On Tue, 7 Aug 2018, Marcin Wojtas wrote:
> Ard, Mikulas,
>
> After some self-caused setup issues I was able to run the test on my
> MacchiatoBin with the kernel v4.18-rc8. It's been running for 1h+ now,
> loading the CPU to 100% and no single error event...
>
> I built the binary file with:
> gcc-linaro-7.2.1-2017.11-x86_64_aarch64-linux-gnu/bin/aarch64-linux-gnu-gcc -O2
>
> Maybe it's the older firmware issue?
I have downloaded and built the firmware recently (it has timestamp Jul 30
2018).
Do you still have your firmware file "flash-image.bin" that you used, so
that I could try it?
> Please send the full bootlog with
> the very first line after reset. My board rev is v1.3 and I use
> mainline UEFI (newest edk2 + edk2-platforms) + newest publicly
> available ARM-TF and earliest firmware for this board.
>
> Best regards,
> Marcin
This is my bootlog:
BootROM - 2.03
Starting CP-0 IOROM 1.07
Booting from SD 0 (0x29)
Found valid image at boot postion 0x002
lNOTICE: Starting binary extension
NOTICE: SVC: SW Revision 0x0. SVC is not supported
mv_ddr: mv_ddr-devel-18.05.0-g84dd1d9 (Jul 30 2018 - 04:58:51 PM)
mv_ddr: completed successfully
NOTICE: Cold boot
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.4(release):armada-18.05.2:80bbf686
NOTICE: BL1: Built : 17:00:18, Jul 30 2018
NOTICE: BL1: Booting BL2
lNOTICE: BL2: v1.4(release):armada-18.05.2:80bbf686
NOTICE: BL2: Built : 17:00:21, Jul 30 2018
BL2: Initiating SCP_BL2 transfer to SCP
NOTICE: SCP_BL2 contains 2 concatenated images
NOTICE: Load image to CP1 MSS AP0
NOTICE: Loading MSS image from address 0x4023020 Size 0x135c to MSS at 0xf4280000
NOTICE: Done
NOTICE: Load image to AP0 MSS
NOTICE: Loading MSS image from address 0x402437c Size 0x1f6c to MSS at 0xf0580000
N
FreeRTOS 7.3.0 - Marvell cm3 - A8K release armada-18.05.1
OTICE: Done
NOTICE: SCP Image doesn't contain PM firmware
NOTICE: BL1: Booting BL31
lNOTICE: MSS PM is not supported in this build
NOTICE: BL31: v1.4(release):armada-18.05.2:80bbf686
NOTICE: BL31: Built : 17:00:21, Jul 30 2018
lUEFI firmware (version MARVELL_EFI built at 16:50:27 on Jul 30 2018)
Armada 8040 MachiatoBin Platform Init
Comphy0-0: PCIE0 5 Gbps
Comphy0-1: PCIE0 5 Gbps
Comphy0-2: PCIE0 5 Gbps
Comphy0-3: PCIE0 5 Gbps
Comphy0-4: SFI 10.31 Gbps
Comphy0-5: SATA1 5 Gbps
Comphy1-0: SGMII1 1.25 Gbps
Comphy1-1: SATA2 5 Gbps
Comphy1-2: USB3_HOST0 5 Gbps
Comphy1-3: SATA3 5 Gbps
Comphy1-4: SFI 10.31 Gbps
Comphy1-5: SGMII2 3.125 Gbps
UTMI PHY 0 initialized to USB Host0
UTMI PHY 1 initialized to USB Host1
UTMI PHY 2 initialized to USB Host0
Succesfully installed protocol interfaces
Error: Image at 000BF6F8000 start failed: 00000001
remove-symbol-file /usr/src/git/macchiato/edk2/Build/Armada80x0McBin-AARCH64/RELEASE_GCC5/AARCH64/MdeModulePkg/Universal/Acpi/AcpiPlatformDxe/AcpiPlatformDxe/DEBUG/AcpiPlatform.dll 0xBF6F9000
Detected w25q32bv SPI flash with page size 256 B, erase size 4 KB, total 4 MB
ramdisk:blckio install. Status=Success
Connect: PcieRoot(0x0)/Pci(0x0,0x0): Not Found
3h3h3hTianocore/EDK2 firmware version MARVELL_EFI
Press ESCAPE for boot options ...error: no suitable video mode found.
error: no video mode activated.
