Hi Thomas,
On 2019-02-12 13:41, Thomas Petazzoni wrote:
Hello Leigh,
On Thu, 31 Jan 2019 16:06:10 +0000
Leigh Brown <leigh@xxxxxxxxxxxxx> wrote:
Thanks for responding. I had to manually apply the patch, but it
certainly fixes the issue.
Could you check if the branch at:
https://github.com/tpetazzoni/linux/tree/5.0/marvell/pci-mvebu-fix
also fixes the issue for you ?
I'm sorry to ask you to do all those tests, but since I don't have a
PCIe device that uses prefetchable memory BARs, I can't test :-/
Thanks!
Thomas
It seems to work perfectly now, thanks. Boot log attached.
Regards,
Leigh.
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
Detected Device ID 6820
High speed PHY - Version: 2.0
Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 06 | SATA0 |
| 1 | 05 | PCIe0 |
| 2 | 06 | SATA1 |
| 3 | 05 | USB3 HOST1 |
| 4 | 05 | PCIe1 |
| 5 | 00 | SGMII2 |
--------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.26.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01 (Mar 27 2015 - 16:50:46) Marvell version: 2014_T3.0p6
Boot version : v1.0.13
Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1600 [MHz]
L2 @ 800 [MHz]
TClock @ 200 [MHz]
DDR @ 800 [MHz]
DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
Map: Code: 0x1fea9000:0x1ff7632c
BSS: 0x1ffef6b4
Stack: 0x1f9a8f20
Heap: 0x1f9a9000:0x1fea9000
raise: Signal # 8 caught
U-ENV offset == 0x200000
raise: Signal # 8 caught
U-ENV offset == 0x200000
U-Boot Environment: 0x00200000:0x00220000 (NAND)
NAND: 128 MiB
MMC: mv_sdh: 0
DEVINFO offset == 0x900000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
S-ENV offset == 0x240000
#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3
S-ENV offset == 0x240000
[boot_count_read] block:0x240000, size:128KB, records:64
[boot_count_read_record] boot_count:2, next_record:26
[boot_count_write] erase:0, auto_recovery->block_offset:0x240000 offset=0x24D000
Updating boot_count ...
[boot_count_write] offset:0x24D000 , length:2048
done
PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode
Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
egiga0 [PRIME], egiga1
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv bootargs console=ttyS0,115200 root=/dev/sda2 rootdelay=2
Marvell>> fatload usb 0 0x6400000 uImage-5.0.0-rc6
reading uImage-5.0.0-rc6
2713748 bytes read in 110 ms (23.5 MiB/s)
Marvell>> fatload usb 0 0x7400000 uInitrd-5.0.0-rc6
reading uInitrd-5.0.0-rc6
1690436 bytes read in 85 ms (19 MiB/s)
Marvell>> bootm 0x6400000 0x7400000
## Booting kernel from Legacy Image at 06400000 ...
Image Name: uImage-5.0.0-rc6
Created: 2019-02-12 16:02:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2713684 Bytes = 2.6 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 07400000 ...
Image Name: uInitrd-5.0.0-rc6
Created: 2019-02-12 16:02:22 UTC
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 1690372 Bytes = 1.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 5.0.0-rc6 (leigh@dish) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #2 SMP Tue Feb 12 15:04:14 GMT 2019
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=50c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: Linksys WRT1900ACS
Memory policy: Data cache writealloc
random: get_random_bytes called from start_kernel+0x55/0x2d8 with crng_init=0
percpu: Embedded 16 pages/cpu @(ptrval) s34508 r8192 d22836 u65536
Built 1 zonelists, mobility grouping on. Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootdelay=2
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510420K/524288K available (4096K kernel code, 211K rwdata, 1064K rodata, 1024K init, 117K bss, 13868K reserved, 0K cma-reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
lowmem : 0xb0000000 - 0xd0000000 ( 512 MB)
modules : 0xaf800000 - 0xb0000000 ( 8 MB)
.text : 0x(ptrval) - 0x(ptrval) (5088 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 212 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 118 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 D prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns
Switching to timer-based delay loop, resolution 1ns
Ignoring duplicate/late registration of read_current_timer delay
clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.00 BogoMIPS (lpj=8000000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100054
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
mvebu-pmsu: Initializing Power Management Service Unit
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs ...
