On 11/10/2017 10:03 AM, Simon Horman wrote:
> On Wed, Nov 08, 2017 at 10:28:05AM +0100, Marek Vasut wrote:
>> From: Phil Edworthy <phil.edworthy@xxxxxxxxxxx>
>>
>> Most PCIe host controllers support L0s and L1 power states via ASPM.
>> The R-Car hardware only supports L0s, so when the system suspends and
>> resumes we have to manually handle L1.
>>
>> When the system suspends, cards can put themselves into L1 and send a
>> PM_ENTER_L1 DLLP to the host controller. At this point, we can no longer
>> access the card's config registers.
>>
>> The R-Car host controller will handle taking cards out of L1 as long as
>> the host controller has also been transitioned to L1 link state.
>>
>> Ideally, we would detect the PM_ENTER_L1 DLLP using an interrupt and
>> transition the host to L1 immediately. However, this patch just ensures
>> that we can talk to cards after they have gone into L1.
>> When attempting a config access, it checks to see if the card has gone
>> into L1, and if so, does the same for the host controller.
>>
>> This is based on a patch by Hien Dang <hien.dang.eb@xxxxxxxxxxxxxxx>
>>
>> Signed-off-by: Phil Edworthy <phil.edworthy@xxxxxxxxxxx>
>> Signed-off-by: Marek Vasut <marek.vasut+renesas@xxxxxxxxx>
>> Cc: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
>> Cc: Simon Horman <horms+renesas@xxxxxxxxxxxx>
>> Cc: Wolfram Sang <wsa@xxxxxxxxxxxxx>
>> Cc: linux-renesas-soc@xxxxxxxxxxxxxxx
>
> Hi Marek,
>
> With my nit addressed please feel free to add:
>
> Acked-by: Simon Horman <horms+renesas@xxxxxxxxxxxx>
>
>> ---
>> drivers/pci/host/pcie-rcar.c | 24 ++++++++++++++++++++++++
>> 1 file changed, 24 insertions(+)
>>
>> diff --git a/drivers/pci/host/pcie-rcar.c b/drivers/pci/host/pcie-rcar.c
>> index aa588a7d4811..2b28292de93a 100644
>> --- a/drivers/pci/host/pcie-rcar.c
>> +++ b/drivers/pci/host/pcie-rcar.c
>> @@ -92,6 +92,13 @@
>> #define MACCTLR 0x011058
>> #define SPEED_CHANGE (1 << 24)
>> #define SCRAMBLE_DISABLE (1 << 27)
>> +#define PMSR 0x01105c
>> +#define L1FAEG (1 << 31)
>> +#define PM_ENTER_L1RX (1 << 23)
>> +#define PMSTATE (7 << 16)
>> +#define PMSTATE_L1 (3 << 16)
>> +#define PMCTLR 0x011060
>> +#define L1_INIT (1 << 31)
>
> The BIT() and GENMASK() macros are nice in my opinion.
> But I see what you have added follows the style of the existing code
> in the driver.
I added a patch into the series to clean this up and will then use BIT()
and GENMASK() here too.
>> #define MACS2R 0x011078
>> #define MACCGSPSETR 0x011084
>> #define SPCNGRSN (1 << 31)
>> @@ -191,6 +198,7 @@ static int rcar_pcie_config_access(struct rcar_pcie *pcie,
>> unsigned int devfn, int where, u32 *data)
>> {
>> int dev, func, reg, index;
>> + u32 val;
>>
>> dev = PCI_SLOT(devfn);
>> func = PCI_FUNC(devfn);
>> @@ -232,6 +240,22 @@ static int rcar_pcie_config_access(struct rcar_pcie *pcie,
>> if (pcie->root_bus_nr < 0)
>> return PCIBIOS_DEVICE_NOT_FOUND;
>>
>> + /*
>> + * If we are not in L1 link state and we have received PM_ENTER_L1 DLLP,
>> + * transition to L1 link state. The HW will handle coming of of L1.
>> + */
>> + val = rcar_pci_read_reg(pcie, PMSR);
>> + if ((val & PM_ENTER_L1RX) && ((val & PMSTATE) != PMSTATE_L1)) {
>
> nit: please remove the unnecessary parentheses from the line above.
Fixed
>> + rcar_pci_write_reg(pcie, L1_INIT, PMCTLR);
>> +
>> + /* Wait until we are in L1 */
>> + while (!(val & L1FAEG))
>> + val = rcar_pci_read_reg(pcie, PMSR);
>> +
>> + /* Clear flags indicating link has transitioned to L1 */
>> + rcar_pci_write_reg(pcie, L1FAEG | PM_ENTER_L1RX, PMSR);
>> + }
>> +
>> /* Clear errors */
>> rcar_pci_write_reg(pcie, rcar_pci_read_reg(pcie, PCIEERRFR), PCIEERRFR);
>>
>> --
>> 2.11.0
>>
--
Best regards,
Marek Vasut