GNU GRUB version 2.02~beta3-5
/----------------------------------------------------------------------------\||||||||||||||||||||||||||\----------------------------------------------------------------------------/ Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, `e' to edit the commands
before booting or `c' for a command-line.
*Debian GNU/Linux Advanced options for Debian GNU/Linux System setup
The highlighted entry will be executed automatically in 5s. The highlighted entry will be executed automatically in 4s. Loading Linux 4.17.11 ...
EFI stub: Booting Linux Kernel...
EFI stub: Using DTB from configuration table
EFI stub: Exiting boot services and installing virtual address map...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd081]
[ 0.000000] Linux version 4.17.11 (root@leontynka) (gcc version 8.2.0 (Debian 8.2.0-2)) #10 SMP PREEMPT Fri Aug 3 18:29:35 CEST 2018
[ 0.000000] Machine model: Marvell 8040 MACCHIATOBin
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: EFI v2.70 by EDK II
[ 0.000000] efi: SMBIOS 3.0=0xbfed0000 ACPI 2.0=0xb6760000 MEMATTR=0xb8c63518 RNG=0xbffdcf98
[ 0.000000] efi: seeding entropy pool
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 26 pages/cpu @ (ptrval) s67096 r8192 d31208 u106496
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031688
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.17.11 root=/dev/mmcblk0p1 ro console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] software IO TLB [mem 0xbb810000-0xbf810000] (64MB) mapped at [ (ptrval)- (ptrval)]
[ 0.000000] Memory: 4033692K/4192256K available (4860K kernel code, 376K rwdata, 2452K rodata, 384K init, 2178K bss, 158564K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f022f000
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:160, num:32)
[ 0.000000] GICv2m: range[mem 0xf0280000-0xf0280fff], SPI[160:191]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:192, num:32)
[ 0.000000] GICv2m: range[mem 0xf0290000-0xf0290fff], SPI[192:223]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:224, num:32)
[ 0.000000] GICv2m: range[mem 0xf02a0000-0xf02a0fff], SPI[224:255]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:256, num:32)
[ 0.000000] GICv2m: range[mem 0xf02b0000-0xf02b0fff], SPI[256:287]
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[ 0.000113] Console: colour dummy device 174x49
[ 0.000124] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.08 BogoMIPS (lpj=83333)
[ 0.000129] pid_max: default: 32768 minimum: 301
[ 0.000151] Security Framework initialized
[ 0.000154] Yama: becoming mindful.
[ 0.000183] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.000199] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.016676] ASID allocator initialised with 65536 entries
[ 0.020006] Hierarchical SRCU implementation.
[ 0.023435] Remapping and enabling EFI services.
[ 0.026680] smp: Bringing up secondary CPUs ...
[ 0.043500] Detected PIPT I-cache on CPU1
[ 0.043522] CPU1: Booted secondary processor 0x0000000001 [0x410fd081]
[ 0.060176] Detected PIPT I-cache on CPU2
[ 0.060195] CPU2: Booted secondary processor 0x0000000100 [0x410fd081]
[ 0.076859] Detected PIPT I-cache on CPU3
[ 0.076872] CPU3: Booted secondary processor 0x0000000101 [0x410fd081]
[ 0.076901] smp: Brought up 1 node, 4 CPUs
[ 0.076910] SMP: Total of 4 processors activated.
[ 0.076913] CPU features: detected: 32-bit EL0 Support
[ 0.077194] CPU: All CPU(s) started at EL2
[ 0.077205] alternatives: patching kernel code
[ 0.077230] random: get_random_u64 called from compute_layout+0x94/0xe8 with crng_init=0
[ 0.077599] devtmpfs: initialized
[ 0.078967] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.078975] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 0.079032] pinctrl core: initialized pinctrl subsystem
[ 0.079183] SMBIOS 3.0.0 present.
