Hi Andrey: Thanks a lot for your review comments. Best Regards Richard Zhu Office: 86-21-28937189 Mobile: 86-13386059786 > -----Original Message----- > From: Andrey Smirnov [mailto:andrew.smirnov@xxxxxxxxx] > Sent: 2019年3月14日 4:20 > To: Richard Zhu <hongxing.zhu@xxxxxxx> > Cc: bhelgaas@xxxxxxxxxx; lorenzo.pieralisi@xxxxxxx; > l.stach@xxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx; > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx > Subject: Re: [RFC 2/2] PCI: imx6: Add support for i.MX8QM/QXP PCIe > > On Wed, Mar 13, 2019 at 2:15 AM Richard Zhu <hongxing.zhu@xxxxxxx> > wrote: > > > > Add codes needed to support i.MX8QM/QXP PCIe. > > - HSIO(High Speed IO) subsystem is new defined on i.MX8QM/QXP. > > The PCIe and SATA modules are contained in the HSIO subsystem. There > > are two PCIe, one SATA controllers and three mixed lane PHYs on > > i.MX8QM. There are three use cases of the HSIO subsystem on > i.MX8QM. > > 1. PCIea 2 lanes and one SATA AHCI port. > > 2. PCIea 1 lane, PCIeb 1 lane and one SATA AHCI port. > > 3. PCIea 2 lanes, PCIeb 1 lane. > > i.MX8QXP only has PCIeb controller and one lane PHY. > > - The HSIO address map as viewed from system level is as shown below. > > address [31:24] Local address Target Address Size > > 5F 0 HSIO 16MB > > 60-6F 40-4F HSIO 256MB > > 70-7F 80-8F HSIO 256MB > > So, the cpu_addr_fixup is required to enable i.MX8QM/QXP PCIe. > > - Both external OSC and internal PLL can be used as PCIe reference > > clock. > > - clock request GPIO for controlling the PCI reference clock request > > signal. And should be configure OD when L1SS maybe enabled later. > > - One more power domain HSIO_GPIO and clock PCIE_PER are required by > > i.MX8QM/QXP PCIe. > > > > Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx> > > --- > > drivers/pci/controller/dwc/pci-imx6.c | 392 > > +++++++++++++++++++++++++++++++++- > > 1 file changed, 387 insertions(+), 5 deletions(-) > > > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c > > b/drivers/pci/controller/dwc/pci-imx6.c > > index aaa9489..aacefb6 100644 > > --- a/drivers/pci/controller/dwc/pci-imx6.c > > +++ b/drivers/pci/controller/dwc/pci-imx6.c > > @@ -39,6 +39,7 @@ > > #define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE BIT(11) > > #define IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE GENMASK(11, > 8) > > #define IMX8MQ_PCIE2_BASE_ADDR 0x33c00000 > > +#define IMX8_HSIO_PCIEB_BASE_ADDR 0x5f010000 > > > > #define to_imx6_pcie(x) dev_get_drvdata((x)->dev) > > > > @@ -48,10 +49,13 @@ enum imx6_pcie_variants { > > IMX6QP, > > IMX7D, > > IMX8MQ, > > + IMX8QM, > > + IMX8QXP, > > }; > > > > #define IMX6_PCIE_FLAG_IMX6_PHY BIT(0) > > #define IMX6_PCIE_FLAG_IMX6_SPEED_CHANGE BIT(1) > > +#define IMX6_PCIE_FLAG_IMX6_CPU_ADDR_FIXUP BIT(2) > > This is an IMX8Q* specific flag, so it probably should be called something like > IMX6_PCIE_FLAG_IMX8Qx_CPU_ADD_FIXUP. [Richard Zhu] Okay, would change it later. > > > > > struct imx6_pcie_drvdata { > > enum imx6_pcie_variants variant; @@ -60,10 +64,12 @@ struct > > imx6_pcie_drvdata { > > > > struct imx6_pcie { > > struct dw_pcie *pci; > > + int clkreq_gpio; > > Is this really necessary? On i.MX8MQ vendor tree for some unknown reason > would reconfigure a dedicated CLKREQ_B signal