On 24/01/2017 08:05, zhichang.yuan wrote:
The low-pin-count(LPC) interface of Hip06/Hip07 accesses the peripherals in
I/O port addresses. This patch implements the LPC host controller driver which
perform the I/O operations on the underlying hardware.
We don't want to touch those existing peripherals' driver, such as ipmi-bt. So
this driver applies the indirect-IO introduced in the previous patch after
registering an indirect-IO node to the indirect-IO devices list which will be
searched in the I/O accessors.
As the I/O translations for LPC children depend on the host I/O registration,
we should ensure the host I/O registration is finished before all the LPC
children scanning. That is why an arch_init() hook was added in this patch.
Signed-off-by: zhichang.yuan <yuanzhichang@xxxxxxxxxxxxx>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@xxxxxxxxxx>
---
.../arm/hisilicon/hisilicon-low-pin-count.txt | 33 ++
MAINTAINERS | 9 +
arch/arm64/boot/dts/hisilicon/hip06-d03.dts | 4 +
arch/arm64/boot/dts/hisilicon/hip06.dtsi | 14 +
drivers/bus/Kconfig | 8 +
drivers/bus/Makefile | 1 +
drivers/bus/hisi_lpc.c | 599 +++++++++++++++++++++
7 files changed, 668 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt
create mode 100644 drivers/bus/hisi_lpc.c
diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt
new file mode 100644
index 0000000..213181f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt
@@ -0,0 +1,33 @@
+Hisilicon Hip06 low-pin-count device
+ Hisilicon Hip06 SoCs implement a Low Pin Count (LPC) controller, which
+ provides I/O access to some legacy ISA devices.
+ Hip06 is based on arm64 architecture where there is no I/O space. So, the
+ I/O ports here are not cpu addresses, and there is no 'ranges' property in
+ LPC device node.
+
+Required properties:
+- compatible: value should be as follows:
+ (a) "hisilicon,hip06-lpc"
+ (b) "hisilicon,hip07-lpc"
+- #address-cells: must be 2 which stick to the ISA/EISA binding doc.
+- #size-cells: must be 1 which stick to the ISA/EISA binding doc.
+- reg: base memory range where the LPC register set is mapped.
+
+Note:
+ The node name before '@' must be "isa" to represent the binding stick to the
+ ISA/EISA binding specification.
+
+Example:
+
+isa@a01b0000 {
+ compatible = "hisilicon,hip06-lpc";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0x0 0xa01b0000 0x0 0x1000>;
+
+ ipmi0: bt@e4 {
+ compatible = "ipmi-bt";
+ device_type = "ipmi";
+ reg = <0x01 0xe4 0x04>;
+ };
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 26edd83..0153707 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5855,6 +5855,15 @@ F: include/uapi/linux/if_hippi.h
F: net/802/hippi.c
F: drivers/net/hippi/
+HISILICON LPC BUS DRIVER
+M: Zhichang Yuan <yuanzhichang@xxxxxxxxxxxxx>
+L: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
+W: http://www.hisilicon.com
+S: Maintained
+F: drivers/bus/hisi_lpc.c
+F: lib/extio.c
+F: Documentation/devicetree/bindings/arm/hisilicon/hisilicon-low-pin-count.txt
+
HISILICON NETWORK SUBSYSTEM DRIVER
M: Yisen Zhuang <yisen.zhuang@xxxxxxxxxx>
M: Salil Mehta <salil.mehta@xxxxxxxxxx>
diff --git a/arch/arm64/boot/dts/hisilicon/hip06-d03.dts b/arch/arm64/boot/dts/hisilicon/hip06-d03.dts
index 7c4114a..75b2b5c 100644
--- a/arch/arm64/boot/dts/hisilicon/hip06-d03.dts
+++ b/arch/arm64/boot/dts/hisilicon/hip06-d03.dts
@@ -52,3 +52,7 @@
&usb_ehci {
status = "ok";
};
+
+&ipmi0 {
+ status = "ok";
+};
diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
index a049b64..c450f8d 100644
--- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
@@ -318,6 +318,20 @@
#size-cells = <2>;
ranges;
+ isa@a01b0000 {
+ compatible = "hisilicon,hip06-lpc";
+ #size-cells = <1>;
+ #address-cells = <2>;
+ reg = <0x0 0xa01b0000 0x0 0x1000>;
+
+ ipmi0: bt@e4 {
+ compatible = "ipmi-bt";
+ device_type = "ipmi";
+ reg = <0x01 0xe4 0x04>;
+ status = "disabled";
+ };
+ };
+
refclk: refclk {
compatible = "fixed-clock";
clock-frequency = <50000000>;
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index b9e8cfc..58cee84 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -64,6 +64,14 @@ config BRCMSTB_GISB_ARB
arbiter. This driver provides timeout and target abort error handling
and internal bus master decoding.
