Signed-off-by: Niklas Cassel <niklas.cassel@xxxxxxxx>
---
.../devicetree/bindings/pci/axis,artpec6-pcie.txt | 3 +-
drivers/pci/dwc/Kconfig | 41 +++--
drivers/pci/dwc/Makefile | 4 +-
drivers/pci/dwc/pcie-artpec6.c | 202 ++++++++++++++++++++-
4 files changed, 233 insertions(+), 17 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
index 4e4aee4439ea..33eef7ae5a23 100644
--- a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
@@ -4,7 +4,8 @@ This PCIe host controller is based on the Synopsys DesignWare PCIe IP
and thus inherits all the common properties defined in designware-pcie.txt.
Required properties:
-- compatible: "axis,artpec6-pcie", "snps,dw-pcie"
+- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode;
+ "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode;
- reg: base addresses and lengths of the PCIe controller (DBI),
the PHY controller, and configuration address space.
- reg-names: Must include the following entries:
diff --git a/drivers/pci/dwc/Kconfig b/drivers/pci/dwc/Kconfig
index 22ec82fcdea2..e333283fb1ed 100644
--- a/drivers/pci/dwc/Kconfig
+++ b/drivers/pci/dwc/Kconfig
@@ -14,6 +14,36 @@ config PCIE_DW_EP
depends on PCI_ENDPOINT
select PCIE_DW
+config PCIE_ARTPEC6
+ bool "Axis ARTPEC-6 PCIe controller"
+ depends on (PCI && PCI_MSI_IRQ_DOMAIN) || PCI_ENDPOINT
+ depends on MACH_ARTPEC6
+ help
+ Say Y here to enable PCIe controller support on Axis ARTPEC-6
+ SoCs. This PCIe controller uses the DesignWare core.
+
+if PCIE_ARTPEC6
+
+config PCIE_ARTPEC6_HOST
+ bool "Axis ARTPEC-6 Host Mode"
+ depends on PCI
+ depends on PCI_MSI_IRQ_DOMAIN
+ select PCIEPORTBUS
+ select PCIE_DW_HOST
+ help
+ Enables support for the PCIe controller in the ARTPEC-6 SoC to work in
+ host mode.
+
+config PCIE_ARTPEC6_EP
+ bool "Axis ARTPEC-6 Endpoint Mode"
+ depends on PCI_ENDPOINT
+ select PCIE_DW_EP
+ help
+ Enables support for the PCIe controller in the ARTPEC-6 SoC to work in
+ endpoint mode.
+
+endif
+
config PCI_DRA7XX
bool "TI DRA7xx PCIe controller"
depends on SOC_DRA7XX || COMPILE_TEST
@@ -148,17 +178,6 @@ config PCIE_ARMADA_8K
DesignWare hardware and therefore the driver re-uses the
DesignWare core functions to implement the driver.
-config PCIE_ARTPEC6
- bool "Axis ARTPEC-6 PCIe controller"
- depends on PCI
- depends on MACH_ARTPEC6
- depends on PCI_MSI_IRQ_DOMAIN
- select PCIEPORTBUS
- select PCIE_DW_HOST
- help
- Say Y here to enable PCIe controller support on Axis ARTPEC-6
- SoCs. This PCIe controller uses the DesignWare core.
