If the firmware or kernel has arranged memory for PCIe devices in a way that
doesn't provide enough space for BARs of a new hotplugged device, the kernel
can pause the drivers of the "obstructing" devices and move their BARs, so
new BARs can fit into the freed spaces.
When a driver is un-paused by the kernel after the PCIe rescan, it should
check if its BARs had moved, and ioremap() them if needed.
Drivers indicate their support of the feature by implementing the new
rescan_prepare() and rescan_done() hooks in the struct pci_driver. If a
driver doesn't yet support the feature, BARs of its devices will be marked
as immovable by the IORESOURCE_PCI_FIXED flag.
To re-arrange the BARs and bridge windows this patch releases all of them
after a rescan and re-assigns in the same way as during the initial PCIe
topology scan at system boot.
Tested on:
- x86_64 with "pci=realloc,assign-busses,use_crs"
- ppc64le POWER8 PowerNV (with extra arch-specific patches which will be
introduced later) with "pci=realloc pcie_movable_bars=force"
Not so many platforms and test cases were covered, so all who are interested
are highly welcome to test on your setups - the more exotic the better!
Changes since v1:
- Add a "pcie_movable_bars={ off | force }" command line argument;
- Handle the IORESOURCE_PCI_FIXED flag properly;
- Don't move BARs of devices which don't support the feature;
- Guarantee that new hotplugged devices will not steal memory from working
devices by ignoring the failing new devices with the new PCI_DEV_IGNORE
flag;
- Add rescan_prepare()+rescan_done() to the struct pci_driver instead of
using the reset_prepare()+reset_done() from struct pci_error_handlers;
- Add a bugfix of a race condition;
- Fixed hotplug in a non-pre-enabled (by BIOS/firmware) bridge;
- Fix the compatibility of the feature with pm_runtime and D3-state;
- Hotplug events from pciehp also can move BARs;
- Add support of the feature to the NVME driver.
This patchset is a part of our work on adding support for hotplugging
bridges full of NVME and GPU devices (without special requirement such as
Hot-Plug Controller, reservation of bus numbers and memory regions by
firmware, etc.). Next patchset will implement the movable bus numbers.
Sergey Miroshnichenko (21):
PCI: Fix writing invalid BARs during pci_restore_state()
PCI: Define PCI-specific version of the release_child_resources()
PCI: hotplug: Add a flag for the movable BARs feature
PCI: Pause the devices with movable BARs during rescan
PCI: Release and reassign the root bridge resources during rescan
PCI: Don't allow hotplugged devices to steal resources
PCI: Mark immovable BARs with PCI_FIXED
PCI: Include fixed BARs into the bus size calculating
PCI: Don't reserve memory for hotplug when enabled movable BARs
PCI: Allow the failed resources to be reassigned later
PCI: Calculate fixed areas of bridge windows based on fixed BARs
PCI: Calculate boundaries for bridge windows
PCI: Make sure bridge windows include their fixed BARs
PCI: Prioritize fixed BAR assigning over the movable ones
PCI: Fix race condition in pci_enable/disable_device()
PCI: Enable bridge's I/O and MEM access for hotplugged devices
PCI: pciehp: Add support for the movable BARs feature
nvme-pci: Handle movable BARs
powerpc/pci: Fix crash with enabled movable BARs
PCI: Wake up bridges during rescan when movable BARs enabled
x86: enable movable BARs
.../admin-guide/kernel-parameters.txt | 7 +
arch/powerpc/platforms/powernv/pci-ioda.c | 3 +-
arch/x86/pci/init.c | 2 +
drivers/nvme/host/pci.c | 29 +-
drivers/pci/bus.c | 7 +-
drivers/pci/hotplug/pciehp_pci.c | 14 +-
drivers/pci/pci.c | 60 +++-
drivers/pci/pci.h | 26 ++
drivers/pci/probe.c | 271 +++++++++++++++++-
drivers/pci/setup-bus.c | 229 +++++++++++++--
drivers/pci/setup-res.c | 45 ++-
include/linux/pci.h | 14 +
12 files changed, 670 insertions(+), 37 deletions(-)
--
2.20.1