[ 0.079191] DMI: Marvell Armada 8040 MacchiatoBin/Armada 8040 MacchiatoBin, BIOS EDK II Jul 30 2018
[ 0.079264] NET: Registered protocol family 16
[ 0.079484] cpuidle: using governor ladder
[ 0.079535] cpuidle: using governor menu
[ 0.079559] vdso: 2 pages (1 code @ (ptrval), 1 data @ (ptrval))
[ 0.079562] vdso: 2 pages (1 code @ (ptrval), 1 data @ (ptrval))
[ 0.079569] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.079681] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.082434] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.082669] ACPI: Interpreter disabled.
[ 0.082822] reg-fixed-voltage regulator-usb3-vbus0: could not find pctldev for node /cp0/config-space@f2000000/system-controller@440000/pinctrl/xhci0-vbus-pins, deferring probe
[ 0.082929] SCSI subsystem initialized
[ 0.083033] Registered efivars operations
[ 0.083398] clocksource: Switched to clocksource arch_sys_counter
[ 0.083517] pnp: PnP ACPI: disabled
[ 0.085008] NET: Registered protocol family 2
[ 0.085146] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.085156] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.085213] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.085441] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.085492] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.085507] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.085713] hw perfevents: unable to count PMU IRQs
[ 0.085718] hw perfevents: /ap806/config-space@f0000000/pmu: failed to register PMU devices!
[ 0.085823] kvm [1]: 8-bit VMID
[ 0.086279] kvm [1]: vgic interrupt IRQ1
[ 0.086339] kvm [1]: Hyp mode initialized successfully
[ 0.086649] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[ 0.088566] io scheduler noop registered
[ 0.088625] io scheduler cfq registered (default)
[ 0.089467] armada-ap806-pinctrl f06f4000.system-controller:pinctrl: registered pinctrl driver
[ 0.089690] armada-cp110-pinctrl f2440000.system-controller:pinctrl: registered pinctrl driver
[ 0.089843] armada-cp110-pinctrl f4440000.system-controller:pinctrl: registered pinctrl driver
[ 0.091439] mv_xor_v2 f0400000.xor: Marvell Version 2 XOR driver
[ 0.091583] mv_xor_v2 f0420000.xor: Marvell Version 2 XOR driver
[ 0.091736] mv_xor_v2 f0440000.xor: Marvell Version 2 XOR driver
[ 0.091897] mv_xor_v2 f0460000.xor: Marvell Version 2 XOR driver
[ 0.092084] mv_xor_v2 f26a0000.xor: Marvell Version 2 XOR driver
[ 0.092247] mv_xor_v2 f26c0000.xor: Marvell Version 2 XOR driver
[ 0.092432] mv_xor_v2 f46a0000.xor: Marvell Version 2 XOR driver
[ 0.092596] mv_xor_v2 f46c0000.xor: Marvell Version 2 XOR driver
[ 0.092685] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.092996] console [ttyS0] disabled
[ 0.113364] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 7, base_baud = 12500000) is a 16550A
[ 0.777029] console [ttyS0] enabled
[ 0.801032] f2702100.serial: ttyS1 at MMIO 0xf2702100 (irq = 26, base_baud = 15625000) is a 16550A
[ 0.830524] f4702000.serial: ttyS2 at MMIO 0xf4702000 (irq = 27, base_baud = 15625000) is a 16550A
[ 0.839705] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.846129] libphy: Fixed MDIO Bus: probed
[ 0.850384] libphy: orion_mdio_bus: probed
[ 0.854879] libphy: orion_mdio_bus: probed
[ 0.862575] mousedev: PS/2 mouse device common for all mice
[ 0.868314] rtc-efi rtc-efi: rtc core: registered rtc-efi as rtc0
[ 0.874446] i2c /dev entries driver
[ 0.880187] sdhci: Secure Digital Host Controller Interface driver
[ 0.886399] sdhci: Copyright(c) Pierre Ossman
[ 0.890777] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.896640] mmc0: Switching to 3.3V signalling voltage failed
[ 0.927528] mmc0: SDHCI controller on f06e0000.sdhci [f06e0000.sdhci] using ADMA 64-bit
[ 0.966330] mmc1: SDHCI controller on f2780000.sdhci [f2780000.sdhci] using ADMA 64-bit
[ 0.976142] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 0.984470] PCI: OF: host bridge /cp0/pcie@f2600000 ranges:
[ 0.990120] PCI: OF: IO 0xeff00000..0xeff0ffff -> 0x00000000
[ 0.996083] PCI: OF: MEM 0xc0000000..0xdfffffff -> 0xc0000000
[ 1.002050] PCI: OF: MEM 0x800000000..0x8ffffffff -> 0x800000000
[ 1.008301] mmc0: new high speed MMC card at address 0001
[ 1.008337] armada8k-pcie f2600000.pcie: link up
[ 1.013884] mmcblk0: mmc0:0001 8GME4R 7.28 GiB
[ 1.018427] armada8k-pcie f2600000.pcie: PCI host bridge to bus 0000:00
[ 1.023036] mmcblk0boot0: mmc0:0001 8GME4R partition 1 4.00 MiB
[ 1.029619] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.035652] mmcblk0boot1: mmc0:0001 8GME4R partition 2 4.00 MiB
[ 1.041101] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.047085] mmcblk0rpmb: mmc0:0001 8GME4R partition 3 512 KiB, chardev (250:0)
[ 1.053256] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff]
[ 1.067452] pci_bus 0000:00: root bus resource [mem 0x800000000-0x8ffffffff]
[ 1.074559] mmcblk0: p1 p2 p3
[ 1.077642] pci 0000:00:00.0: disabling Extended Tags (this device can't handle them)
[ 1.097253] pci 0000:00:00.0: BAR 9: assigned [mem 0x800000000-0x80fffffff 64bit pref]
[ 1.105218] pci 0000:00:00.0: BAR 0: assigned [mem 0x810000000-0x8100fffff 64bit]
[ 1.112749] pci 0000:00:00.0: BAR 8: assigned [mem 0xc0000000-0xc00fffff]
[ 1.119578] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.125712] pci 0000:01:00.0: BAR 0: assigned [mem 0x800000000-0x80fffffff 64bit pref]
[ 1.133705] pci 0000:01:00.0: BAR 2: assigned [mem 0xc0000000-0xc001ffff 64bit]
[ 1.141088] pci 0000:01:00.0: BAR 6: assigned [mem 0xc0020000-0xc003ffff pref]
[ 1.148353] pci 0000:01:00.1: BAR 0: assigned [mem 0xc0040000-0xc0043fff 64bit]
[ 1.155738] pci 0000:01:00.0: BAR 4: assigned [io 0x1000-0x10ff]
[ 1.161879] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.167139] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff]
[ 1.173274] pci 0000:00:00.0: bridge window [mem 0xc0000000-0xc00fffff]
[ 1.180106] pci 0000:00:00.0: bridge window [mem 0x800000000-0x80fffffff 64bit pref]
[ 1.188210] mmc1: new high speed SDHC card at address 1234
[ 1.193873] mmcblk1: mmc1:1234 SA08G 7.41 GiB
[ 1.198461] pcieport 0000:00:00.0: AER enabled with IRQ 32
[ 1.204020] pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
[ 1.210396] rtc-efi rtc-efi: setting system clock to 2018-08-06 20:01:28 UTC (1533585688)
[ 1.211676] mmcblk1: p1 p2
[ 1.220717] v_5v0_usb3_hst_vbus: disabling
[ 1.231509] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 1.239654] VFS: Mounted root (ext4 filesystem) readonly on device 179:1.
[ 1.248061] devtmpfs: mounted
[ 1.251151] Freeing unused kernel memory: 384K
[ 1.325623] random: fast init done
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[ 1.488069] NET: Registered protocol family 1
ERROR: could not open /proc/stat: No such file or directory
[....] Starting the hotplug events dispatcher: systemd-udevdstarting version 239
[ ok .
[....] Synthesizing the initial hotplug events...[ ok done.