as a GPIO and then use it as > CLKREQ signal that way instead of controlling it via dedicated bits in register > file, so I am wondering if that is the case with QM and QXP. [Richard Zhu] There is a same mechanism of the CLKREQ on iMX8QM/QXP/MQ. Up to now, this pin is configured as GPIO, because that this pin would be pull up when OD is set and the EP device doesn't support the L1SS at all. Thus, the external CLK would be turned off in this scenario. This pin would be used in OD(Open Drain) mode when L1SS is enabled. The L1SS has been verified on iMX8MQ. But I don't have a dynamic method to turn the L1SS feature on at RC side yet when the L1SS is supported by EP. Configure CLK_REQ as GPIO here currently, and hope to figure out one solution in future. > > > int reset_gpio; > > bool gpio_active_high; > > struct clk *pcie_bus; > > struct clk *pcie_phy; > > + struct clk *pcie_per; > > struct clk *pcie_inbound_axi; > > struct clk *pcie; > > struct clk *pcie_aux; > > @@ -77,6 +83,9 @@ struct imx6_pcie { > > u32 tx_deemph_gen2_6db; > > u32 tx_swing_full; > > u32 tx_swing_low; > > + u32 hsio_cfg; > > + u32 ext_osc; > > + u32 local_addr; > > int link_gen; > > struct regulator *vpcie; > > void __iomem *phy_base; > > @@ -85,6 +94,8 @@ struct imx6_pcie { > > struct device *pd_pcie; > > /* power domain for pcie phy */ > > struct device *pd_pcie_phy; > > + /* power domain for hsio gpio used by pcie */ > > + struct device *pd_hsio_gpio; > > const struct imx6_pcie_drvdata *drvdata; }; > > > > @@ -92,6 +103,7 @@ struct imx6_pcie { > > #define PHY_PLL_LOCK_WAIT_MAX_RETRIES 2000 > > #define PHY_PLL_LOCK_WAIT_USLEEP_MIN 50 > > #define PHY_PLL_LOCK_WAIT_USLEEP_MAX 200 > > +#define L2_ENTRY_WAIT_MAX_RETRIES 10000 > > > > /* PCIe Root Complex registers (memory-mapped) */ > > #define PCIE_RC_IMX6_MSI_CAP 0x50 > > @@ -157,6 +169,43 @@ struct imx6_pcie { #define > > PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5) #define > > PHY_RX_OVRD_IN_LO_RX_PLL_EN (1 << 3) > > > > +/* iMX8 HSIO registers */ > > +#define IMX8QM_CSR_PHYX2_OFFSET > 0x00000 > > +#define IMX8QM_CSR_PHYX1_OFFSET > 0x10000 > > +#define IMX8QM_CSR_PHYX_STTS0_OFFSET 0x4 > > +#define IMX8QM_CSR_PCIEA_OFFSET > 0x20000 > > +#define IMX8QM_CSR_PCIEB_OFFSET > 0x30000 > > +#define IMX8QM_CSR_PCIE_CTRL1_OFFSET 0x4 > > +#define IMX8QM_CSR_PCIE_CTRL2_OFFSET 0x8 > > +#define IMX8QM_CSR_PCIE_STTS0_OFFSET 0xC > > +#define IMX8QM_CSR_MISC_OFFSET 0x50000 > > + > > +#define IMX8QM_CTRL_LTSSM_ENABLE BIT(4) > > +#define IMX8QM_CTRL_READY_ENTR_L23 BIT(5) > > +#define IMX8QM_CTRL_PM_XMT_TURNOFF BIT(9) > > +#define IMX8QM_CTRL_BUTTON_RST_N BIT(21) > > +#define IMX8QM_CTRL_PERST_N BIT(22) > > +#define IMX8QM_CTRL_POWER_UP_RST_N BIT(23) > > + > > +#define IMX8QM_CTRL_STTS0_PM_LINKST_IN_L2 BIT(13) > > +#define IMX8QM_CTRL_STTS0_PM_REQ_CORE_RST BIT(19) > > +#define IMX8QM_STTS0_LANE0_TX_PLL_LOCK BIT(4) > > +#define IMX8QM_STTS0_LANE1_TX_PLL_LOCK BIT(12) > > + > > +#define IMX8QM_PCIE_TYPE_MASK GENMASK(27, > 24) > > + > > +#define IMX8QM_PHYX2_CTRL0_APB_MASK GENMASK(1, > 0) > > +#define IMX8QM_PHY_APB_RSTN_0 BIT(0) > > +#define IMX8QM_PHY_APB_RSTN_1 BIT(1) > > + > > +#define IMX8QM_MISC_IOB_RXENA BIT(0) > > +#define IMX8QM_MISC_IOB_TXENA BIT(1) > > +#define IMX8QM_CSR_MISC_IOB_A_0_TXOE