On Fri, Feb 28, 2020 at 11:16:59AM +0100, Fawad Lateef wrote:
> Hi Bjorn,
>
> Thanks for your reply. Please see my comments below.
>
> By the way, I have another development kit from "Embedded Artists"
> with i.MX6Q SOM. I did similar test quickly (with WLAN attached to
> PCIe root-complex _not_ PLX switch). This one also showed same
> behavior though I have to confirm this properly (working on it). Then
> at-least I can say its not exactly issue of Phytec SOM.
>
> On Thu, 27 Feb 2020 at 00:27, Bjorn Helgaas <helgaas@xxxxxxxxxx> wrote:
> > On Wed, Feb 26, 2020 at 05:25:52PM -0600, Bjorn Helgaas wrote:
> > > On Sat, Feb 22, 2020 at 04:25:41PM +0100, Fawad Lateef wrote:
> > > > Hello,
> > > >
> > > > I am trying to figure-out an issue on our i.MX6Q platform based design
> > > > where PCIe interface goes bad.
> > > >
> > > > We have a Phytec i.MX6Q eMMC SOM, attached to our custom designed
> > > > board. PCIe root-complex from i.MX6Q is attached to PLX switch
> > > > (PEX8605).
> > > >
> > > > Linux kernel version is 4.19.9x and also 4.14.134 (from phytec's
> > > > linux-mainline repo). Kernel do not have PCIe hot-plug and PNP enabled
> > > > in config.
> > > >
> > > > PLX switch #PERST is attached to a GPIO pin and stays in disable state
> > > > until Linux is booted. So at boot time only PCIe root-complex is
> > > > initialized by kernel.
> > > >
> > > > After boot if I do "lspci -v" and see everything good from PCIe
> > > > root-complex (below):
> > > >
> > > > ~ # lspci -v
> > > > 00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00
> > > > [Normal decode])
> > > > Flags: bus master, fast devsel, latency 0, IRQ 295
> > > > Memory at 01000000 (32-bit, non-prefetchable) [size=1M]
> > > > Bus: primary=00, secondary=01, subordinate=ff, sec-latency=0
> > > > I/O behind bridge: None
> > > > Memory behind bridge: None
> > > > Prefetchable memory behind bridge: None
> > > > [virtual] Expansion ROM at 01100000 [disabled] [size=64K]
> > > > Capabilities: [40] Power Management version 3
> > > > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
> > > > Capabilities: [70] Express Root Port (Slot-), MSI 00
> > > > Capabilities: [100] Advanced Error Reporting
> > > > Capabilities: [140] Virtual Channel
> > > > Kernel driver in use: pcieport
> > > >
> > > >
> > > > Then I enable the #PERST pin of PLX switch, everything is still good
> > > > (no rescan on Linux is done yet)
> > > >
> > > > ~ # echo 139 > /sys/class/gpio/export
> > > > ~ # echo out > /sys/class/gpio/gpio139/direction
> > > > ~ # echo 1 > /sys/class/gpio/gpio139/value
> > > > ~ # lspci -v
> > > > 00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00
> > > > [Normal decode])
> > > > Flags: bus master, fast devsel, latency 0, IRQ 295
> > > > Memory at 01000000 (32-bit, non-prefetchable) [size=1M]
> > > > Bus: primary=00, secondary=01, subordinate=ff, sec-latency=0
> > > > I/O behind bridge: None
> > > > Memory behind bridge: None
> > > > Prefetchable memory behind bridge: None
> > > > [virtual] Expansion ROM at 01100000 [disabled] [size=64K]
> > > > Capabilities: [40] Power Management version 3
> > > > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
> > > > Capabilities: [70] Express Root Port (Slot-), MSI 00
> > > > Capabilities: [100] Advanced Error Reporting
> > > > Capabilities: [140] Virtual Channel
> > > > Kernel driver in use: pcieport
> > > >
> > > >
> > > > Now just disable/put-in-reset the PLX switch (Linux don't see the
> > > > switch yet, as no rescan on PCIe was done). Now "lspci -v" and
> > > > root-complex goes bad.
> > > >
> > > > ~ # echo 0 > /sys/class/gpio/gpio139/value
> > > > ~ # lspci -v
> > > > 00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00
> > > > [Normal decode])
> > > > Flags: fast devsel, IRQ 295
> > > > Memory at 01000000 (64-bit, prefetchable) [disabled] [size=1M]
> > > > Bus: primary=00, secondary=00, subordinate=00, sec-latency=0
> > > > I/O behind bridge: 00000000-00000fff [size=4K]
> > > > Memory behind bridge: 00000000-000fffff [size=1M]
> > > > Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
> > > > [virtual] Expansion ROM at 01100000 [disabled] [size=64K]
> > > > Capabilities: [40] Power Management version 3
> > > > Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
> > > > Capabilities: [70] Express Root Port (Slot-), MSI 00
> > > > Capabilities: [100] Advanced Error Reporting
> > > > Capabilities: [140] Virtual Channel
> > > > Kernel driver in use: pcieport
> > > >
> > > > ~ # uname -a
> > > > Linux buildroot-2019.08-imx6 4.14.134-phy2 #1 SMP Thu Feb 20 12:13:33
> > > > UTC 2020 armv7l GNU/Linux
> > > > ~ #
> > > >
> > > >
> > > > I am really not sure what is going wrong here. Did I am missing
> > > > something basic?
> > >
> > > I agree, it looks like something's wrong, but I really don't have any
> > > ideas.
> > >
> > > I would start by using "lspci -xxxx" to see the actual values we get
> > > from config space. It looks like we're reading zeros from at least
> > > the bus and window registers.
>
> Somehow "lspci -xxxx" generate kernel crash ("imprecise external
> abort") on both Phytec and Embedded Artists SOMs. lspci with -xxx (3
> x) works but not 4 x. Seems like i.MX6 general issue?
Sounds like i.MX6 doesn't handle PCIe errors correctly. "lspci -xxx"
reads the 256-byte PCI config space, while "lspci -xxxx" reads the
entire 4K extended config space. If we read config space that a
device doesn't implement, I think we'll get an Unsupported Request
completion on PCIe. That *should* be handled nicely (without causing
a kernel crash) and turned into a ~0 response to the read. If that
doesn't work, it needs to be solved somewhere in the i.MX6 or ARM arch
code.
Bjorn