[ 1.786418] EFI Variables Facility v0.08 2004-May-17
[....] Waiting for /dev to be fully populated...[ 1.804433] mvpp2 f2000000.ethernet eth0: Using random mac address fe:a5:21:f0:f8:7d
[ 1.806861] usbcore: registered new interface driver usbfs
[ 1.817792] usbcore: registered new interface driver hub
[ 1.817835] mvpp2 f4000000.ethernet eth1: Using random mac address 86:5f:16:0c:f9:16
[ 1.823172] usbcore: registered new device driver usb
[ 1.837065] mvpp2 f4000000.ethernet eth2: Using random mac address 8e:6e:60:9f:57:60
[ 1.849493] ahci f2540000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.851030] mvpp2 f4000000.ethernet eth3: Using random mac address c6:5e:07:9a:54:82
[ 1.859250] ahci f2540000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.874656] scsi host0: ahci
[ 1.877789] scsi host1: ahci
[ 1.880777] ata1: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x100 irq 57
[ 1.888777] ata2: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x180 irq 57
[ 1.897008] ahci f4540000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.905629] ahci f4540000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.914173] scsi host2: ahci
[ 1.917252] scsi host3: ahci
[ 1.920225] ata3: SATA max UDMA/133 mmio [mem 0xf4540000-0xf456ffff] port 0x100 irq 58
[ 1.928198] ata4: SATA max UDMA/133 mmio [mem 0xf4540000-0xf456ffff] port 0x180 irq 58
[ 1.928608] xhci-hcd f2500000.usb3: xHCI Host Controller
[ 1.942154] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 1
[ 1.951232] xhci-hcd f2500000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.959840] xhci-hcd f2500000.usb3: irq 59, io mem 0xf2500000
[ 1.966174] hub 1-0:1.0: USB hub found
[ 1.970058] hub 1-0:1.0: 1 port detected
[ 1.974150] xhci-hcd f2500000.usb3: xHCI Host Controller
[ 1.979551] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 2
[ 1.979558] xhci-hcd f2500000.usb3: Host supports USB 3.0 SuperSpeed
[ 1.993840] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.000947] cryptd: max_cpu_qlen set to 1000
[ 2.002463] hub 2-0:1.0: USB hub found
[ 2.010089] hub 2-0:1.0: 1 port detected
[ 2.014291] xhci-hcd f2510000.usb3: xHCI Host Controller
[ 2.019647] xhci-hcd f2510000.usb3: new USB bus registered, assigned bus number 3
[ 2.027219] xhci-hcd f2510000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 2.035823] xhci-hcd f2510000.usb3: irq 60, io mem 0xf2510000
[ 2.042445] hub 3-0:1.0: USB hub found
[ 2.046236] hub 3-0:1.0: 1 port detected
[ 2.050278] xhci-hcd f2510000.usb3: xHCI Host Controller
[ 2.055768] xhci-hcd f2510000.usb3: new USB bus registered, assigned bus number 4
[ 2.063314] xhci-hcd f2510000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.069818] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.078176] hub 4-0:1.0: USB hub found
[ 2.081972] hub 4-0:1.0: 1 port detected
[ 2.086215] xhci-hcd f4500000.usb3: xHCI Host Controller
[ 2.091581] xhci-hcd f4500000.usb3: new USB bus registered, assigned bus number 5
[ 2.099158] xhci-hcd f4500000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 2.107751] xhci-hcd f4500000.usb3: irq 61, io mem 0xf4500000
[ 2.113788] hub 5-0:1.0: USB hub found
[ 2.117586] hub 5-0:1.0: 1 port detected
[ 2.121642] xhci-hcd f4500000.usb3: xHCI Host Controller
[ 2.126988] xhci-hcd f4500000.usb3: new USB bus registered, assigned bus number 6
[ 2.134514] xhci-hcd f4500000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.141009] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.149354] hub 6-0:1.0: USB hub found
[ 2.153156] hub 6-0:1.0: 1 port detected
[ 2.162109] [drm] radeon kernel modesetting enabled.