BIT(2) > > +#define IMX8QM_CSR_MISC_IOB_A_0_M1M0_MASK GENMASK(4, > 3) > > +#define IMX8QM_CSR_MISC_IOB_A_0_M1M0_2 BIT(4) > > +#define IMX8QM_MISC_PHYX1_EPCS_SEL BIT(12) > > +#define IMX8QM_MISC_PCIE_AB_SELECT BIT(13) > > + > > static int pcie_phy_poll_ack(struct imx6_pcie *imx6_pcie, int > > exp_val) { > > struct dw_pcie *pci = imx6_pcie->pci; @@ -373,14 +422,65 @@ > > static int imx6_pcie_attach_pd(struct device *dev) > > return PTR_ERR(link); > > } > > > > + switch (imx6_pcie->drvdata->variant) { > > + case IMX8QM: > > + case IMX8QXP: > > + imx6_pcie->pd_hsio_gpio = > dev_pm_domain_attach_by_name(dev, > > + "hsio_gpio"); > > + if (IS_ERR(imx6_pcie->pd_hsio_gpio)) > > + return PTR_ERR(imx6_pcie->pd_hsio_gpio); > > + > > + link = device_link_add(dev, imx6_pcie->pd_hsio_gpio, > > + DL_FLAG_STATELESS | > > + DL_FLAG_PM_RUNTIME | > > + DL_FLAG_RPM_ACTIVE); > > + if (!link) { > > + dev_err(dev, "Failed to add device_link to gpio > pd.\n"); > > + return -EINVAL; > > + } > > + > > + break; > > + default: > > + break; > > + } > > + > > return 0; > > } > > > > static void imx6_pcie_assert_core_reset(struct imx6_pcie *imx6_pcie) > > { > > + u32 addr; > > + int i; > > struct device *dev = imx6_pcie->pci->dev; > > > > switch (imx6_pcie->drvdata->variant) { > > + case IMX8QXP: > > + addr = IMX8QM_CSR_PCIEB_OFFSET + > > + IMX8QM_CSR_PCIE_CTRL2_OFFSET; > > This and similar "IMX8QM_CSR_PCIEA_OFFSET + i * SZ_64K" pattern keeps > popping up quite frequently in the code. I think at the very least it would be > good to calculate this offset in probe and store it as a member of struct > imx6_pcie. However I do wonder if this should actually be handle by either > declaring an additional syscon regmap of additional reg/reg-name property. > [Richard Zhu] IMHO, I just reduce some more MACRO definitions in the codes. Actually, the "IMX8QM_CSR_PCIEA_OFFSET + SZ_64K" should be the IMX8QM_CSR_PCIEB_OFFSET. I can add some more macro-definitions, for example " IMX8QM_CSR_PCIEB_OFFSET " to remove the calculations later. How do you think about that? > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, addr, > > + IMX8QM_CTRL_BUTTON_RST_N, > > + IMX8QM_CTRL_BUTTON_RST_N); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, addr, > > + IMX8QM_CTRL_PERST_N, > > + IMX8QM_CTRL_PERST_N); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, addr, > > + > IMX8QM_CTRL_POWER_UP_RST_N, > > + > IMX8QM_CTRL_POWER_UP_RST_N); > > + break; > > + case IMX8QM: > > + for (i = 0; i <= imx6_pcie->controller_id; i++) { > > This loop is a bit surprising to me. It's hard to tell why you'd iterate from 0 to > controller_id. I think it'd be good to add a comment explaining the logic > behind this code. > [Richard Zhu] Okay, comments would be added here. /* * In i.MX8QM, two lanes PHY and one lane PHY share the * same calibration signal. And one lane PHY would use * the calibration output from two lanes PHY. So PCIeA * related resets are configured before configurating PCIeB. */ > > > + addr = IMX8QM_CSR_PCIEA_OFFSET + i * > SZ_64K; > > + addr += IMX8QM_CSR_PCIE_CTRL2_OFFSET; > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > addr, > > + > IMX8QM_CTRL_BUTTON_RST_N, > > + > IMX8QM_CTRL_BUTTON_RST_N); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > addr, > > + > IMX8QM_CTRL_PERST_N, > > + > IMX8QM_CTRL_PERST_N); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > addr, > > + > IMX8QM_CTRL_POWER_UP_RST_N, > > + > IMX8QM_CTRL_POWER_UP_RST_N); > > + } > > + break; > > case