On Fri, Nov 04, 2016 at 12:59:46PM +0000, Srinivas Kandagatla wrote:
> This patch adds support to msm8996/apq8096 pcie, MSM8996 supports
> Gen 1/2, One lane, 3 pcie root-complex with support to MSI and
> legacy interrupts and it conforms to PCI Express Base 2.1 specification.
>
> This patch adds post_init callback to qcom_pcie_ops, as this is pcie
> pipe clocks are only setup after the phy is powered on.
> It also adds ltssm_enable callback as it is very much different to other
> supported SOCs in the driver.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
> ---
> .../devicetree/bindings/pci/qcom,pcie.txt | 68 +++++++-
> drivers/pci/host/pcie-qcom.c | 177 ++++++++++++++++++++-
> 2 files changed, 239 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> index 4059a6f..4a0538d 100644
> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> @@ -7,6 +7,7 @@
> - "qcom,pcie-ipq8064" for ipq8064
> - "qcom,pcie-apq8064" for apq8064
> - "qcom,pcie-apq8084" for apq8084
> + - "qcom,pcie-msm8996" for msm8996 or apq8096
>
> - reg:
> Usage: required
> @@ -92,6 +93,16 @@
> - "aux" Auxiliary (AUX) clock
> - "bus_master" Master AXI clock
> - "bus_slave" Slave AXI clock
> +
> +- clock-names:
> + Usage: required for msm8996/apq8096
> + Value type: <stringlist>
> + Definition: Should contain the following entries
> + - "aux" Auxiliary (AUX) clock.
> + - "bus_master" Master AXI clock.
> + - "bus_slave" Slave AXI clock.
> + - "pipe" Pipe Clock driving internal logic.
> + - "cfg" Configuration clk.
The order here and the order in the example don't match. The order
should be defined.
> - resets:
> Usage: required
> Value type: <prop-encoded-array>
> @@ -115,7 +126,7 @@
> - "core" Core reset
>
> - power-domains:
> - Usage: required for apq8084
> + Usage: required for apq8084 and msm8996/apq8096
> Value type: <prop-encoded-array>
> Definition: A phandle and power domain specifier pair to the
> power domain which is responsible for collapsing
> @@ -231,3 +242,58 @@
> pinctrl-0 = <&pcie0_pins_default>;
> pinctrl-names = "default";
> };
> +
> +* Example for apq8096:
> +
> + pcie@00608000{
Drop leading 0s.
> + compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
> + power-domains = <&gcc PCIE1_GDSC>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> +
> + status = "disabled";
No point to have status in the example.
> +
> + reg = <0x00608000 0x2000>,
> + <0x0d000000 0xf1d>,
> + <0x0d000f20 0xa8>,
> + <0x0d100000 0x100000>;
> +
> + reg-names = "parf", "dbi", "elbi", "config";
> +
> + phys = <&pcie_phy 1>;
> + phy-names = "pciephy";
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>,
> + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
> +
> + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
> + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
> +
> + vdda-1p8-supply = <&pm8994_l12>;
> + vdda-supply = <&pm8994_l28>;
> + linux,pci-domain = <1>;
> +
> + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
> + <&gcc GCC_PCIE_1_AUX_CLK>,
> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_1_SLV_AXI_CLK>;
> +
> + clock-names = "pipe",
> + "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave";
> + };
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
