Hi Jim,
On Wed, Sep 19, 2018 at 10:32:01AM -0400, Jim Quinlan wrote:
> The design of the Broadcom PCIe RC controller requires us to remap its
> DMA addresses for inbound traffic. We do this by modifying the
> definitions of __phys_to_dma() and __dma_to_phys().
>
> In arch/mips/bmips/dma.c, these functions are already in use to remap
> DMA addresses for the 338x SOC chips. We leave this code alone -- and
> give its mapping priority -- but if it is not in use, the PCIe DMA
> mapping is in effect.
>
> One might think that the two DMA remapping systems of dma.c could be
> combined, but they cannot: one governs only DMA addresses for the PCIe
> controller of BrcmSTB ARM/ARM64/MIPs chips, while the other governs
> the PCIe controller *and* other peripherals for only MIPs 338x
> chips.
>
> Signed-off-by: Jim Quinlan <jim2101024@xxxxxxxxx>
> ---
> arch/mips/bmips/dma.c | 9 +++++++++
> 1 file changed, 9 insertions(+)
Please copy me/linux-mips on the whole series next time - I seem to have
only received patches 6, 8 & 9 which means I have no idea whether they
have dependencies & if so whether those dependencies have been accepted
or rejected. I also have no clue whether these patches make sense to
take through the MIPS tree or if it would make more sense for someone
else to take them with acks.
> diff --git a/arch/mips/bmips/dma.c b/arch/mips/bmips/dma.c
> index 3d13c77..292994f 100644
> --- a/arch/mips/bmips/dma.c
> +++ b/arch/mips/bmips/dma.c
> @@ -18,6 +18,7 @@
> #include <linux/slab.h>
> #include <linux/types.h>
> #include <asm/bmips.h>
> +#include <soc/brcmstb/common.h>
>
> /*
> * BCM338x has configurable address translation windows which allow the
> @@ -44,6 +45,10 @@ dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t pa)
> {
> struct bmips_dma_range *r;
>
> +#ifdef CONFIG_PCIE_BRCMSTB
> + if (!bmips_dma_ranges)
> + return brcm_phys_to_dma(dev, pa);
> +#endif
> for (r = bmips_dma_ranges; r && r->size; r++) {
> if (pa >= r->child_addr &&
> pa < (r->child_addr + r->size))
I can't tell because I presume brcm_phys_to_dma() is added in one of
those patches I wasn't copied on, but perhaps you could avoid the #ifdef
by just returning brcm_phys_to_dma(dev, pa) after the loop?
> @@ -56,6 +61,10 @@ phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t dma_addr)
> {
> struct bmips_dma_range *r;
>
> +#ifdef CONFIG_PCIE_BRCMSTB
> + if (!bmips_dma_ranges)
> + return (unsigned long)brcm_dma_to_phys(dev, dma_addr);
> +#endif
> for (r = bmips_dma_ranges; r && r->size; r++) {
> if (dma_addr >= r->parent_addr &&
> dma_addr < (r->parent_addr + r->size))
And similar here.
Thanks,
Paul