IMX7D: > > case IMX8MQ: > > reset_control_assert(imx6_pcie->pciephy_reset); > > @@ -477,6 +577,21 @@ static int imx6_pcie_enable_ref_clk(struct > imx6_pcie *imx6_pcie) > > > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN, > > > IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN); > > break; > > + case IMX8QXP: > > + case IMX8QM: > > + ret = > clk_prepare_enable(imx6_pcie->pcie_inbound_axi); > > + if (ret) { > > + dev_err(dev, "unable to enable pcie_axi > clock\n"); > > + break; > > + } > > + ret = clk_prepare_enable(imx6_pcie->pcie_per); > > + if (ret) { > > + dev_err(dev, "unable to enable pcie_per > clock\n"); > > + > clk_disable_unprepare(imx6_pcie->pcie_inbound_axi); > > + break; > > + } > > + > > + break; > > } > > > > return ret; > > @@ -501,6 +616,63 @@ static void > imx7d_pcie_wait_for_phy_pll_lock(struct imx6_pcie *imx6_pcie) > > dev_err(dev, "PCIe PLL lock timeout\n"); } > > > > +static int imx8_hsio_pcie_wait_for_phy_pll_lock(struct imx6_pcie > > +*imx6_pcie) { > > + u32 retries, addr, val, lock = 0; > > + int ret; > > + struct dw_pcie *pci = imx6_pcie->pci; > > + struct device *dev = pci->dev; > > + > > + addr = IMX8QM_CSR_PCIEA_OFFSET + imx6_pcie->controller_id > * SZ_64K; > > + addr += IMX8QM_CSR_PCIE_STTS0_OFFSET; > > + for (retries = 0; retries < PHY_PLL_LOCK_WAIT_MAX_RETRIES; > retries++) { > > + regmap_read(imx6_pcie->iomuxc_gpr, addr, &val); > > + if ((val & IMX8QM_CTRL_STTS0_PM_REQ_CORE_RST) > == 0) > > + break; > > + udelay(1); > > + } > > + > > + if ((val & IMX8QM_CTRL_STTS0_PM_REQ_CORE_RST) != 0) { > > + dev_err(dev, "ERROR: PM_REQ_CORE_RST is still > set.\n"); > > + return -ENODEV; > > + } > > + > > You can really cut down on boilerplate here by using > regmap_read_poll_timeout() > [Richard Zhu] Okay, would change it later. > > + addr = IMX8QM_CSR_PHYX2_OFFSET + imx6_pcie->controller_id > * SZ_64K; > > + addr += IMX8QM_CSR_PHYX_STTS0_OFFSET; > > + for (retries = 0; retries < PHY_PLL_LOCK_WAIT_MAX_RETRIES; > retries++) { > > + regmap_read(imx6_pcie->iomuxc_gpr, addr, &val); > > + if (imx6_pcie->hsio_cfg == 2) { > > + if (imx6_pcie->controller_id == 0) > > + lock = > IMX8QM_STTS0_LANE0_TX_PLL_LOCK; > > + else > > + lock = > IMX8QM_STTS0_LANE1_TX_PLL_LOCK; > > + } else if (imx6_pcie->hsio_cfg == 3) { > > + lock = > IMX8QM_STTS0_LANE0_TX_PLL_LOCK; > > + if (imx6_pcie->controller_id == 0) > > + lock |= > IMX8QM_STTS0_LANE1_TX_PLL_LOCK; > > + } else if (imx6_pcie->hsio_cfg == 1) { > > + lock = > IMX8QM_STTS0_LANE0_TX_PLL_LOCK; > > + lock |= > IMX8QM_STTS0_LANE1_TX_PLL_LOCK; > > + } else { > > + dev_err(dev, "ERROR: illegal hsio_cfg > value.\n"); > > + return -EINVAL; > > + } > > + val &= lock; > > + if (val == lock) > > + break; > > + udelay(10); > > + } > > + > > + if (retries >= PHY_PLL_LOCK_WAIT_MAX_RETRIES) { > > + dev_info(dev, "pcie phy pll can't be locked.\n"); > > + ret = -ENODEV; > > + } else { > > + dev_info(dev, "pcie phy pll is locked.\n"); > > + } > > + > > Ditto. [Richard Zhu] Got that. Thanks. > > > + return ret; > > +} > > + > > static void imx6_pcie_deassert_core_reset(struct imx6_pcie > > *imx6_pcie) { > > struct dw_pcie *pci = imx6_pcie->pci; @@ -553,6 +725,11 @@ > > static void imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie) > > } > > > > switch (imx6_pcie->drvdata->variant) { > > + case IMX8QXP: > > + case IMX8QM: > > + /* wait for phy pll lock firstly. */ > > + imx8_hsio_pcie_wait_for_phy_pll_lock(imx6_pcie); > > + break; > > case IMX8MQ: > > reset_control_deassert(imx6_pcie->pciephy_reset); > > break; > > @@ -613,25 +790,114 @@ static void > > imx6_pcie_deassert_core_reset(struct imx6_pcie *imx6_pcie) > > > > static void imx6_pcie_configure_type(struct imx6_pcie *imx6_pcie) { > > - unsigned int mask, val; > > - > > - if (imx6_pcie->drvdata->variant == IMX8MQ && > > + unsigned int offset, mask, val; > > + > > + if (imx6_pcie->drvdata->variant == IMX8QM || > > + imx6_pcie->drvdata->variant == IMX8QXP) { > > Since there's now more than two possibilities, it'd probably make sense to > convert this code to use switch statement. [Richard Zhu] Okay, would use switch statement later. > > > + offset = IMX8QM_CSR_PCIEA_OFFSET + > > + imx6_pcie->controller_id * SZ_64K; > > + mask = IMX8QM_PCIE_TYPE_MASK; > > + val = FIELD_PREP(IMX8QM_PCIE_TYPE_MASK, > > + PCI_EXP_TYPE_ROOT_PORT); > > + } else if (imx6_pcie->drvdata->variant == IMX8MQ && > > imx6_pcie->controller_id == 1) { > > + offset = IOMUXC_GPR12; > > mask = > IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE; > > val = > FIELD_PREP(IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE, > > PCI_EXP_TYPE_ROOT_PORT); > > } else { > > + offset = IOMUXC_GPR12; > > mask = IMX6Q_GPR12_DEVICE_TYPE; > > val = FIELD_PREP(IMX6Q_GPR12_DEVICE_TYPE, > > PCI_EXP_TYPE_ROOT_PORT); > > } > > > > - regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, > mask, val); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, offset, mask, val); > > } > > > > static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie) { > > switch (imx6_pcie->drvdata->variant) { > > + case IMX8QXP: > > + case IMX8QM: > > + if (imx6_pcie->hsio_cfg == 1) { > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_PHYX2_OFFSET, > > + > IMX8QM_PHYX2_CTRL0_APB_MASK, > > + IMX8QM_PHY_APB_RSTN_0 | > > + IMX8QM_PHY_APB_RSTN_1); > > + > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_PHYX1_EPCS_SEL, > > + IMX8QM_MISC_PHYX1_EPCS_SEL); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_PCIE_AB_SELECT, > > + 0); > > + } else if (imx6_pcie->hsio_cfg == 2) { > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_PHYX2_OFFSET, > > + > IMX8QM_PHYX2_CTRL0_APB_MASK, > > + IMX8QM_PHY_APB_RSTN_0 | > > + IMX8QM_PHY_APB_RSTN_1); > > + > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_PHYX1_EPCS_SEL, > > + IMX8QM_MISC_PHYX1_EPCS_SEL); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_PCIE_AB_SELECT, > > + IMX8QM_MISC_PCIE_AB_SELECT); > > + } else if (imx6_pcie->hsio_cfg == 3) { > > + if (imx6_pcie->controller_id) > > + > regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + > IMX8QM_CSR_PHYX1_OFFSET, > > + > IMX8QM_PHY_APB_RSTN_0, > > + > IMX8QM_PHY_APB_RSTN_0); > > + else > > + > regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + > IMX8QM_CSR_PHYX2_OFFSET, > > + > IMX8QM_PHYX2_CTRL0_APB_MASK, > > + > IMX8QM_PHY_APB_RSTN_0 | > > + > IMX8QM_PHY_APB_RSTN_1); > > + > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_PHYX1_EPCS_SEL, > 0); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_PCIE_AB_SELECT, > > + IMX8QM_MISC_PCIE_AB_SELECT); > > + } > > + > > This doesn't look controller independent/local. What would happen if > controller 0 specifies hsio_cfg == 2 and controller 1 specifies hsio_cfg == 1? > [Richard Zhu]Yes, it is. There are usage dependences between PCIeA/PCIeB and SATA in HSIO subsystem. BTW, It's impossible for controller 1 to specify the hsio_cfg to "1", when controller 0 specifies hsio_cfg==2. There are three usage cases of the HSIO. Hsio_cfg pciea pcieb sata 1 2lanes No Enabled 2 1lane 1lane Enabled 3 2lanes 1lane No So, the possible hsio_cfg values for PCIeB is 2 or 3. > > + if (imx6_pcie->ext_osc) { > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_IOB_RXENA, > > + IMX8QM_MISC_IOB_RXENA); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_IOB_TXENA, 0); > > + } else { > > + /* Try to used the internal pll as ref clk */ > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_IOB_RXENA, 0); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + IMX8QM_MISC_IOB_TXENA, > > + IMX8QM_MISC_IOB_TXENA); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + IMX8QM_CSR_MISC_OFFSET, > > + > IMX8QM_CSR_MISC_IOB_A_0_TXOE | > > + > IMX8QM_CSR_MISC_IOB_A_0_M1M0_MASK, > > + > IMX8QM_CSR_MISC_IOB_A_0_TXOE | > > + > IMX8QM_CSR_MISC_IOB_A_0_M1M0_2); > > + } > > Same here. It looks like specifying "ext_osc" for one controller and leaving it > out for another would lead to different outcome based on which controller > gets initialized first. > > It seems that maybe abstracting all of this away via a generic PHY subsystem > would be a better path. See for example pci-dra7xx.c which looks like it might > be a good example. > [Richard Zhu] Okay, would following your suggestions. Thanks a lot. > > + > > + break; > > case IMX8MQ: > > /* > > * TODO: Currently this code assumes external @@ > > -763,6 +1029,7 @@ static int imx6_pcie_wait_for_speed_change(struct > > imx6_pcie *imx6_pcie) > > > > static void imx6_pcie_ltssm_enable(struct device *dev) { > > + u32 val; > > struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); > > > > switch (imx6_pcie->drvdata->variant) { @@ -777,6 +1044,15 > @@ > > static void imx6_pcie_ltssm_enable(struct device *dev) > > case IMX8MQ: > > reset_control_deassert(imx6_pcie->apps_reset); > > break; > > + case IMX8QXP: > > + case IMX8QM: > > + val = IMX8QM_CSR_PCIEA_OFFSET + > > + imx6_pcie->controller_id * SZ_64K; > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + val + > IMX8QM_CSR_PCIE_CTRL2_OFFSET, > > + IMX8QM_CTRL_LTSSM_ENABLE, > > + IMX8QM_CTRL_LTSSM_ENABLE); > > + break; > > } > > } > > > > @@ -908,13 +1184,25 @@ static int imx6_add_pcie_port(struct imx6_pcie > *imx6_pcie, > > return 0; > > } > > > > +static u64 imx6_pcie_cpu_addr_fixup(struct dw_pcie *pcie, u64 > > +cpu_addr) { > > + struct pcie_port *pp = &pcie->pp; > > + struct imx6_pcie *imx6_pcie = to_imx6_pcie(pcie); > > + > > + if (imx6_pcie->drvdata->flags & > IMX6_PCIE_FLAG_IMX6_CPU_ADDR_FIXUP) > > + return (cpu_addr + imx6_pcie->local_addr - > > + pp->mem_base); > > If you do > > cpu_addr += mx6_pcie->local_addr - pp->mem_base; > > you won't need an else below. > [Richard Zhu] You're right. Thanks. > > + else > > + return cpu_addr; > > +} > > + > > static const struct dw_pcie_ops dw_pcie_ops = { > > - /* No special ops needed, but pcie-designware still expects this > struct */ > > + .cpu_addr_fixup = imx6_pcie_cpu_addr_fixup, > > }; > > > > #ifdef CONFIG_PM_SLEEP > > static void imx6_pcie_ltssm_disable(struct device *dev) { > > + u32 val; > > struct imx6_pcie *imx6_pcie = dev_get_drvdata(dev); > > > > switch (imx6_pcie->drvdata->variant) { @@ -926,6 +1214,17 > @@ > > static void imx6_pcie_ltssm_disable(struct device *dev) > > case IMX7D: > > reset_control_assert(imx6_pcie->apps_reset); > > break; > > + case IMX8QXP: > > + case IMX8QM: > > + val = IMX8QM_CSR_PCIEA_OFFSET + > > + imx6_pcie->controller_id * SZ_64K; > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + val + > IMX8QM_CSR_PCIE_CTRL2_OFFSET, > > + IMX8QM_CTRL_LTSSM_ENABLE, 0); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + val + > IMX8QM_CSR_PCIE_CTRL2_OFFSET, > > + IMX8QM_CTRL_READY_ENTR_L23, > 0); > > + break; > > default: > > dev_err(dev, "ltssm_disable not supported\n"); > > } > > @@ -933,6 +1232,8 @@ static void imx6_pcie_ltssm_disable(struct device > > *dev) > > > > static void imx6_pcie_pm_turnoff(struct imx6_pcie *imx6_pcie) { > > + int i; > > + u32 addr, val; > > struct device *dev = imx6_pcie->pci->dev; > > > > /* Some variants have a turnoff reset in DT */ @@ -951,6 > > +1252,34 @@ static void imx6_pcie_pm_turnoff(struct imx6_pcie > *imx6_pcie) > > regmap_update_bits(imx6_pcie->iomuxc_gpr, > IOMUXC_GPR12, > > > IMX6SX_GPR12_PCIE_PM_TURN_OFF, 0); > > break; > > + case IMX8QXP: > > + case IMX8QM: > > + addr = IMX8QM_CSR_PCIEA_OFFSET + > > + imx6_pcie->controller_id * SZ_64K; > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + addr + > IMX8QM_CSR_PCIE_CTRL2_OFFSET, > > + > IMX8QM_CTRL_PM_XMT_TURNOFF, > > + > IMX8QM_CTRL_PM_XMT_TURNOFF); > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + addr + > IMX8QM_CSR_PCIE_CTRL2_OFFSET, > > + > IMX8QM_CTRL_PM_XMT_TURNOFF, 0); > > Is setting IMX8QM_CTRL_PM_XMT_TURNOFF on and then off necessary? I'd > add a comment to highlight that this is intentional. > [Richard Zhu] Designer suggest to do so. One PME message would be kicked off on the link after these turn on/off operations. > > + regmap_update_bits(imx6_pcie->iomuxc_gpr, > > + addr + > IMX8QM_CSR_PCIE_CTRL2_OFFSET, > > + IMX8QM_CTRL_READY_ENTR_L23, > > + > IMX8QM_CTRL_READY_ENTR_L23); > > + /* check the L2 is entered or not. */ > > + for (i = 0; i < L2_ENTRY_WAIT_MAX_RETRIES; i++) { > > + regmap_read(imx6_pcie->iomuxc_gpr, > > + addr + > IMX8QM_CSR_PCIE_STTS0_OFFSET, > > + &val); > > + if (val & > IMX8QM_CTRL_STTS0_PM_LINKST_IN_L2) > > + break; > > + udelay(10); > > + } > > + if ((val & IMX8QM_CTRL_STTS0_PM_LINKST_IN_L2) == > 0) > > + dev_err(dev, "PCIE%d can't enter into L2.