Booting CPU 1
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (3200.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
cryptd: max_cpu_qlen set to 1000
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 1652K
Initialise system trusted keyrings
workingset: timestamp_bits=30 max_order=17 bucket_order=0
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers disabled
pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:02.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
PCI: bus2: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe01fffff]
pci 0000:00:02.0: BAR 8: assigned [mem 0xe0200000-0xe03fffff]
pci 0000:00:01.0: BAR 6: assigned [mem 0xe0400000-0xe04007ff pref]
pci 0000:00:02.0: BAR 6: assigned [mem 0xe0500000-0xe05007ff pref]
pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0xe0100000-0xe01fffff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe01fffff]
pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0xe0300000-0xe03fffff 64bit pref]
pci 0000:00:02.0: PCI bridge to [bus 02]
pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe03fffff]
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
printk: console [ttyS0] disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A
printk: console [ttyS0] enabled
ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi host0: ahci-mvebu
scsi host1: ahci-mvebu
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
libphy: Fixed MDIO Bus: probed
libphy: orion_mdio_bus: probed
mv88e6085 f1072004.mdio-mii:00: switch 0x1760 detected: Marvell 88E6176, revision 1
libphy: mv88e6xxx SMI: probed
mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
mvneta f1070000.ethernet eth0: Using hardware mac address 58:ef:68:a5:f2:da
mvneta f1034000.ethernet eth1: Using random mac address 1e:b4:e6:ad:e9:9e
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 38, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
orion_wdt: Initial timeout 171 sec
ledtrig-cpu: registered to indicate activity on CPUs
marvell-cesa f1090000.crypto: CESA device successfully registered
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
8021q: 802.1Q VLAN Support v1.8
Registering SWP/SWPB emulation handler
ata2: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
Loading compiled-in X.509 certificates
usb_phy_generic usb3_1-phy: Linked as a consumer to regulator.1
mv88e6085 f1072004.mdio-mii:00: switch 0x1760 detected: Marvell 88E6176, revision 1
libphy: mv88e6xxx SMI: probed
usb 1-1: new high-speed USB device number 2 using orion-ehci
mv88e6085 f1072004.mdio-mii:00 lan4 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540]
mv88e6085 f1072004.mdio-mii:00 lan3 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540]
mv88e6085 f1072004.mdio-mii:00 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540]
mv88e6085 f1072004.mdio-mii:00 lan1 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540]
mv88e6085 f1072004.mdio-mii:00 wan (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540]
DSA: tree 0 setup
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f8000.usb3: irq 43, io mem 0xf10f8000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usb-storage 1-1:1.0: USB Mass Storage device detected
input: gpio-keys as /devices/platform/gpio-keys/input/input0
hctosys: unable to open rtc device (rtc0)
cfg80211: Loading compiled-in X.509 certificates for regulatory database
scsi host2: usb-storage 1-1:1.0
cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
cfg80211: failed to load regulatory.db
Freeing unused kernel memory: 1024K
Run /init as init process
Loading, please wait...
starting version 232
random: systemd-udevd: uninitialized urandom read (16 bytes read)
random: udevadm: uninitialized urandom read (16 bytes read)
random: systemd-udevd: uninitialized urandom read (16 bytes read)
Begin: Loading essential drivers ... done.
scsi 2:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 6
sd 2:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] No Caching mode page found
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI removable disk
random: fast init done
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.29.2
[/sbin/fsck.f2fs (1) -- /dev/sda2] fsck.f2fs -a /dev/sda2
random: crng init done
random: 7 urandom warning(s) missed due to ratelimiting
Info: Fix the reported corruption.
Info: Segments per section = 1
Info: Sections per zone = 1
Info: sector size = 512
Info: total sectors = 7305216 (3567 MB)
Info: MKFS version
"Linux version 4.16.8+ (leigh@dish) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #14 SMP Thu May 10 1F2FS-fs (sda2): recover fsync data on readonly fs
4:52:50 BST 2018F2FS-fs (sda2): Mounted with checkpoint version = 1eb7
"
Info: FSCK version
from "Linux version 5.0.0-rc6 (leigh@dish) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #2 SMP Tue Feb 12 14:28:18 GMT 2019"
to "Linux version 5.0.0-rc6 (leigh@dish) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #2 SMP Tue Feb 12 15:04:14 GMT 2019"
Info: superblock features = 0 :
Info: superblock encrypt level = 0, salt = 00000000000000000000000000000000
Info: total FS sectors = 7305216 (3567 MB)
Info: CKPT version = 1eb7
Info: checkpoint state = 45 : compacted_summary unmount
[FSCK] Unreachable nat entries [Ok..] [0x0]
[FSCK] SIT valid block bitmap checking [Ok..]