+config HISILICON_LPC
+ bool "Workaround for nonstandard ISA I/O space on Hisilicon Hip0X"
It's not a workaround, it's support. Better word it like
"Support for ISA I/O space on Hisilicon HIP0X"
+ depends on (ARM64 && ARCH_HISI && PCI) || COMPILE_TEST
+ select INDIRECT_PIO
+ help
+ Driver needed for some legacy ISA devices attached to Low-Pin-Count
+ on Hisilicon Hip0X SoC.
+
config IMX_WEIM
bool "Freescale EIM DRIVER"
depends on ARCH_MXC
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index cc6364b..28e3862 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_ARM_CCI) += arm-cci.o
obj-$(CONFIG_ARM_CCN) += arm-ccn.o
obj-$(CONFIG_BRCMSTB_GISB_ARB) += brcmstb_gisb.o
+obj-$(CONFIG_HISILICON_LPC) += hisi_lpc.o
obj-$(CONFIG_IMX_WEIM) += imx-weim.o
obj-$(CONFIG_MIPS_CDMM) += mips_cdmm.o
obj-$(CONFIG_MVEBU_MBUS) += mvebu-mbus.o
diff --git a/drivers/bus/hisi_lpc.c b/drivers/bus/hisi_lpc.c
new file mode 100644
index 0000000..a96e384
--- /dev/null
+++ b/drivers/bus/hisi_lpc.c
@@ -0,0 +1,599 @@
+/*
+ * Copyright (C) 2016 Hisilicon Limited, All Rights Reserved.
+ * Author: Zhichang Yuan <yuanzhichang@xxxxxxxxxxxxx>
+ * Author: Zou Rongrong <zourongrong@xxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/acpi.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+/*
+ * Setting this bit means each IO operation will target to a
+ * different port address:
+ * 0 means repeatedly IO operations will stick on the same port,
+ * such as BT;
+ */
+#define FG_INCRADDR_LPC 0x02
+
+struct lpc_cycle_para {
+ unsigned int opflags;
+ unsigned int csize; /* the data length of each operation */
+};
+
+struct hisilpc_dev {
+ spinlock_t cycle_lock;
+ void __iomem *membase;
+ struct extio_node *extio;
+};
+
+/* bounds of the LPC bus address range */
+#define LPC_MIN_BUS_RANGE 0x0
+
+/*
+ * The maximal IO size for each leagcy bus.
legacy?
I don't really understand why this bus is legacy though. It looks like a
simple MMIO-to-LPC bridge to me.
+ * The port size of legacy I/O devices is normally less than 0x400.
+ * Defining the I/O range size as 0x400 here should be sufficient for
+ * all peripherals under one bus.
+ */
This comment doesn't make a lot of sense. What is the limit? Is there a
hardware limit?
We don't dynamically allocate devices on the lpc bus, so why imply a
limit at all?
+#define LPC_BUS_IO_SIZE 0x400
+
+/* The maximum continuous operations */
+#define LPC_MAX_OPCNT 16
+/* only support IO data unit length is four at maximum */
+#define LPC_MAX_DULEN 4
+#if LPC_MAX_DULEN > LPC_MAX_OPCNT
+#error "LPC.. MAX_DULEN must be not bigger than MAX_OPCNT!"
+#endif
+
+#define LPC_REG_START 0x00 /* start a new LPC cycle */
+#define LPC_REG_OP_STATUS 0x04 /* the current LPC status */
+#define LPC_REG_IRQ_ST 0x08 /* interrupt enable&status */
+#define LPC_REG_OP_LEN 0x10 /* how many LPC cycles each start */
+#define LPC_REG_CMD 0x14 /* command for the required LPC cycle */
+#define LPC_REG_ADDR 0x20 /* LPC target address */
+#define LPC_REG_WDATA 0x24 /* data to be written */
+#define LPC_REG_RDATA 0x28 /* data coming from peer */
+
+
+/* The command register fields */
+#define LPC_CMD_SAMEADDR 0x08
+#define LPC_CMD_TYPE_IO 0x00
+#define LPC_CMD_WRITE 0x01
+#define LPC_CMD_READ 0x00
+/* the bit attribute is W1C. 1 represents OK. */
+#define LPC_STAT_BYIRQ 0x02
+
+#define LPC_STATUS_IDLE 0x01
+#define LPC_OP_FINISHED 0x02
+
+#define START_WORK 0x01
+
+/*
+ * The minimal waiting interval... Suggest it is not less than 10.
+ * Bigger value probably will lower the performance.
Are you sure you want this comment to be upstream? :)
+ */
+#define LPC_NSEC_PERWAIT 100
+/*
+ * The maximum waiting time is about 128us.
+ * The fastest IO cycle time is about 390ns, but the worst case will wait
+ * for extra 256 lpc clocks, so (256 + 13) * 30ns = 8 us. The maximum
+ * burst cycles is 16. So, the maximum waiting time is about 128us under
+ * worst case.
+ * choose 1300 as the maximum.
+ */
+#define LPC_MAX_WAITCNT 1300
+/* About 10us. This is specific for single IO operation, such as inb. */
+#define LPC_PEROP_WAITCNT 100
+
+
+static inline int wait_lpc_idle(unsigned char *mbase,
No need to specify inline.
+ unsigned int waitcnt) {
+ u32 opstatus;
+
+ while (waitcnt--) {
+ ndelay(LPC_NSEC_PERWAIT);
+ opstatus = readl(mbase + LPC_REG_OP_STATUS);
+ if (opstatus & LPC_STATUS_IDLE)
+ return (opstatus & LPC_OP_FINISHED) ? 0 : (-EIO);
It's a shame we have to busy loop, but I guess no calling code outside
is prepared for rescheduling at this point.
+ }
+ return -ETIME;
+}
+
+/*
+ * hisilpc_target_in - trigger a series of lpc cycles to read required data
+ * from target peripheral.
+ * @pdev: pointer to hisi lpc device
+ * @para: some parameters used to control the lpc I/O operations
+ * @ptaddr: the lpc I/O target port address
+ * @buf: where the read back data is stored
+ * @opcnt: how many I/O operations required in this calling
+ *
+ * Only one byte data is read each I/O operation.
+ *
+ * Returns 0 on success, non-zero on fail.
+ *
+ */
+static int
+hisilpc_target_in(struct hisilpc_dev *lpcdev, struct lpc_cycle_para *para,
+ unsigned long ptaddr, unsigned char *buf,
+ unsigned long opcnt)
+{
+ unsigned long cnt_per_trans;
+ unsigned int cmd_word;
+ unsigned int waitcnt;
+ int ret;
+
+ if (!buf || !opcnt || !para || !para->csize || !lpcdev)
+ return -EINVAL;
+
+ if (opcnt > LPC_MAX_OPCNT)
+ return -EINVAL;
+
+ cmd_word = LPC_CMD_TYPE_IO | LPC_CMD_READ;
+ waitcnt = LPC_PEROP_WAITCNT;
+ if (!(para->opflags & FG_INCRADDR_LPC)) {
+ cmd_word |= LPC_CMD_SAMEADDR;
+ waitcnt = LPC_MAX_WAITCNT;
+ }
+
+ ret = 0;
+ cnt_per_trans = (para->csize == 1) ? opcnt : para->csize;
+ for (; opcnt && !ret; cnt_per_trans = para->csize) {
+ unsigned long flags;
+
+ /* whole operation must be atomic */
+ spin_lock_irqsave(&lpcdev->cycle_lock, flags);
Ouch. This is going to kill your RT jitter. Is there no better way?
+
+ writel(cnt_per_trans, lpcdev->membase + LPC_REG_OP_LEN);
+
+ writel(cmd_word, lpcdev->membase + LPC_REG_CMD);
+
+ writel(ptaddr, lpcdev->membase + LPC_REG_ADDR);
+
+ writel(START_WORK, lpcdev->membase + LPC_REG_START);
+
+ /* whether the operation is finished */
+ ret = wait_lpc_idle(lpcdev->membase, waitcnt);
+ if (!ret) {
+ opcnt -= cnt_per_trans;
+ for (; cnt_per_trans--; buf++)
+ *buf = readl(lpcdev->membase + LPC_REG_RDATA);
+ }
+
+ spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+ }
+
+ return ret;
+}
+
+/**
+ * hisilpc_target_out - trigger a series of lpc cycles to write required
+ * data to target peripheral.
+ * @pdev: pointer to hisi lpc device
+ * @para: some parameters used to control the lpc I/O operations
+ * @ptaddr: the lpc I/O target port address
+ * @buf: where the data to be written is stored
+ * @opcnt: how many I/O operations required
+ *
+ * Only one byte data is read each I/O operation.
+ *
+ * Returns 0 on success, non-zero on fail.
+ *
+ */
+static int
+hisilpc_target_out(struct hisilpc_dev *lpcdev, struct lpc_cycle_para *para,
+ unsigned long ptaddr, const unsigned char *buf,
+ unsigned long opcnt)
+{
+ unsigned long cnt_per_trans;
+ unsigned int cmd_word;
+ unsigned int waitcnt;
+ int ret;
+
+ if (!buf || !opcnt || !para || !lpcdev)
+ return -EINVAL;
+
+ if (opcnt > LPC_MAX_OPCNT)
+ return -EINVAL;
+ /* default is increasing address */
+ cmd_word = LPC_CMD_TYPE_IO | LPC_CMD_WRITE;
+ waitcnt = LPC_PEROP_WAITCNT;
+ if (!(para->opflags & FG_INCRADDR_LPC)) {
+ cmd_word |= LPC_CMD_SAMEADDR;
+ waitcnt = LPC_MAX_WAITCNT;
+ }
+
+ ret = 0;
+ cnt_per_trans = (para->csize == 1) ? opcnt : para->csize;
+ for (; opcnt && !ret; cnt_per_trans = para->csize) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&lpcdev->cycle_lock, flags);
Same thing here
+
+ writel(cnt_per_trans, lpcdev->membase + LPC_REG_OP_LEN);
+ opcnt -= cnt_per_trans;
+ for (; cnt_per_trans--; buf++)
+ writel(*buf, lpcdev->membase + LPC_REG_WDATA);
+
+ writel(cmd_word, lpcdev->membase + LPC_REG_CMD);
+
+ writel(ptaddr, lpcdev->membase + LPC_REG_ADDR);
+
+ writel(START_WORK, lpcdev->membase + LPC_REG_START);
+
+ /* whether the operation is finished */
+ ret = wait_lpc_idle(lpcdev->membase, waitcnt);
+
+ spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+ }
+
+ return ret;
+}
+
+static inline unsigned long
Don't explicitly mention inline, the compiler will figure that out for you.
+hisi_lpc_pio_to_addr(struct hisilpc_dev *lpcdev, unsigned long pio)
+{
+ return pio - lpcdev->extio->io_start + lpcdev->extio->bus_start;
+}
+
+
+/**
+ * hisilpc_comm_in - read/input the data from the I/O peripheral
+ * through LPC.
+ * @devobj: pointer to the device information relevant to LPC controller.
+ * @pio: the target I/O port address.
+ * @dlen: the data length required to read from the target I/O port.
+ *
+ * when succeed, the data read back is stored in buffer pointed by inbuf.
+ * For inb, return the data read from I/O or -1 when error occur.
+ */
+static u64 hisilpc_comm_in(void *devobj, unsigned long pio, size_t dlen)
+{
+ struct hisilpc_dev *lpcdev = devobj;
+ struct lpc_cycle_para iopara;
+ u32 rd_data;
rd_data needs to be initialized to 0. Otherwise it may contain stale
stack contents and corrupt non-32bit dlen returns.
+ unsigned char *newbuf;
+ int ret = 0;
+ unsigned long ptaddr;
+
+ if (!lpcdev || !dlen || dlen > LPC_MAX_DULEN || (dlen & (dlen - 1)))
+ return -1;
Isn't this -EINVAL?
+
+ /* the local buffer must be enough for one data unit */
+ if (sizeof(rd_data) < dlen)
+ return -1;
Same here.
Also, the above seems a very convoluted way of saying
switch (dlen) {
case 1:
case 2:
case 4:
break;
default:
return -EINVAL;
}
But I guess the way you write it doesn't hurt ;)
Alex
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