\n", > > + > imx6_pcie->controller_id); > > regmap_read_poll_timeout() > [Richard Zhu] Okay, would use regmap_read_poll_timeout() in next version. > > + break; > > default: > > dev_err(dev, "PME_Turn_Off not implemented\n"); > > return; > > @@ -985,6 +1314,11 @@ static void imx6_pcie_clk_disable(struct > imx6_pcie *imx6_pcie) > > case IMX8MQ: > > clk_disable_unprepare(imx6_pcie->pcie_aux); > > break; > > + case IMX8QXP: > > + case IMX8QM: > > + clk_disable_unprepare(imx6_pcie->pcie_per); > > + clk_disable_unprepare(imx6_pcie->pcie_inbound_axi); > > You can probably piggy back on IMX6SX since it has "pcie_inbound_axi" as > well. > [Richard Zhu] Okay, would follow your suggestion. Thanks. Would change like below. case IMX8QXP: case IMX8QM: clk_disable_unprepare(imx6_pcie->pcie_per); case IMX6SX: clk_disable_unprepare(imx6_pcie->pcie_inbound_axi); break; > > + break; > > default: > > break; > > } > > @@ -1084,7 +1418,26 @@ static int imx6_pcie_probe(struct > platform_device *pdev) > > if (IS_ERR(pci->dbi_base)) > > return PTR_ERR(pci->dbi_base); > > > > + if (of_property_read_u32(node, "hsio-cfg", > &imx6_pcie->hsio_cfg)) > > + imx6_pcie->hsio_cfg = 0; > > + if (of_property_read_u32(node, "ext_osc", &imx6_pcie->ext_osc) > < 0) > > + imx6_pcie->ext_osc = 0; > > + if (of_property_read_u32(node, "local-addr", > &imx6_pcie->local_addr)) > > + imx6_pcie->local_addr = 0; > > All of these properties will be initialized to zero by kzalloc and > of_property_read_u32() won't modify output variable unless it is successful, > so you can probably skip error checking. [Richard Zhu] Okay, would remove the error checking. > > > + > > /* Fetch GPIOs */ > > + imx6_pcie->clkreq_gpio = of_get_named_gpio(node, "clkreq-gpio", > 0); > > + if (gpio_is_valid(imx6_pcie->clkreq_gpio)) { > > + ret = devm_gpio_request_one(&pdev->dev, > imx6_pcie->clkreq_gpio, > > + > GPIOF_OUT_INIT_LOW, "PCIe CLKREQ"); > > + if (ret) { > > + dev_err(&pdev->dev, "unable to get clkreq > gpio\n"); > > + return ret; > > + } > > + } else if (imx6_pcie->clkreq_gpio == -EPROBE_DEFER) { > > + return imx6_pcie->clkreq_gpio; > > + } > > + > > imx6_pcie->reset_gpio = of_get_named_gpio(node, "reset-gpio", > 0); > > imx6_pcie->gpio_active_high = of_property_read_bool(node, > > > > "reset-gpio-active-high"); @@ -1155,6 +1508,25 @@ static int > imx6_pcie_probe(struct platform_device *pdev) > > return PTR_ERR(imx6_pcie->pcie_aux); > > } > > break; > > + case IMX8QM: > > + case IMX8QXP: > > + if (dbi_base->start == IMX8_HSIO_PCIEB_BASE_ADDR) > > + imx6_pcie->controller_id = 1; > > + > > + imx6_pcie->pcie_per = devm_clk_get(dev, "pcie_per"); > > + if (IS_ERR(imx6_pcie->pcie_per)) { > > + dev_err(dev, "pcie_per clock source missing > or invalid\n"); > > + return PTR_ERR(imx6_pcie->pcie_per); > > + } > > + > > + imx6_pcie->pcie_inbound_axi = > devm_clk_get(&pdev->dev, > > + "pcie_inbound_axi"); > > + if (IS_ERR(imx6_pcie->pcie_inbound_axi)) { > > + dev_err(&pdev->dev, > > + "pcie clock source missing or > invalid\n"); > > + return > PTR_ERR(imx6_pcie->pcie_inbound_axi); > > + } > > On i.MX8MQ "pcie_bus" clock in vendor tree wasn't actually pointing to > actual PCIE bus clock, so it might be worth checking if that's the case for > i.MX8QM/X and you actually need one more clock. [Richard Zhu] Regarding to my understanding, iMX PCIe module is connected to AXI bus. Thus, the AXI related clock can be treated as bus clock. Correct me if my understand is wrong. So, I use the pcie_bus clock for i.MX8QM/QXP PCIe in the dts binding. Otherwise, I can use another new clock in codes to support i.MX8QM/QXP PCIes. Thanks a lot for your kindly review. > > Thanks, > Andrey Smirnov
