Add DT bindings for PCIe controller implemented in UniPhier SoCs when
configured in Root Complex (host) mode. This controller is based on
the Designware PCIe Core.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@xxxxxxxxxxxxx>
---
.../devicetree/bindings/pci/uniphier-pcie.txt | 78 ++++++++++++++++++++++
1 file changed, 78 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/uniphier-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
new file mode 100644
index 0000000..ea63f78
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
@@ -0,0 +1,78 @@
+Socionext UniPhier PCI-express host controller bindings
+
+This describes the devicetree bindings for PCI-express host controller
+implemented on Socionext UniPhier SoCs.
+
+UniPhier PCI-express host controller is based on the Synopsys DesignWare
+PCI core. It shares common functions with the PCIe DesignWare core driver
+and inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
+
+Required properties:
+- compatible: Should be "socionext,uniphier-pcie".
+- reg: Specifies offset and length of the register set for the device.
+ According to the reg-names, appropriate register sets are required.
+- reg-names: Must include the following entries:
+ "dbi" - controller configuration registers
+ "link" - SoC-specific glue layer registers
+ "config" - PCIe configuration space
+- clocks: A phandle to the clock gate for PCIe glue layer including
+ the host controller.
+- resets: A phandle to the reset line for PCIe glue layer including
+ the host controller.
+- interrupts: A list of interrupt specifiers. According to the
+ interrupt-names, appropriate interrupts are required.
+- interrupt-names: Must include the following entries:
+ "dma" - DMA interrupt
+ "msi" - MSI interrupt
+ "intx" - Legacy INTA/B/C/D interrupt
+
+Optional properties:
+- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate
+ phys are required.
+- phy-names: Must be "pcie-phy".
+
+Required sub-node:
+- interrupt-controller: Specifies interrupt controller for legacy PCI
+ interrupts. The node name isn't important.
+
+Required properties for interrupt-controller:
+- interrupt-controller: identifies the node as an interrupt controller.
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+
+Example:
+
+ pcie: pcie@66000000 {
+ compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
+ status = "disabled";
+ reg-names = "dbi", "link", "config";
+ reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
+ <0x2fff0000 0x10000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&sys_clk 24>;
+ resets = <&sys_rst 24>;
+ num-lanes = <1>;
+ num-viewport = <1>;
+ bus-range = <0x0 0xff>;
+ device_type = "pci";
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000
+ /* non-prefetchable memory */
+ 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>;
+ #interrupt-cells = <1>;
+ interrupt-names = "dma", "msi", "intx";
+ interrupts = <0 224 4>, <0 225 4>, <0 226 4>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */
+ <0 0 0 2 &pcie_intc 1>, /* INTB */
+ <0 0 0 3 &pcie_intc 2>, /* INTC */
+ <0 0 0 4 &pcie_intc 3>; /* INTD */
+
+ pcie_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
--
2.7.4
