RE: [PATCH v2 1/2] dt-bindings: PCI: designware: Add binding for ZRX-DC PHY property

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




> -----Original Message-----
> From: Andrew Murray <andrew.murray@xxxxxxx>
> Sent: Wednesday, November 6, 2019 3:24 PM
> To: Rob Herring <robh@xxxxxxxxxx>
> Cc: Anvesh Salveru <anvesh.s@xxxxxxxxxxx>; linux-pci@xxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> bhelgaas@xxxxxxxxxx; gustavo.pimentel@xxxxxxxxxxxx;
> jingoohan1@xxxxxxxxx; pankaj.dubey@xxxxxxxxxxx; Mark Rutland
> <mark.rutland@xxxxxxx>
> Subject: Re: [PATCH v2 1/2] dt-bindings: PCI: designware: Add binding for
ZRX-
> DC PHY property
> 
> On Tue, Nov 05, 2019 at 03:53:32PM -0600, Rob Herring wrote:
> > On Mon, Oct 28, 2019 at 05:46:27PM +0530, Anvesh Salveru wrote:
> > > Add support for ZRX-DC compliant PHYs. If PHY is not compliant to
> > > ZRX-DC specification, then after every 100ms link should transition
> > > to recovery state during the low power states which increases power
> consumption.
> > >
> > > Platforms with ZRX-DC compliant PHY can use "snps,phy-zrxdc-compliant"
> > > property in DesignWare controller DT node.
> > >
> > > CC: Rob Herring <robh+dt@xxxxxxxxxx>
> > > CC: Mark Rutland <mark.rutland@xxxxxxx>
> > > Signed-off-by: Anvesh Salveru <anvesh.s@xxxxxxxxxxx>
> > > Signed-off-by: Pankaj Dubey <pankaj.dubey@xxxxxxxxxxx>
> > > Reviewed-by: Gustavo Pimentel <gustavo.pimentel@xxxxxxxxxxxx>
> > > ---
> > > Change in v2: None
> > >
> > >  Documentation/devicetree/bindings/pci/designware-pcie.txt | 2 ++
> > >  1 file changed, 2 insertions(+)
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/pci/designware-pcie.txt
> > > b/Documentation/devicetree/bindings/pci/designware-pcie.txt
> > > index 78494c4050f7..9507ac38ac89 100644
> > > --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
> > > +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
> > > @@ -38,6 +38,8 @@ Optional properties:
> > >     for data corruption. CDM registers include standard PCIe
configuration
> > >     space registers, Port Logic registers, DMA and iATU (internal
Address
> > >     Translation Unit) registers.
> > > +- snps,phy-zrxdc-compliant: This property is needed if phy complies
> > > +with the
> > > +  ZRX-DC specification.
> >
> > If this is a property of the phy, then it belongs in the phy node or
> > should just be implied by the phy's compatible.
> 
Yes, from HW point of view this is a property of the PHY. As PHY is the one
which is ZRXDC compliant or non-compliant.  But as the DW controller
programming needs to be altered for handling such phys, so we added it as a
DT binding of DW controller driver.

We can't use PHY's compatible in case we want this to be in common code
(pcie-designware.c), as PHY compatible for each of the platform would be
different and PCIe DWC core file is not aware of this compatible. Of-course
this can be handled in platform specific driver, but then in that case each
of these drivers will add similar code to handle this.

> As suggested in the previous revision of this series [1], this is
absolutely a
> property of the phy.

Agreed, but as I tried to explain in series [1], this we are adding in
controller driver, as controller driver needs to program it's register based
on PHY HW property. 

> 
> > IOW, you should be able
> > to support this or not without changing DTs.
> >
> > Is this spec Synopys specific? (About the only thing Google turns up
> > are your patches.) If not, then probably shouldn't have a 'snps' prefix.
> 
> This was also unfamiliar to me, however my current understanding is that
Zrx-dc
> describes the 'Receiver DC single ended impedance' limits, this is
specified in the
> PCI specification (table 'Common Receiver Parameters'), with a different
limit
> for each speed.
> 
> I believe the purpose of this series is to to satisfy the following
implementation
> note in the spec "Ports that meet the Zrx-dc specification for 2.5 GT/s
while in
> the L1.Idle state are therefore not required to implement the 100 ms
timeout
> and transition to Recovery should avoid implementing it, since it will
reduce the
> power savings expected from the
> L1 state".
>

> In other words, if it is known that the phy is compliant then an
unnecessary
> transition to a higher energy state can be avoided. Though it's the PCI
controller
> (in this case) that must action this and must find out about the phy it is
> connected to.
>

Thanks, this is exactly the purpose of the patch. Currently this is being
handled in respective platform's driver, this patch intends to move this in
common code, where any platform driver using DesignWare controller can use
it without repeating same piece of code.
 
> So in my view 'phy-zrxdc-compliant' should be a property of a phy (without
snps
> prefix), and if a controller wants to determine if it is compliant then
there must
> be a phandle to the phy so the controller can find out.


Removing snps prefix, I am OK with it. But for moving this property to PHY
node, we need to find solution, how PCIe controller driver will access this
property of PHY device.
 
Platform driver which are using DesignWare controller driver has a phandle
to PHY, but question is here how does DesignWare controller driver will
infer this information from PHY driver. Some approaches which I can think of
are:
1) If PHY framework has some generic API to check if a particular property
exists in PHY node then it will be useful in such cases. Currently I don't
see any such API exists. Though I am not sure if it is OK to add such API in
PHY framework for such cases? Adding Kishon to comment on this.
2) Currently phandle to PHY is being stored as part of private data
structure of platform specific controller driver, and DesignWare core driver
can't access the phandle. So we need to move or keep copy of phandle pointer
to DesignWare core driver structure instead of keeping it in platform
specific private structure. 

I am open to any suggestion which can help us in keeping common piece of
code in DesignWare controller driver than repeating same in each and every
platform driver using DWC controller.


Thanks,
Pankaj Dubey

> 
> [1] https://patchwork.kernel.org/patch/11202121/
> 
> Thanks,
> 
> Andrew Murray
> 
> >
> > >  RC mode:
> > >  - num-viewport: number of view ports configured in hardware. If a
platform
> > >    does not specify it, the driver assumes 2.
> > > --
> > > 2.17.1
> > >




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux