Lorenzo,
my apologies; I will make sure not to send multiple copies of same
patch next time.
Thanks.
On Tue, May 8, 2018 at 9:48 PM, Lorenzo Pieralisi
<lorenzo.pieralisi@xxxxxxx> wrote:
> On Mon, May 07, 2018 at 04:52:14AM -0400, Subrahmanya Lingappa wrote:
>> This patch adds the DT bindings for Mobiveil PCIe Host Bridge
>> IP driver and updates the vendor prefixes file.
>>
>> Signed-off-by: Subrahmanya Lingappa <l.subrahmanya@xxxxxxxxxxxxxx>
>> Acked-by: Rob Herring <robh@xxxxxxxxxx>
>> Cc: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
>> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@xxxxxxx>
>> Cc: linux-pci@xxxxxxxxxxxxxxx
>> Cc: devicetree@xxxxxxxxxxxxxxx
>> ---
>> .../devicetree/bindings/pci/mobiveil-pcie.txt | 73 ++++++++++++++++++++++
>> .../devicetree/bindings/vendor-prefixes.txt | 1 +
>> MAINTAINERS | 7 +++
>> 3 files changed, 81 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pci/mobiveil-pcie.txt
>
> You sent this patch twice, which confused patchwork (which we use to
> apply patches), please send the series to yourself to test it is right
> before sending it to the list.
>
> Thanks,
> Lorenzo
>
>>
>> diff --git a/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt
>> new file mode 100644
>> index 0000000..65038aa
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt
>> @@ -0,0 +1,73 @@
>> +* Mobiveil AXI PCIe Root Port Bridge DT description
>> +
>> +Mobiveil's GPEX 4.0 is a PCIe Gen4 root port bridge IP. This configurable IP
>> +has up to 8 outbound and inbound windows for the address translation.
>> +
>> +Required properties:
>> +- #address-cells: Address representation for root ports, set to <3>
>> +- #size-cells: Size representation for root ports, set to <2>
>> +- #interrupt-cells: specifies the number of cells needed to encode an
>> + interrupt source. The value must be 1.
>> +- compatible: Should contain "mbvl,gpex40-pcie"
>> +- reg: Should contain PCIe registers location and length
>> + "config_axi_slave": PCIe controller registers
>> + "csr_axi_slave" : Bridge config registers
>> + "gpio_slave" : GPIO registers to control slot power
>> + "apb_csr" : MSI registers
>> +
>> +- device_type: must be "pci"
>> +- apio-wins : number of requested apio outbound windows
>> + default 2 outbound windows are configured -
>> + 1. Config window
>> + 2. Memory window
>> +- ppio-wins : number of requested ppio inbound windows
>> + default 1 inbound memory window is configured.
>> +- bus-range: PCI bus numbers covered
>> +- interrupt-controller: identifies the node as an interrupt controller
>> +- #interrupt-cells: specifies the number of cells needed to encode an
>> + interrupt source. The value must be 1.
>> +- interrupt-parent : phandle to the interrupt controller that
>> + it is attached to, it should be set to gic to point to
>> + ARM's Generic Interrupt Controller node in system DT.
>> +- interrupts: The interrupt line of the PCIe controller
>> + last cell of this field is set to 4 to
>> + denote it as IRQ_TYPE_LEVEL_HIGH type interrupt.
>> +- interrupt-map-mask,
>> + interrupt-map: standard PCI properties to define the mapping of the
>> + PCI interface to interrupt numbers.
>> +- ranges: ranges for the PCI memory regions (I/O space region is not
>> + supported by hardware)
>> + Please refer to the standard PCI bus binding document for a more
>> + detailed explanation
>> +
>> +
>> +Example:
>> +++++++++
>> + pcie0: pcie@a0000000 {
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + compatible = "mbvl,gpex40-pcie";
>> + reg = <0xa0000000 0x00001000>,
>> + <0xb0000000 0x00010000>,
>> + <0xff000000 0x00200000>,
>> + <0xb0010000 0x00001000>;
>> + reg-names = "config_axi_slave",
>> + "csr_axi_slave",
>> + "gpio_slave",
>> + "apb_csr";
>> + device_type = "pci";
>> + apio-wins = <2>;
>> + ppio-wins = <1>;
>> + bus-range = <0x00000000 0x000000ff>;
>> + interrupt-controller;
>> + interrupt-parent = <&gic>;
>> + #interrupt-cells = <1>;
>> + interrupts = < 0 89 4 >;
>> + interrupt-map-mask = <0 0 0 7>;
>> + interrupt-map = <0 0 0 0 &pci_express 0>,
>> + <0 0 0 1 &pci_express 1>,
>> + <0 0 0 2 &pci_express 2>,
>> + <0 0 0 3 &pci_express 3>;
>> + ranges = < 0x83000000 0 0x00000000 0xa8000000 0 0x8000000>;
>> +
>> + };
>> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> index 0994bdd..8263cc7 100644
>> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
>> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> @@ -197,6 +197,7 @@ lwn Liebherr-Werk Nenzing GmbH
>> macnica Macnica Americas
>> marvell Marvell Technology Group Ltd.
>> maxim Maxim Integrated Products
>> +mbvl Mobiveil Inc.
>> mcube mCube
>> meas Measurement Specialties
>> mediatek MediaTek Inc.
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 44512c3..b295080 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -9162,6 +9162,13 @@ Q: http://patchwork.linuxtv.org/project/linux-media/list/
>> S: Maintained
>> F: drivers/media/dvb-frontends/mn88473*
>>
>> +PCI DRIVER FOR MOBIVEIL PCIE IP
>> +M: Subrahmanya Lingappa <l.subrahmanya@xxxxxxxxxxxxxx>
>> +L: linux-pci@xxxxxxxxxxxxxxx
>> +S: Supported
>> +F: Documentation/devicetree/bindings/pci/mobiveil-pcie.txt
>> +F: drivers/pci/host/pcie-mobiveil.c
>> +
>> MODULE SUPPORT
>> M: Jessica Yu <jeyu@xxxxxxxxxx>
>> M: Rusty Russell <rusty@xxxxxxxxxxxxxxx>
>> --
>> 1.8.3.1
>>
