On Mon, Dec 26, 2016 at 02:20:29PM +0900, Jaehoon Chung wrote:
> Add the Exxynos5433 pcie node for TM2.
> This pcie device is used for supporting WiFi.
>
> And some gpios are already requested from pinctrl. so it doesn't need to
> initialize.
> GPJ2-0 is used for supplying to WiFi PCIe chip.
>
> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi | 7 +++++++
> arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 11 +++++++++--
> arch/arm64/boot/dts/exynos/exynos5433.dtsi | 23 ++++++++++++++++++++++
> 3 files changed, 39 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
> index ad71247..3e8b728 100644
> --- a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
> @@ -183,6 +183,13 @@
> interrupt-controller;
> #interrupt-cells = <2>;
> };
> +
> + pcie_wlanen: pcie-wlanen {
> + samsung,pins = "gpj2-0";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <3>;
> + };
> };
>
> &pinctrl_finger {
> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> index f21bdc2..c84a2ad 100644
> --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> @@ -737,6 +737,15 @@
> bus-width = <4>;
> };
>
> +&pcie {
> + assigned-clocks = <&cmu_fsys CLK_MOUT_SCLK_PCIE_100_USER>,
> + <&cmu_top CLK_MOUT_SCLK_PCIE_100>;
> + assigned-clock-parents = <&cmu_top CLK_SCLK_PCIE_100_FSYS>,
> + <&cmu_top CLK_MOUT_BUS_PLL_USER>;
> + assigned-clock-rates = <0>, <100000000>;
> + status = "okay";
> +};
> +
> &pinctrl_alive {
> pinctrl-names = "default";
> pinctrl-0 = <&initial_alive>;
> @@ -836,7 +845,6 @@
> pinctrl-0 = <&initial_ese>;
>
> initial_ese: initial-state {
> - PIN(IN, gpj2-0, DOWN, LV1);
> PIN(IN, gpj2-1, DOWN, LV1);
> PIN(IN, gpj2-2, DOWN, LV1);
> };
> @@ -851,7 +859,6 @@
> PIN(IN, gpr3-1, DOWN, LV1);
> PIN(IN, gpr3-2, DOWN, LV1);
> PIN(IN, gpr3-3, DOWN, LV1);
> - PIN(IN, gpr3-7, NONE, LV1);
> };
> };
>
> diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
> index 2a15f18..da287f4 100644
> --- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
> @@ -1457,6 +1457,29 @@
> samsung,fsys-sysreg = <&syscon_fsys>;
> status = "okay";
> };
> +
> + pcie: pcie@15700000 {
> + compatible = "samsung,exynos5433-pcie", "snps,dw-pcie";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "intr";
> + clocks = <&cmu_fsys CLK_PCIE>,
> + <&cmu_fsys CLK_PCLK_PCIE_PHY>;
Here and in the 'reg' property - indentation looks weird. Tabs+spaces
but not aligned. Either you use spaces to align... or just don't care
and use tabs. I prefer consistency and below the 'ranges' property is
aligned.
> + clock-names = "pcie", "pcie_bus";
> + num-lanes = <1>;
> + pinctrl-names = "default";
> + phys = <&pcie_phy>;
> + phy-names = "pcie-phy";
> + pinctrl-0 = <&pcie_bus &pcie_wlanen>;
> + reg = <0x156b0000 0x1000>, <0x15700000 0x1000>,
> + <0x0c000000 0x1000>;
> + reg-names = "elbi", "dbi", "config";
This does not match the bindings documentation.
Best regards,
Krzysztof
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
