HI Bjorn,
Thanks for the review.
On 2/25/20 5:02 PM, Bjorn Helgaas wrote:
On Thu, Feb 13, 2020 at 10:20:16AM -0800, sathyanarayanan.kuppuswamy@xxxxxxxxxxxxxxx wrote:
From: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@xxxxxxxxxxxxxxx>
As per ACPI specification r6.3, sec 5.6.6, when firmware owns Downstream
Port Containment (DPC), its expected to use the "Error Disconnect
Recover" (EDR) notification to alert OSPM of a DPC event and if OS
supports EDR, its expected to handle the software state invalidation and
port recovery in OS, and also let firmware know the recovery status via
_OST ACPI call. Related _OST status codes can be found in ACPI
specification r6.3, sec 6.3.5.2.
Also, as per PCI firmware specification r3.2 Downstream Port Containment
Related Enhancements ECN, sec 4.5.1, table 4-6, If DPC is controlled by
firmware (firmware first mode), firmware is responsible for
configuring the DPC and OS is responsible for error recovery. Also, OS
is allowed to modify DPC registers only during the EDR notification
window.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@xxxxxxxxxxxxxxx>
---
drivers/pci/pci-acpi.c | 3 +
drivers/pci/pcie/Kconfig | 10 ++
drivers/pci/pcie/Makefile | 1 +
drivers/pci/pcie/edr.c | 257 ++++++++++++++++++++++++++++++++++++++
include/linux/pci-acpi.h | 8 ++
5 files changed, 279 insertions(+)
create mode 100644 drivers/pci/pcie/edr.c
diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
index 0c02d500158f..6af5d6a04990 100644
--- a/drivers/pci/pci-acpi.c
+++ b/drivers/pci/pci-acpi.c
@@ -1258,6 +1258,7 @@ static void pci_acpi_setup(struct device *dev)
acpi_pci_wakeup(pci_dev, false);
acpi_device_power_add_dependent(adev, dev);
+ pci_acpi_add_edr_notifier(pci_dev);
}
static void pci_acpi_cleanup(struct device *dev)
@@ -1276,6 +1277,8 @@ static void pci_acpi_cleanup(struct device *dev)
device_set_wakeup_capable(dev, false);
}
+
+ pci_acpi_remove_edr_notifier(pci_dev);
}
static bool pci_acpi_bus_match(struct device *dev)
diff --git a/drivers/pci/pcie/Kconfig b/drivers/pci/pcie/Kconfig
index 6e3c04b46fb1..772b1f4cb19e 100644
--- a/drivers/pci/pcie/Kconfig
+++ b/drivers/pci/pcie/Kconfig
@@ -140,3 +140,13 @@ config PCIE_BW
This enables PCI Express Bandwidth Change Notification. If
you know link width or rate changes occur only to correct
unreliable links, you may answer Y.
+
+config PCIE_EDR
+ bool "PCI Express Error Disconnect Recover support"
+ depends on PCIE_DPC && ACPI
+ help
+ This option adds Error Disconnect Recover support as specified
+ in the Downstream Port Containment Related Enhancements ECN to
+ the PCI Firmware Specification r3.2. Enable this if you want to
+ support hybrid DPC model which uses both firmware and OS to
+ implement DPC.
diff --git a/drivers/pci/pcie/Makefile b/drivers/pci/pcie/Makefile
index efb9d2e71e9e..68da9280ff11 100644
--- a/drivers/pci/pcie/Makefile
+++ b/drivers/pci/pcie/Makefile
@@ -13,3 +13,4 @@ obj-$(CONFIG_PCIE_PME) += pme.o
obj-$(CONFIG_PCIE_DPC) += dpc.o
obj-$(CONFIG_PCIE_PTM) += ptm.o
obj-$(CONFIG_PCIE_BW) += bw_notification.o
+obj-$(CONFIG_PCIE_EDR) += edr.o
diff --git a/drivers/pci/pcie/edr.c b/drivers/pci/pcie/edr.c
new file mode 100644
index 000000000000..b3e9103585a1
--- /dev/null
+++ b/drivers/pci/pcie/edr.c
@@ -0,0 +1,257 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCI DPC Error Disconnect Recover support driver
+ * Author: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@xxxxxxxxxxxxxxx>
+ *
+ * Copyright (C) 2020 Intel Corp.