[FSCK] Hard link checking for regular file [Ok..] [0x3]
[FSCK] valid_block_count matching with CP [Ok..] [0x305cb]
[FSCK] valid_node_count matcing with CP (de lookup) [Ok..] [0x6f28]
[FSCK] valid_node_count matcing with CP (nat lookup) [Ok..] [0x6f28]
[FSCK] valid_inode_count matched with CP [Ok..] [0x6eeb]
[FSCK] free segment_count matched with CP [Ok..] [0x559]
[FSCK] next block offset is free [Ok..]
[FSCK] fixing SIT types
[FSCK] other corrupted bugs [Ok..]
Done.
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...sd 2:0:0:0: Attached scsi generic sg0 type 0
<<Marvell Mac80211 Wireless PCIE Network Driver version 10.3.8.0-20181210>>
pci 0000:00:01.0: enabling device (0140 -> 0142)
ieee80211 phy0: device node: pcie@1,0
ieee80211 phy0: firmware version: 0x702091a
ieee80211 phy0: firmware region code: 30
ieee80211 phy0: 2G enabled, 5G enabled
ieee80211 phy0: 4 TX antennas, 4 RX antennas
pci 0000:00:02.0: enabling device (0140 -> 0142)
ieee80211 phy1: device node: pcie@2,0
ieee80211 phy1: firmware version: 0x702091a
ieee80211 phy1: firmware region code: 30
ieee80211 phy1: 2G enabled, 5G enabled
ieee80211 phy1: 4 TX antennas, 4 RX antennas
mwlwifi 0000:02:00.0 wlp2s0: renamed from wlan1
mwlwifi 0000:01:00.0 wlp1s0: renamed from wlan0
done.
[ ok ] Activating swap...done.
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.29.2
done.
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables...done.
mvneta f1070000.ethernet eth0: configuring for fixed/rgmii-id link mode
mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
mvneta f1034000.ethernet eth1: configuring for fixed/sgmii link mode
mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
lan: port 1(lan1) entered blocking state
lan: port 1(lan1) entered disabled state
device lan1 entered promiscuous mode
device eth1 entered promiscuous mode
mv88e6085 f1072004.mdio-mii:00 lan1: configuring for phy/gmii link mode
lan: port 2(lan2) entered blocking state
lan: port 2(lan2) entered disabled state
device lan2 entered promiscuous mode
mv88e6085 f1072004.mdio-mii:00 lan2: configuring for phy/gmii link mode
lan: port 3(lan3) entered blocking state
lan: port 3(lan3) entered disabled state
device lan3 entered promiscuous mode
mv88e6085 f1072004.mdio-mii:00 lan3: configuring for phy/gmii link mode
lan: port 4(lan4) entered blocking state
lan: port 4(lan4) entered disabled state
device lan4 entered promiscuous mode
mv88e6085 f1072004.mdio-mii:00 lan4: configuring for phy/gmii link mode
[....] Configuring network interfaces...
Waiting for lan to get ready (MAXWAIT is 32 seconds).
Waiting for DAD... mv88e6085 f1072004.mdio-mii:00 lan1: Link is Up - 1Gbps/Full - flow control off
lan: port 1(lan1) entered blocking state
lan: port 1(lan1) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready
Done
Waiting for DAD... Done
Waiting for DAD... Done
Waiting for DAD... Done
Waiting for DAD... Done
done.
[ ok ] Cleaning up temporary files....
#### WARNING ####
The firewall won't be started/stopped unless it is configured
Please read about Debian specific customization in
/usr/share/doc/shorewall6/README.Debian.gz.
#################
#### WARNING ####
The firewall won't be started/stopped unless it is configured
Please read about Debian specific customization in
/usr/share/doc/shorewall/README.Debian.gz.
#################
[39;4INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2422 (syslogd)
. ok
Starting radvd:
* /etc/radvd.conf does not exist or is empty.
* See /usr/share/doc/radvd/README.Debian
* radvd will *not* be started.
Starting Dropbear SSH server: dropbear.
Starting /usr/sbin/chronyd...
[ ok ] Starting periodic command scheduler: cron.
Requesting: lan as upstream: Y downstream: Y
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2429 (klogd)
. ok
Debian GNU/Linux 9 wrt1900acs ttyS0
wrt1900acs login:
