configuration?
You can start from the barebone and go towards more complete configurations or
start with a more-or-less complete system and simplify the configuration if
there are problems. Anyway, however, you need to test against the complete
system eventually, I think.
Greetings,
Rafael
