Re: 答复: 答复: [PATCH v6] mfd: Add support for RTS5250S power saving

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Dec 27, 2017 at 05:37:50PM -0600, Bjorn Helgaas wrote:
> On Tue, Dec 19, 2017 at 08:15:24AM +0000, 冯锐 wrote:
> > > On Fri, Dec 15, 2017 at 09:42:45AM +0000, 冯锐 wrote:
> > > > > [+cc Hans, Dave, linux-pci]
> > > > >
> > > > > On Thu, Sep 07, 2017 at 04:26:39PM +0800, rui_feng@xxxxxxxxxxxxxx
> > > wrote:
> > > > > > From: Rui Feng <rui_feng@xxxxxxxxxxxxxx>
> > > > >
> > > > > I wish this had been posted to linux-pci before being merged.
> > > > >
> > > > > I'm concerned because some of this appears to overlap and conflict
> > > > > with PCI core management of ASPM.
> > > > >
> > > > > I assume these devices advertise ASPM support in their Link
> > > > > Capabilites registers, right?  If so, why isn't the existing PCI
> > > > > core ASPM support sufficient?
> > > > >
> > > > When L1SS is configured, the device(hardware) can't enter L1SS status
> > > > automatically, it need driver(software) to do some work to achieve the
> > > function.
> > > 
> > > So this is a hardware defect in the device?  As far as I know, ASPM and L1SS
> > > are specified such that they should work without special driver support.
> > > 
> > Yes, you can say that.
> > 
> > > > > > Enable power saving for RTS5250S as following steps:
> > > > > > 1.Set 0xFE58 to enable clock power management.
> > > > >
> > > > > Is this clock power management something specific to RTS5250S, or is
> > > > > it standard PCIe architected stuff?
> > > > >
> > > > 0xFE58 is specific register to RTS5250S not standard PCIe architected stuff.
> > > 
> > > OK.  I asked because devices often mirror architected PCIe config things in
> > > device-specific MMIO space, and if I squint just right, I can sort of match up the
> > > register bits you used with things in the PCIe spec.
> > > 
> > > > > > 2.Check cfg space whether support L1SS or not.
> > > > >
> > > > > This sounds like standard PCIe ASPM L1 Substates, right?
> > > > >
> > > > Yes.
> > > >
> > > > > > 3.If support L1SS, set 0xFF03 to free clkreq.
> > > > > > 4.When entering idle status, enable aspm
> > > > > >   and set parameters for L1SS and LTR.
> > > > > > 5.Wnen entering run status, disable aspm
> > > > > >   and set parameters for L1SS and LTR.
> > > > >
> > > > > In general, drivers should not configure ASPM, L1SS, and LTR
> > > > > themselves; the PCI core should do that.
> > > > >
> > > > > If a driver needs to tweak ASPM at run-time, it should use
> > > > > interfaces exported by the PCI core to do so.
> > > > >
> > > > Which interface I can use to set ASPM? I use "pci_write_config_byte" now.
> > > 
> > > What do you need to do?  include/linux/pci-aspm.h exports
> > > pci_disable_link_state(), which is mainly used to avoid ASPM
> > > states that have hardware errata.
> > > 
> > I want to enable ASPM(L0 -> L1) and disable ASPM(L1 -> L0), which
> > interface can I use?
> 
> You can use pci_disable_link_state() to disable usage of L1.
> 
> Currently there is no corresponding pci_enable_link_state().  What if
> we added something like the following (untested)?  Would that work for
> you?

Hi Rui,

Any thoughts on the patch below?

> commit 209930d809fa602b8aafdd171b26719cee6c6649
> Author: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> Date:   Wed Dec 27 16:56:26 2017 -0600
> 
>     PCI/ASPM: Add pci_enable_link_state()
>     
>     Some drivers want control over the ASPM states their device is allowed to
>     use.  We already have a pci_disable_link_state(), and drivers can use that
>     to prevent the device from entering L0 or L1s.
>     
>     Add a corresponding pci_enable_link_state() so a driver can enable use of
>     L0 or L1s again.
> 
> diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c
> index 3b9b4d50cd98..ca217195f800 100644
> --- a/drivers/pci/pcie/aspm.c
> +++ b/drivers/pci/pcie/aspm.c
> @@ -1028,6 +1028,67 @@ void pcie_aspm_powersave_config_link(struct pci_dev *pdev)
>  	up_read(&pci_bus_sem);
>  }
>  
> +/**
> + * pci_enable_link_state - Enable device's link state, so the link may
> + * enter specific states.  Note that if the BIOS didn't grant ASPM
> + * control to the OS, this does nothing because we can't touch the LNKCTL
> + * register.
> + *
> + * @pdev: PCI device
> + * @state: ASPM link state to enable
> + */
> +void pci_enable_link_state(struct pci_dev *pdev, int state)
> +{
> +	struct pci_dev *parent = pdev->bus->self;
> +	struct pcie_link_state *link;
> +	u32 lnkcap;
> +
> +	if (!pci_is_pcie(pdev))
> +		return;
> +
> +	if (pdev->has_secondary_link)
> +		parent = pdev;
> +	if (!parent || !parent->link_state)
> +		return;
> +
> +	/*
> +	 * A driver requested that ASPM be enabled on this device, but
> +	 * if we don't have permission to manage ASPM (e.g., on ACPI
> +	 * systems we have to observe the FADT ACPI_FADT_NO_ASPM bit and
> +	 * the _OSC method), we can't honor that request.  Windows has
> +	 * a similar mechanism using "PciASPMOptOut", which is also
> +	 * ignored in this situation.
> +	 */
> +	if (aspm_disabled) {
> +		dev_warn(&pdev->dev, "can't enable ASPM; OS doesn't have ASPM control\n");
> +		return;
> +	}
> +
> +	down_read(&pci_bus_sem);
> +	mutex_lock(&aspm_lock);
> +	link = parent->link_state;
> +	if (state & PCIE_LINK_STATE_L0S)
> +		link->aspm_disable &= ~ASPM_STATE_L0S;
> +	if (state & PCIE_LINK_STATE_L1)
> +		link->aspm_disable &= ~ASPM_STATE_L1;
> +	pcie_config_aspm_link(link, policy_to_aspm_state(link));
> +
> +	/*
> +	 * Enable Clock Power Management if requested by the driver,
> +	 * supported by the device, and allowed by the current policy.
> +	 */
> +	if (state & PCIE_LINK_STATE_CLKPM) {
> +		pcie_capability_read_dword(pdev, PCI_EXP_LNKCAP, &lnkcap);
> +		if (lnkcap & PCI_EXP_LNKCAP_CLKPM) {
> +			link->clkpm_capable = 1;
> +			pcie_set_clkpm(link, policy_to_clkpm_state(link));
> +		}
> +	}
> +	mutex_unlock(&aspm_lock);
> +	up_read(&pci_bus_sem);
> +}
> +EXPORT_SYMBOL(pci_enable_link_state);
> +
>  static void __pci_disable_link_state(struct pci_dev *pdev, int state, bool sem)
>  {
>  	struct pci_dev *parent = pdev->bus->self;
> diff --git a/include/linux/pci-aspm.h b/include/linux/pci-aspm.h
> index df28af5cef21..cd0736b384ae 100644
> --- a/include/linux/pci-aspm.h
> +++ b/include/linux/pci-aspm.h
> @@ -24,10 +24,12 @@
>  #define PCIE_LINK_STATE_CLKPM	4
>  
>  #ifdef CONFIG_PCIEASPM
> +void pci_enable_link_state(struct pci_dev *pdev, int state);
>  void pci_disable_link_state(struct pci_dev *pdev, int state);
>  void pci_disable_link_state_locked(struct pci_dev *pdev, int state);
>  void pcie_no_aspm(void);
>  #else
> +static inline void pci_enable_link_state(struct pci_dev *pdev, int state) { }
>  static inline void pci_disable_link_state(struct pci_dev *pdev, int state) { }
>  static inline void pcie_no_aspm(void) { }
>  #endif



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux