Add binding document for Mediatek PCIe Gen2 v1 host controller driver.
Signed-off-by: Ryder Lee <ryder.lee@xxxxxxxxxxxx>
---
.../bindings/pci/mediatek,gen2v1-pcie.txt | 174 +++++++++++++++++++++
1 file changed, 174 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/mediatek,gen2v1-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/mediatek,gen2v1-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek,gen2v1-pcie.txt
new file mode 100644
index 0000000..545d8cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/mediatek,gen2v1-pcie.txt
@@ -0,0 +1,174 @@
+Mediatek Gen2 V1 PCIe controller
+
+PCIe subsys supports single root complex (RC) with 3 Root Ports. Each root
+ports supports a Gen2 1-lane Link. It includes one Host/PCI bridge and 3
+PCIe MAC. Each port has PIPE interface to PHY. There are 3 bus master for
+data access and 1 bus slave for Configuration and Status Register access.
+
+This controller is available on MT7623 series SoCs.
+
+Required properties:
+- compatible: Should contain "mediatek,gen2v1-pcie".
+- device_type: Must be "pci"
+- reg: Base addresses and lengths of the PCIe controller.
+- #address-cells: Address representation for root ports (must be 3)
+ - cell 0 specifies the bus and device numbers of the root port:
+ [23:16]: bus number
+ [15:11]: device number
+ - cell 1 denotes the upper 32 address bits and should be 0
+ - cell 2 contains the lower 32 address bits and is used to translate to the
+ CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupts: Three interrupt outputs of the controller. Must contain an
+ entry for each entry in the interrupt-names property.
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - free_ck :for reference clock of PCIe subsys
+ - sys_ck0 :for clock of Port0 MAC
+ - sys_ck1 :for clock of Port1 MAC
+ - sys_ck2 :for clock of Port2 MAC
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - pcie-rst0 :port0 reset
+ - pcie-rst1 :port1 reset
+ - pcie-rst2 :port2 reset
+- phys: list of PHY specifiers (used by generic PHY framework)
+- phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
+ number of PHYs as specified in *phys* property.
+- power-domains: A phandle and power domain specifier pair to the power domain
+ which is responsible for collapsing and restoring power to the peripheral
+- bus-range: Range of bus numbers associated with this controller
+- ranges: Describes the translation of addresses for root ports and standard
+ PCI regions. The entries must be 6 cells each, where the first three cells
+ correspond to the address as described for the #address-cells property
+ above, the fourth cell is the physical CPU address to translate to and the
+ fifth and six cells are as described for the #size-cells property above.
+ - The first three entries are expected to translate the addresses for the root
+ port registers, which are referenced by the assigned-addresses property of
+ the root port nodes (see below).
+ - The remaining entries setup the mapping for the standard I/O and memory
+ regions.
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+
+In addition, the device tree node must have sub-nodes describing each
+PCIe port interface, having the following mandatory properties:
+
+Required properties:
+- device_type: Must be "pci"
+- assigned-addresses: Address and size of the port configuration registers
+- reg: Only the first four bytes are used to refer to the correct bus number
+ and device number.
+- #address-cells: Must be 3
+- #size-cells: Must be 2
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+- ranges: Sub-ranges distributed from the PCIe controller node. An empty
+ property is sufficient.
+- num-lanes: Number of lanes to use for this port.
+
+Examples:
+
+SoC dtsi:
+
+ hifsys: syscon@1a000000 {
+ compatible = "mediatek,mt7623-hifsys", "syscon";
+ reg = <0 0x1a000000 0 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pcie: pcie-controller@1a140000 {
+ compatible = "mediatek,gen2v1-pcie";
+ device_type = "pci";
+ reg = <0 0x1a140000 0 0x1000>; /* PCIe shared registers */
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-map-mask = <0xf800 0 0 0>;
+ interrupt-map = <0x0000 0 0 0 &gic GIC_SPI 193 IRQ_TYPE_NONE>,
+ <0x0800 0 0 0 &gic GIC_SPI 194 IRQ_TYPE_NONE>,
+ <0x1000 0 0 0 &gic GIC_SPI 195 IRQ_TYPE_NONE>;
+ clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
+ <&hifsys CLK_HIFSYS_PCIE0>,
+ <&hifsys CLK_HIFSYS_PCIE1>,
+ <&hifsys CLK_HIFSYS_PCIE2>;
+ clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
+ resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
+ <&hifsys MT2701_HIFSYS_PCIE1_RST>,
+ <&hifsys MT2701_HIFSYS_PCIE2_RST>;
+ reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
+ phys = <&pcie0_phy>, <&pcie1_phy>, <&pcie2_phy>;
+ phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
+ bus-range = <0x00 0xff>;
+ ranges = <0x82000000 0 0x1a142000 0 0x1a142000 0 0x1000 /* Port0 registers */
+ 0x82000000 0 0x1a143000 0 0x1a143000 0 0x1000 /* Port1 registers */
+ 0x82000000 0 0x1a144000 0 0x1a144000 0 0x1000 /* Port2 registers */
+ 0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */
+ 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */
+ status = "disabled";
+
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000000 0 0x1a142000 0 0x1000>;
+ reg = <0x0000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 193 IRQ_TYPE_NONE>;
+ ranges;
+ num-lanes = <1>;
+ status = "disabled";
+ };
+
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x1a143000 0 0x1000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 194 IRQ_TYPE_NONE>;
+ ranges;
+ num-lanes = <1>;
+ status = "disabled";
+ };
+
+ pcie@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x1a144000 0 0x1000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 195 IRQ_TYPE_NONE>;
+ ranges;
+ num-lanes = <1>;
+ status = "disabled";
+ };
+ };
+
+Board dts:
+
+ &pcie {
+ status = "okay";
+
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
--
1.9.1