-
config PCIE_KIRIN
depends on OF && ARM64
bool "HiSilicon Kirin series SoCs PCIe controllers"
diff --git a/drivers/pci/dwc/Makefile b/drivers/pci/dwc/Makefile
index c61be9738cce..ac98242b83a9 100644
--- a/drivers/pci/dwc/Makefile
+++ b/drivers/pci/dwc/Makefile
@@ -2,6 +2,9 @@ obj-$(CONFIG_PCIE_DW) += pcie-designware.o
obj-$(CONFIG_PCIE_DW_HOST) += pcie-designware-host.o
obj-$(CONFIG_PCIE_DW_EP) += pcie-designware-ep.o
obj-$(CONFIG_PCIE_DW_PLAT) += pcie-designware-plat.o
+ifneq ($(filter y,$(CONFIG_PCIE_ARTPEC6_HOST) $(CONFIG_PCIE_ARTPEC6_EP)),)
+ obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
+endif
ifneq ($(filter y,$(CONFIG_PCI_DRA7XX_HOST) $(CONFIG_PCI_DRA7XX_EP)),)
obj-$(CONFIG_PCI_DRA7XX) += pci-dra7xx.o
endif
@@ -12,7 +15,6 @@ obj-$(CONFIG_PCI_KEYSTONE) += pci-keystone-dw.o pci-keystone.o
obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o
obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
-obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
# The following drivers are for devices that use the generic ACPI
diff --git a/drivers/pci/dwc/pcie-artpec6.c b/drivers/pci/dwc/pcie-artpec6.c
index c5d7f98dc6b2..21ea9ffef784 100644
--- a/drivers/pci/dwc/pcie-artpec6.c
+++ b/drivers/pci/dwc/pcie-artpec6.c
@@ -13,6 +13,7 @@
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/of_device.h>
#include <linux/pci.h>
#include <linux/platform_device.h>
#include <linux/resource.h>
@@ -30,8 +31,15 @@ struct artpec6_pcie {
struct dw_pcie *pci;
struct regmap *regmap; /* DT axis,syscon-pcie */
void __iomem *phy_base; /* DT phy */
+ enum dw_pcie_device_mode mode;
};
+struct artpec_pcie_of_data {
+ enum dw_pcie_device_mode mode;
+};
+
+static const struct of_device_id artpec6_pcie_of_match[];
+
/* PCIe Port Logic registers (memory-mapped) */
#define PL_OFFSET 0x700
#define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28)
@@ -42,6 +50,7 @@ struct artpec6_pcie {
#define PCIECFG_DBG_OEN BIT(24)
#define PCIECFG_CORE_RESET_REQ BIT(21)
#define PCIECFG_LTSSM_ENABLE BIT(20)
+#define PCIECFG_DEVICE_TYPE_MASK GENMASK(19, 16)
#define PCIECFG_CLKREQ_B BIT(11)
#define PCIECFG_REFCLK_ENABLE BIT(10)
#define PCIECFG_PLL_ENABLE BIT(9)
@@ -126,6 +135,16 @@ static void artpec6_pcie_init_phy(struct artpec6_pcie *artpec6_pcie)
} while (retries && !(val & PHY_COSPLLLOCK));
}
+static void artpec6_pcie_stop_link(struct dw_pcie *pci)
+{
+ struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci);
+ u32 val;
+
+ val = artpec6_pcie_readl(artpec6_pcie, PCIECFG);
+ val &= ~PCIECFG_LTSSM_ENABLE;
+ artpec6_pcie_writel(artpec6_pcie, PCIECFG, val);
+}
+
static int artpec6_pcie_establish_link(struct dw_pcie *pci)
{
struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci);
@@ -195,6 +214,136 @@ static irqreturn_t artpec6_pcie_msi_handler(int irq, void *arg)
return dw_handle_msi_irq(pp);
}
+static void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
+{
+ u32 reg;
+
+ reg = PCI_BASE_ADDRESS_0 + (4 * bar);
+ dw_pcie_dbi_ro_wr_en(pci);
+ dw_pcie_writel_dbi2(pci, reg, 0x0);
+ dw_pcie_writel_dbi(pci, reg, 0x0);
+ dw_pcie_dbi_ro_wr_dis(pci);
+}
+
+static void artpec6_pcie_ep_init(struct dw_pcie_ep *ep)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+ struct artpec6_pcie *artpec6_pcie = to_artpec6_pcie(pci);
+ enum pci_barno bar;
+
+ artpec6_pcie_assert_core_reset(artpec6_pcie);
+ artpec6_pcie_init_phy(artpec6_pcie);
+ artpec6_pcie_deassert_core_reset(artpec6_pcie);
+
+ for (bar = BAR_0; bar <= BAR_5; bar++)
+ dw_pcie_ep_reset_bar(pci, bar);
+}
+
+static int artpec6_pcie_raise_msi_irq(struct dw_pcie_ep *ep,
+ u8 interrupt_num)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+ struct pci_epc *epc = ep->epc;
+ u32 cap_addr, cap_value, cap_id, next_ptr, msg_ctrl, msg_data;
+ u32 msg_addr_lower, msg_addr_upper;
+ u64 msg_addr;
+ bool has_upper;
+ int ret;
+
+ /* Raise MSI per the PCI Local Bus Specification Revision 3.0, 6.8.1. */
+ cap_addr = dw_pcie_readl_dbi(pci, PCI_CAPABILITY_LIST);
+ while (1) {
+ cap_value = dw_pcie_readl_dbi(pci, cap_addr);
+ cap_id = cap_value & GENMASK(7, 0);
+ if (cap_id == PCI_CAP_ID_MSI)
+ break;
+ next_ptr = (cap_value & GENMASK(15, 8)) >> 8;
+ if (next_ptr == 0) {
+ dev_err(pci->dev, "No MSI cap found!\n");
+ return -EINVAL;
+ }
+ cap_addr = next_ptr;
+ }
+ msg_ctrl = (cap_value & GENMASK(31, 16)) >> 16;
+ has_upper = !!(msg_ctrl & BIT(7));
+ msg_addr_lower = dw_pcie_readl_dbi(pci, cap_addr + 0x4);
+ if (has_upper) {
+ msg_addr_upper = dw_pcie_readl_dbi(pci, cap_addr + 0x8);
+ msg_data = dw_pcie_readl_dbi(pci, cap_addr + 0xc) &
+ GENMASK(15, 0);
+ } else {
+ msg_addr_upper = 0;
+ msg_data = dw_pcie_readl_dbi(pci, cap_addr + 0x8) &
+ GENMASK(15, 0);
+ }
+ msg_addr = ((u64) msg_addr_upper) << 32 | msg_addr_lower;
+ ret = epc->ops->map_addr(epc, ep->msi_mem_phys, msg_addr, PAGE_SIZE);
+ if (ret)
+ return ret;
+
+ writel(msg_data | (interrupt_num - 1), ep->msi_mem);
+
+ epc->ops->unmap_addr(epc, ep->msi_mem_phys);
+
+ return 0;
+}
+
+static int artpec6_pcie_raise_irq(struct dw_pcie_ep *ep,
+ enum pci_epc_irq_type type, u8 interrupt_num)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+
+ switch (type) {
+ case PCI_EPC_IRQ_LEGACY:
+ dev_err(pci->dev, "EP cannot trigger legacy IRQs\n");
+ return -EINVAL;
+ case PCI_EPC_IRQ_MSI:
+ return artpec6_pcie_raise_msi_irq(ep, interrupt_num);
+ default:
+ dev_err(pci->dev, "UNKNOWN IRQ type\n");
+ }
+
+ return 0;
+}
+
+static struct dw_pcie_ep_ops pcie_ep_ops = {
+ .ep_init = artpec6_pcie_ep_init,
+ .raise_irq = artpec6_pcie_raise_irq,
+};
+
+static int artpec6_add_pcie_ep(struct artpec6_pcie *artpec6_pcie,
+ struct platform_device *pdev)
+{
+ int ret;
+ struct dw_pcie_ep *ep;
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct dw_pcie *pci = artpec6_pcie->pci;
+
+ ep = &pci->ep;
+ ep->ops = &pcie_ep_ops;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi2");
+ pci->dbi_base2 = devm_ioremap(dev, res->start, resource_size(res));
+ if (IS_ERR(pci->dbi_base2))
+ return PTR_ERR(pci->dbi_base2);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "addr_space");
+ if (!res)
+ return -EINVAL;
+
+ ep->phys_base = res->start;
+ ep->addr_size = resource_size(res);
+
+ ret = dw_pcie_ep_init(ep);
+ if (ret) {
+ dev_err(dev, "failed to initialize endpoint\n");
+ return ret;
+ }
+
+ return 0;
+}
+
static int artpec6_add_pcie_port(struct artpec6_pcie *artpec6_pcie,
struct platform_device *pdev)
{
@@ -234,6 +383,8 @@ static int artpec6_add_pcie_port(struct artpec6_pcie *artpec6_pcie,
static const struct dw_pcie_ops dw_pcie_ops = {
.cpu_addr_fixup = artpec6_pcie_cpu_addr_fixup,
+ .start_link = artpec6_pcie_establish_link,
+ .stop_link = artpec6_pcie_stop_link,
};
static int artpec6_pcie_probe(struct platform_device *pdev)
@@ -244,6 +395,16 @@ static int artpec6_pcie_probe(struct platform_device *pdev)
struct resource *dbi_base;
struct resource *phy_base;
int ret;
+ const struct of_device_id *match;
+ const struct artpec_pcie_of_data *data;
+ enum dw_pcie_device_mode mode;
+
+ match = of_match_device(artpec6_pcie_of_match, dev);
+ if (!match)
+ return -EINVAL;
+
+ data = (struct artpec_pcie_of_data *)match->data;
+ mode = (enum dw_pcie_device_mode)data->mode;
artpec6_pcie = devm_kzalloc(dev, sizeof(*artpec6_pcie), GFP_KERNEL);
if (!artpec6_pcie)
@@ -257,6 +418,7 @@ static int artpec6_pcie_probe(struct platform_device *pdev)
pci->ops = &dw_pcie_ops;
artpec6_pcie->pci = pci;
+ artpec6_pcie->mode = mode;
dbi_base = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
pci->dbi_base = devm_ioremap_resource(dev, dbi_base);
@@ -276,15 +438,47 @@ static int artpec6_pcie_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, artpec6_pcie);
- ret = artpec6_add_pcie_port(artpec6_pcie, pdev);
- if (ret < 0)
- return ret;
+ switch (artpec6_pcie->mode) {
+ case DW_PCIE_RC_TYPE:
+ ret = artpec6_add_pcie_port(artpec6_pcie, pdev);
+ if (ret < 0)
+ return ret;
+ break;
+ case DW_PCIE_EP_TYPE: {
+ u32 val;
+
+ val = artpec6_pcie_readl(artpec6_pcie, PCIECFG);
+ val &= ~PCIECFG_DEVICE_TYPE_MASK;
+ artpec6_pcie_writel(artpec6_pcie, PCIECFG, val);
+ ret = artpec6_add_pcie_ep(artpec6_pcie, pdev);
+ if (ret < 0)
+ return ret;
+ break;
+ }
+ default:
+ dev_err(dev, "INVALID device type %d\n", artpec6_pcie->mode);
+ }
return 0;
}
+static const struct artpec_pcie_of_data artpec6_pcie_rc_of_data = {
+ .mode = DW_PCIE_RC_TYPE,
+};
+
+static const struct artpec_pcie_of_data artpec6_pcie_ep_of_data = {
+ .mode = DW_PCIE_EP_TYPE,
+};
+
static const struct of_device_id artpec6_pcie_of_match[] = {
- { .compatible = "axis,artpec6-pcie", },
+ {
+ .compatible = "axis,artpec6-pcie",
+ .data = &artpec6_pcie_rc_of_data,
+ },
+ {
+ .compatible = "axis,artpec6-pcie-ep",
+ .data = &artpec6_pcie_ep_of_data,
+ },
{},
};
--
2.11.0