[ 2.167730] radeon 0000:01:00.0: enabling device (0000 -> 0003)
[ 2.174555] [drm] initializing kernel modesetting (CEDAR 0x1002:0x68F9 0x1787:0x3000 0x00).
[ 2.223834] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.250489] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.256599] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.303985] ATOM BIOS: CEDAR
[ 2.306958] [drm] GPU not posted. posting now...
[ 2.314564] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 2.323482] radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
[ 2.331229] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 2.336194] [drm] RAM width 64bits DDR
[ 2.343406] [TTM] Zone kernel: Available graphics memory: 2017038 kiB
[ 2.349967] [TTM] Initializing pool allocator
[ 2.354353] [TTM] Initializing DMA pool allocator
[ 2.359105] [drm] radeon: 1024M of VRAM memory ready
[ 2.364109] [drm] radeon: 1024M of GTT memory ready.
[ 2.369260] [drm] Loading CEDAR Microcode
[ 2.370083] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.380025] ata2.00: ATA-8: ST4000DM000-1F2168, CC52, max UDMA/133
[ 2.386240] ata2.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.393559] ata2.00: configured for UDMA/133
[ 2.397952] scsi 1:0:0:0: Direct-Access ATA ST4000DM000-1F21 CC52 PQ: 0 ANSI: 5
[ 2.418024] sd 1:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 2.420812] [drm] Internal thermal controller with fan control
[ 2.425823] sd 1:0:0:0: [sda] 4096-byte physical blocks
[ 2.436947] sd 1:0:0:0: [sda] Write Protect is off
[ 2.441160] [drm] radeon: dpm initialized
[ 2.445807] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.459901] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 2.460082] usb 5-1: new high-speed USB device number 2 using xhci-hcd
[ 2.466365] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 2.467195] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[ 2.511728] NET: Registered protocol family 10
[ 2.516748] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2.522778] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 2.528771] Segment Routing with IPv6
[ 2.548836] [drm] PCIE GART of 1024M enabled (table at 0x000000000014C000).
[ 2.556059] radeon 0000:01:00.0: WB enabled
[ 2.560272] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0x (ptrval)
[ 2.571109] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0x (ptrval)
[ 2.585425] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c418 and cpu addr 0x (ptrval)
[ 2.596259] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.602916] [drm] Driver supports precise vblank timestamp query.
[ 2.609046] radeon 0000:01:00.0: radeon: MSI limited to 32-bit
[ 2.615006] radeon 0000:01:00.0: radeon: using MSI.
[ 2.619944] [drm] radeon: irq initialized.
[ 2.635912] hub 5-1:1.0: USB hub found
[ 2.639847] hub 5-1:1.0: 4 ports detected
[ 2.644731] [drm] ring test on 0 succeeded in 0 usecs
[ 2.649815] [drm] ring test on 3 succeeded in 3 usecs
[ 2.797941] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.833616] [drm] ring test on 5 succeeded in 1 usecs
[ 2.838697] [drm] UVD initialized successfully.
[ 2.843495] [drm] ib test on ring 0 succeeded in 0 usecs
[ 2.848884] [drm] ib test on ring 3 succeeded in 0 usecs
[ 2.905618] hub 6-1:1.0: USB hub found
[ 2.909579] hub 6-1:1.0: 4 ports detected
[ 2.986738] usb 5-1.4: new high-speed USB device number 3 using xhci-hcd
[ 3.006863] [drm] ib test on ring 5 succeeded
[ 3.011876] [drm] Radeon Display Connectors
[ 3.016085] [drm] Connector 0:
[ 3.019154] [drm] DP-1
[ 3.021698] [drm] HPD2
[ 3.024244] [drm] DDC: 0x6460 0x6460 0x6464 0x6464 0x6468 0x6468 0x646c 0x646c
[ 3.031672] [drm] Encoders:
[ 3.034653] [drm] DFP1: INTERNAL_UNIPHY1
[ 3.038941] [drm] Connector 1:
[ 3.042008] [drm] DVI-I-1
[ 3.044814] [drm] HPD4
[ 3.047358] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[ 3.054786] [drm] Encoders:
[ 3.057767] [drm] DFP2: INTERNAL_UNIPHY
[ 3.061968] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 3.066605] [drm] Connector 2:
[ 3.069672] [drm] DVI-I-2
[ 3.072478] [drm] HPD1
[ 3.075023] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 3.082450] [drm] Encoders:
[ 3.085430] [drm] DFP3: INTERNAL_UNIPHY1
[ 3.089719] [drm] CRT2: INTERNAL_KLDSCP_DAC2
[ 3.095924] hub 5-1.4:1.0: USB hub found
[ 3.100002] hub 5-1.4:1.0: 4 ports detected
[ 3.110713] mvpp2 f2000000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.118686] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3.206262] [drm] fb mappable at 0x80034D000
[ 3.210554] [drm] vram apper at 0x800000000
[ 3.214756] [drm] size 8294400
[ 3.217823] [drm] fb depth is 24
[ 3.221064] [drm] pitch is 7680
[ 3.264754] Console: switching to colour frame buffer device 240x67
[ 3.278056] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 3.299311] [drm] Initialized radeon 2.50.0 20080528 for 0000:01:00.0 on minor 0
[ ok done.
[....] Setting up keyboard layout...[ 3.351975] usb 6-1.4: new SuperSpeed USB device number 3 using xhci-hcd
[ ok done.
[ 3.458706] hub 6-1.4:1.0: USB hub found
[ 3.462996] hub 6-1.4:1.0: 4 ports detected
[ 3.540089] usb 5-1.4.1: new full-speed USB device number 4 using xhci-hcd
[ 3.551721] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.32
/dev/mmcblk0p1: clean, 165507/475136 files, 4946295/7599104 blocks
[ ok done.
[ 3.603163] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=60
[ 3.723430] usb 5-1.4.1: new high-speed USB device number 5 using xhci-hcd
[....] Activating lvm and md swap...[ ok done.
[....] Checking file systems...fsck from util-linux 2.32
checking super block...
filesystem is clean, no checking needed.
[ ok done.
[ 3.892330] usbcore: registered new interface driver usbhid
[ 3.898466] usbhid: USB HID core driver
[....] Cleaning up temporary files... /tmp[ ok .
[ 3.971996] usbcore: registered new interface driver snd-usb-audio
[ 3.981106] input: ASUS Xonar U7 MKII as /devices/platform/cp1/cp1:config-space@f4000000/f4500000.usb3/usb5/5-1/5-1.4/5-1.4.1/5-1.4.1:1.4/0003:0B05:183C.0001/input/input0
[ 3.996748] usb 5-1.4.2: new low-speed USB device number 6 using xhci-hcd
[info] Loading kernel module nf_conntrack_ftp.
[info] Loading kernel module snd-usb-audio.
[info] Loading kernel module fbcon.
modprobe: FATAL: Module fbcon not found in directory /lib/modules/4.17.11
[info] Loading kernel module udl.
modprobe: FATAL: Module udl not found in directory /lib/modules/4.17.11
[ 4.050298] hid-generic 0003:0B05:183C.0001: input: USB HID v1.00 Device [ASUS Xonar U7 MKII] on usb-f4500000.usb3-1.4.1/input4
[ 4.143548] random: alsactl: uninitialized urandom read (4 bytes read)
[ 4.159127] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/cp1/cp1:config-space@f4000000/f4500000.usb3/usb5/5-1/5-1.4/5-1.4.2/5-1.4.2:1.0/0003:046D:C01E.0002/input/input1
[ 4.175703] hid-generic 0003:046D:C01E.0002: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-f4500000.usb3-1.4.2/input0
[ 4.252844] Adding 4194300k swap on /i/SWAP. Priority:-2 extents:1 across:4194300k
[ 4.270569] mvpp2 f4000000.ethernet eth2: Link is Up - 100Mbps/Full - flow control rx/tx
[ 4.278738] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 4.316754] usb 5-1.4.3: new low-speed USB device number 7 using xhci-hcd
[....] Mounting local filesystems...[ ok done.
[....] Activating swapfile swap...[ ok done.
[....] Cleaning up temporary files...[ ok .