+ */
+
+#define dev_fmt(fmt) "EDR: " fmt
+
+#include <linux/pci.h>
+#include <linux/pci-acpi.h>
+
+#include "portdrv.h"
+#include "dpc.h"
+#include "../pci.h"
+
+#define EDR_PORT_ENABLE_DSM 0x0C
+#define EDR_PORT_LOCATE_DSM 0x0D
+#define EDR_OST_SUCCESS 0x80
+#define EDR_OST_FAILED 0x81
+
+/*
+ * _DSM wrapper function to enable/disable DPC port.
+ * @pdev : PCI device structure.
+ * @enable: status of DPC port (0 or 1).
Either line up these colons or join them with the parameter names
(also below).
ok. will do it.
+ * returns 0 on success or errno on failure.
+ */
+static int acpi_enable_dpc_port(struct pci_dev *pdev, bool enable)
We only call this with "true", so the "enable" parameter is pointless.
Makes sense. I will remove it. We can add it if needed in future.
+{
+ struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+ union acpi_object *obj, argv4, req;
+ int status = 0;
+
+ req.type = ACPI_TYPE_INTEGER;
+ req.integer.value = enable;
+
+ argv4.type = ACPI_TYPE_PACKAGE;
+ argv4.package.count = 1;
+ argv4.package.elements = &req;
+
+ /*
+ * Per the Downstream Port Containment Related Enhancements ECN to
+ * the PCI Firmware Specification r3.2, sec 4.6.12,
+ * EDR_PORT_ENABLE_DSM is optional. Return success if it's not
+ * implemented.
+ */
+ obj = acpi_evaluate_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
+ EDR_PORT_ENABLE_DSM, &argv4);
+ if (!obj)
+ return 0;
+
+ if (obj->type != ACPI_TYPE_INTEGER || obj->integer.value != enable)
+ status = -EIO;
+
+ ACPI_FREE(obj);
+
+ return status;
+}
+
+/*
+ * _DSM wrapper function to locate DPC port.
+ * @pdev : Device which received EDR event.
+ *
+ * returns pci_dev or NULL.
+ */
+static struct pci_dev *acpi_locate_dpc_port(struct pci_dev *pdev)
+{
+ struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+ union acpi_object *obj;
+ u16 port;
+
+ obj = acpi_evaluate_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
+ EDR_PORT_LOCATE_DSM, NULL);
+ if (!obj)
+ return pci_dev_get(pdev);
+
+ if (obj->type != ACPI_TYPE_INTEGER) {
If this happens, it's a firmware defect, isn't it? I think maybe we
should warn here. I know we warn below ("No valid port found"), but
that doesn't give any clue about the fact that firmware screwed up.
I will add it in next version.
+ ACPI_FREE(obj);
+ return NULL;
+ }
+
+ /*
+ * Firmware returns DPC port BDF details in following format:
+ * 15:8 = bus
+ * 7:3 = device
+ * 2:0 = function
+ */
+ port = obj->integer.value;
+
+ ACPI_FREE(obj);
+
+ return pci_get_domain_bus_and_slot(pci_domain_nr(pdev->bus),
+ PCI_BUS_NUM(port), port & 0xff);
+}
+
+/*
+ * _OST wrapper function to let firmware know the status of EDR event.
+ * @pdev : Device used to send _OST.
+ * @edev : Device which experienced EDR event.
+ * @status: Status of EDR event.
+ */
+static int acpi_send_edr_status(struct pci_dev *pdev, struct pci_dev *edev,
+ u16 status)
+{
+ struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+ u32 ost_status;
+
+ pci_dbg(pdev, "Sending EDR status :%#x\n", status);
+
+ ost_status = PCI_DEVID(edev->bus->number, edev->devfn);
+ ost_status = (ost_status << 16) | status;
+
+ status = acpi_evaluate_ost(adev->handle,
+ ACPI_NOTIFY_DISCONNECT_RECOVER,
+ ost_status, NULL);
+ if (ACPI_FAILURE(status))
+ return -EINVAL;
+
+ return 0;
+}
+
+pci_ers_result_t edr_dpc_reset_link(void *cb_data)
+{
+ return dpc_reset_link_common(cb_data);
+}
+
+static void edr_handle_event(acpi_handle handle, u32 event, void *data)
+{
+ struct dpc_dev *dpc = data, ndpc;
There's actually very little use of struct dpc_dev in this file. I
bet with a little elbow grease, we could remove it completely and just
use the pci_dev * or maybe an opaque pointer.
Yes, we could remove it. But it might need some more changes to
dpc driver functions. I can think of two ways,
1. Re-factor the DPC driver not to use dpc_dev structure and just use
pci_dev in their functions implementation. But this might lead to
re-reading following dpc_dev structure members every time we
use it in dpc driver functions.
(Currently in dpc driver probe they cache the following device parameters )
9 u16 cap_pos;
10 bool rp_extensions;
11 u8 rp_log_size;
12 u16 ctl;
13 u16 cap;
2. We can create a new variant of dpc_process_err() which depends on
pci_dev
structure and move the dpc_dev initialization to it. Downside is, we
should do this
initialization every time we get DPC event (which should be rare).
void dpc_process_error(struct pci_dev *pdev)
{
struct dpc_dev dpc;
dpc_dev_init(pdev, &dpc);
....
}
Let me know your comments.
+ struct pci_dev *pdev = dpc->pdev;
+ pci_ers_result_t estate = PCI_ERS_RESULT_DISCONNECT;
+ u16 status;
+
+ pci_info(pdev, "ACPI event %#x received\n", event);
+
+ if (event != ACPI_NOTIFY_DISCONNECT_RECOVER)
+ return;
+
+ /*
+ * Check if _DSM(0xD) is available, and if present locate the
+ * port which issued EDR event.
+ */
+ pdev = acpi_locate_dpc_port(pdev);
This function name should include "get" since it's part of the
pci_dev_get()/pci_dev_put() sequence.
How about acpi_dpc_port_get(pdev) ?
+ if (!pdev) {
+ pci_err(dpc->pdev, "No valid port found\n");
+ return;
+ }
+
+ if (pdev != dpc->pdev) {
+ pci_warn(pdev, "Initializing dpc again\n");
+ dpc_dev_init(pdev, &ndpc);
This seems... I'm not sure what. I guess it's really just reading
the DPC capability for use by dpc_process_error(), so maybe it's OK.
But it's a little strange to read.
Is this something we should be warning about?
No this is a valid case. it will only happen if we have a non-acpi based
switch
attached to root port.
I think the ECR says
it's legitimate to return a child device, doesn't it?
+ dpc= &ndpc;
Space before "=".
will fix it in next version.
+ }
+
+ /*
+ * If port does not support DPC, just send the OST:
+ */
+ if (!dpc->cap_pos)
+ goto send_ost;
+
+ /* Check if there is a valid DPC trigger */
+ pci_read_config_word(pdev, dpc->cap_pos + PCI_EXP_DPC_STATUS, &status);
+ if (!(status & PCI_EXP_DPC_STATUS_TRIGGER)) {
+ pci_err(pdev, "Invalid DPC trigger %#010x\n", status);
+ goto send_ost;
+ }
+
+ dpc_process_error(dpc);
+
+ /* Clear AER registers */
+ pci_aer_clear_err_uncor_status(pdev);
+ pci_aer_clear_err_fatal_status(pdev);
+ pci_aer_clear_err_status_regs(pdev);
+
+ /*
+ * Irrespective of whether the DPC event is triggered by
+ * ERR_FATAL or ERR_NONFATAL, since the link is already down,
+ * use the FATAL error recovery path for both cases.
+ */
+ estate = pcie_do_recovery_common(pdev, pci_channel_io_frozen, -1,
+ edr_dpc_reset_link, dpc);
+send_ost:
+
+ /* Use ACPI handle of DPC event device for sending EDR status */
+ dpc = data;
I think it'd be clearer to reserve "dpc" for the device that received
the notification and to which we send the status, and use a different
"e_dpc" or something for the dpc_process_error() and related code.
ok. will make this change in next version.
+ /*
+ * If recovery is successful, send _OST(0xF, BDF << 16 | 0x80)
+ * to firmware. If not successful, send _OST(0xF, BDF << 16 | 0x81).
+ */
+ if (estate == PCI_ERS_RESULT_RECOVERED)
+ acpi_send_edr_status(dpc->pdev, pdev, EDR_OST_SUCCESS);
+ else
+ acpi_send_edr_status(dpc->pdev, pdev, EDR_OST_FAILED);
+
+ pci_dev_put(pdev);
+}
+
+int pci_acpi_add_edr_notifier(struct pci_dev *pdev)
+{
+ struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+ struct dpc_dev *dpc;
+ acpi_status astatus;
+ int status;
+
+ /*
+ * Per the Downstream Port Containment Related Enhancements ECN to
+ * the PCI Firmware Spec, r3.2, sec 4.5.1, table 4-6, EDR support
+ * can only be enabled if DPC is controlled by firmware.
+ *
+ * TODO: Remove dependency on ACPI FIRMWARE_FIRST bit to
+ * determine ownership of DPC between firmware or OS.
Extend the comment to say how we *should* determine ownership.
Yes, ownership should be based on _OSC negotiation. I will add necessary
comments here.
+ */
+ if (!pcie_aer_get_firmware_first(pdev) || pcie_ports_dpc_native)
+ return -ENODEV;
+
+ if (!adev)
+ return 0;
+
+ dpc = devm_kzalloc(&pdev->dev, sizeof(*dpc), GFP_KERNEL);
This kzalloc should be in dpc.c, not here.
And I don't see a corresponding free.
It will be freed when removing the pdev right ? Do you want to free it
explicitly in this driver ?
+ if (!dpc)
+ return -ENOMEM;
+
+ dpc_dev_init(pdev, dpc);
+
+ astatus = acpi_install_notify_handler(adev->handle,
+ ACPI_SYSTEM_NOTIFY,
+ edr_handle_event, dpc);
+ if (ACPI_FAILURE(astatus)) {
+ pci_err(pdev, "Install ACPI_SYSTEM_NOTIFY handler failed\n");
+ return -EBUSY;
+ }
+
+ status = acpi_enable_dpc_port(pdev, true);
+ if (status) {
+ pci_warn(pdev, "Enable DPC port failed\n");
+ acpi_remove_notify_handler(adev->handle,
+ ACPI_SYSTEM_NOTIFY,
+ edr_handle_event);
+ return status;
+ }
+
+ return 0;
+}
+
+void pci_acpi_remove_edr_notifier(struct pci_dev *pdev)
+{
+ struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
+
+ if (!adev)
+ return;
+
+ acpi_remove_notify_handler(adev->handle, ACPI_SYSTEM_NOTIFY,
+ edr_handle_event);
+}
diff --git a/include/linux/pci-acpi.h b/include/linux/pci-acpi.h
index 62b7fdcc661c..a430e5fc50f3 100644
--- a/include/linux/pci-acpi.h
+++ b/include/linux/pci-acpi.h
@@ -112,6 +112,14 @@ extern const guid_t pci_acpi_dsm_guid;
#define RESET_DELAY_DSM 0x08
#define FUNCTION_DELAY_DSM 0x09
+#ifdef CONFIG_PCIE_EDR
+int pci_acpi_add_edr_notifier(struct pci_dev *pdev);
+void pci_acpi_remove_edr_notifier(struct pci_dev *pdev);
+#else
+static inline int pci_acpi_add_edr_notifier(struct pci_dev *pdev) { return 0; }
+static inline void pci_acpi_remove_edr_notifier(struct pci_dev *pdev) { }
+#endif /* CONFIG_PCIE_EDR */
+
#else /* CONFIG_ACPI */
static inline void acpi_pci_add_bus(struct pci_bus *bus) { }
static inline void acpi_pci_remove_bus(struct pci_bus *bus) { }
--
2.21.0
--
Sathyanarayanan Kuppuswamy
Linux kernel developer