[ 4.366696] random: dd: uninitialized urandom read (512 bytes read)
[....] Starting Setting kernel variables: sysctl[ ok .
[ 4.468860] PPP generic driver version 2.4.2
[ 4.474859] input: GASIA PS2toUSB Adapter as /devices/platform/cp1/cp1:config-space@f4000000/f4500000.usb3/usb5/5-1/5-1.4/5-1.4.3/5-1.4.3:1.0/0003:0E8F:0020.0003/input/input2
[ 4.477505] NET: Registered protocol family 17
[ 4.539749] NET: Registered protocol family 24
[ 4.550179] hid-generic 0003:0E8F:0020.0003: input: USB HID v1.10 Keyboard [GASIA PS2toUSB Adapter] on usb-f4500000.usb3-1.4.3/input0
[ 4.566423] input: GASIA PS2toUSB Adapter as /devices/platform/cp1/cp1:config-space@f4000000/f4500000.usb3/usb5/5-1/5-1.4/5-1.4.3/5-1.4.3:1.1/0003:0E8F:0020.0004/input/input3
[....] Configuring network interfaces...Plugin rp-pppoe.so loaded.
ifup: interface eth0 already configured
ifup: interface eth2 already configured
[ ok done.
[....] Cleaning up temporary files...[ ok .
[ 4.636900] hid-generic 0003:0E8F:0020.0004: input: USB HID v1.10 Mouse [GASIA PS2toUSB Adapter] on usb-f4500000.usb3-1.4.3/input1
[ 4.660387] random: alsactl: uninitialized urandom read (4 bytes read)
[....] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix[ ok .
[....] Setting sensors limits...[ ok done.
[....] Setting up ALSA...[ ok done.
[....] Loading netfilter rules...run-parts: executing /usr/share/netfilter-persistent/plugins.d/15-ip4tables start
run-parts: executing /usr/share/netfilter-persistent/plugins.d/25-ip6tables start
[ 4.743426] usb 5-1.4.4: new high-speed USB device number 8 using xhci-hcd
[ ok done.
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Enabling additional executable binary formats: binfmt-support[ ok .
[....] Setting up console font and keymap...[ ok done.
[ 4.878142] udlfb 5-1.4.4:1.0: vendor descriptor length: 34 data: 22 5f 01 00 20 05 00 01 03 00 04
[ 4.887190] udlfb 5-1.4.4:1.0: DL chip limited to 2360000 pixel modes
[....] Starting enhanced syslogd: rsyslogd[ ok .
[ 5.046171] usb 5-1.4.4: Unable to get valid EDID from device/display
[ 5.055288] usb 5-1.4.4: fb1 is DisplayLink USB device (800x600, 1880K framebuffer memory)
[ 5.063655] usbcore: registered new interface driver udlfb
[....] Starting system message bus: dbus[ ok .
[....] Loading cpufreq kernel modules...[ ok done (none).
[....] Starting mouse interface server: gpm[ ok .
[....] Starting NTP server: ntpd[ ok .
[ 5.167095] urandom_read: 3 callbacks suppressed
[ 5.167098] random: automount: uninitialized urandom read (4 bytes read)
[ 5.195518] random: isc-worker0000: uninitialized urandom read (10 bytes read)
[ 5.202800] random: isc-worker0000: uninitialized urandom read (40 bytes read)
[....] Starting automount...[ ok .
[....] Starting domain name service...: bind9[ ok .
[....] Starting virtual private network daemon:[ ok .
[....] CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor not available...[ ok done.
Starting very small Busybox based DHCP server: Starting /usr/sbin/udhcpd...
udhcpd.
Starting radvd: radvd.
[....] Starting periodic command scheduler: cron[ ok .
[....] Starting OpenBSD Secure Shell server: sshd[ ok .
[....] Starting WIDE DHCPv6 client: dhcp6c[ ok .
Debian GNU/Linux buster/sid leontynka ttyS0
leontynka login: [ 10.373259] random: crng init done
[ 10.376676] random: 1 urandom warning(s) missed due to ratelimiting
[ 23.931568] tun: Universal TUN/TAP device driver, 1.6
